Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Tony Pearson is a Master Inventor and Senior Software Engineer for the IBM Storage product line at the
IBM Executive Briefing Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services. You can also follow him on Twitter @az990tony.
(Short URL for this blog: ibm.co/Pearson
Have you ever noticed that sometimes two movies come out that seem eerily similar to each other, released by different studios within months or weeks of each other? My sister used to review film scripts for a living, she would read ten of them and have to pick her top three favorites, and tells me that scripts for nearly identical concepts came all the time. Here are a few of my favorite examples:
1994: [Wyatt Earp] and [Tombstone] were Westerns recounting the famed gunfight at the O.K. Corral. Tombstone, Arizona is near Tucson, and the gunfight is recreated fairly often for tourists.
1998: [Armageddon] and [Deep Impact] were a pair of disaster movies dealing with a large rock heading to destroy all life on earth. I was in Mazatlan, Mexico to see the latter, dubbed in Spanish as "Impacto Profundo".
1998: [A Bug's Life] and [Antz] were computer-animated tales of the struggle of one individual ant in an ant colony.
2000: [Mission to Mars] and [Red Planet] were sci-fi pics exploring what a manned mission to our neighboring planet might entail.
This is different than copy-cat movies that are re-made or re-imagined many years later based on the previous successes of an original. Ever since my blog post [VPLEX: EMC's Latest Wheel is Round] in 2010 comparing EMC's copy-cat product that came our seven years after IBM's SAN Volume Controller (SVC), I've noticed EMC doesn't talk about VPLEX that much anymore.
This week, IBM announced [XIV Gen3 Solid-State Drive support] and our friends over at EMC announced [VFCache SSD-based PCIe cards]. Neither of these should be a surprise to anyone who follows the IT industry, as IBM had announced its XIV Gen3 as "SSD-Ready" last year specifically for this purpose, and EMC has been touting its "Project Lightning" since last May.
Fellow blogger Chuck Hollis from EMC has a blog post [VFCache means Very Fast Cache indeed] that provides additional detail. Chuck claims the VFCache is faster than popular [Fusion-IO PCIe cards] available for IBM servers. I haven't seen the performance spec sheets, but typically SSD is four to five times slower than the DRAM cache used in the XIV Gen3. The VFCache's SSD is probably similar in performance to the SSD supported in the IBM XIV Gen3, DS8000, DS5000, SVC, N series, and Storwize V7000 disk systems.
Nonetheless, I've been asked my opinions on the comparison between these two announcements, as they both deal with improving application performance through the use of Solid-State Drives as an added layer of read cache.
(FTC Disclosure: I am both a full-time employee and stockholder of the IBM Corporation. The U.S. Federal Trade Commission may consider this blog post as a paid celebrity endorsement of IBM servers and storage systems. This blog post is based on my interpretation and opinions of publicly-available information, as I have no hands-on access to any of these third-party PCIe cards. I have no financial interest in EMC, Fusion-IO, Texas Memory Systems, or any other third party vendor of PCIe cards designed to fit inside IBM servers, and I have not been paid by anyone to mention their name, brands or products on this blog post.)
The solutions are different in that IBM XIV Gen3 the SSD is "storage-side" in the external storage device, and EMC VFCache is "server-side" as a PCI Express [PCIe] card. Aside from that, both implement SSD as an additional read cache layer in front of spinning disk to boost performance. Neither is an industry first, as IBM has offered server-side SSD since 2007, and IBM and EMC have offered storage-side SSD in many of their other external storage devices. The use of SSD as read cache has already been available in IBM N series using [Performance Accelerator Module (PAM)] cards.
IBM has offered cooperative caching synergy between its servers and its storage arrays for some time now. The predecessor to today's POWER7-based were the iSeries i5 servers that used PCI-X IOP cards with cache to connect i5/OS applications to IBM's external disk and tape systems. To compete in this space, EMC created their own PCI-X cards to attach their own disk systems. In 2006, IBM did the right thing for our clients and fostered competition by entering in a [Landmark agreement] with EMC to [license the i5 interfaces]. Today, VIOS on IBM POWER systems allows a much broader choice of disk options for IBM i clients, including the IBM SVC, Storwize V7000 and XIV storage systems.
Can a little SSD really help performance? Yes! An IBM client running a [DB2 Universal Database] cluster across eight System x servers was able to replace an 800-drive EMC Symmetrix by putting eight SSD Fusion-IO cards in each server, for a total of 64 Solid-State drives, saving money and improving performance. DB2 has the Data Partitioning Feature that has multi-system DB2 configurations using a Grid-like architecture similar to how XIV is designed. Most IBM System x and BladeCenter servers support internal SSD storage options, and many offer PCIe slots for third-party SSD cards. Sadly, you can't do this with a VFCache card, since you can have only one VFCache card in each server, the data is unprotected, and only for ephemeral data like transaction logs or other temporary data. With multiple Fusion-IO cards in an IBM server, you can configure a RAID rank across the SSD, and use it for persistent storage like DB2 databases.
Here then is my side-by-side comparison:
IBM XIV Gen3 SSD Caching
Selected x86-based models of Cisco UCS, Dell PowerEdge, HP ProLiant DL, and IBM xSeries and System x servers
All of these, plus any other blade or rack-optimized server currently supported by XIV Gen3, including Oracle SPARC, HP Titanium, IBM POWER systems, and even IBM System z mainframes running Linux
Operating System support
Linux RHEL 5.6 and 5.7, VMware vSphere 4.1 and 5.0, and Windows 2008 x64 and R2.
All of these, plus all the other operating systems supported by XIV Gen3, including AIX, IBM i, Solaris, HP-UX, and Mac OS X
FCP and iSCSI
Vendor-supplied driver required on the server
Yes, the VFCache driver must be installed to use this feature.
No, IBM XIV Gen3 uses native OS-based multi-pathing drivers.
External disk storage systems required
None, it appears the VFCache has no direct interaction with the back-end disk array, so in theory the benefits are the same whether you use this VFCache card in front of EMC storage or IBM storage
XIV Gen3 is required, as the SSD slots are not available on older models of IBM XIV.
Shared disk support
No, VFCache has to be disabled and removed for vMotion to take place.
Yes! XIV Gen3 SSD caching shared disk supports VMware vMotion and Live Partition Mobility.
Support for multiple servers
An advantage of the XIV Gen3 SSD caching approach is that the cache can be dynamically allocated to the busiest data from any server or servers.
Support for active/active server clusters
Aware of changes made to back-end disk
No, it appears the VFCache has no direct interaction with the back-end disk array, so any changes to the data on the box itself are not communicated back to the VFCache card itself to invalidate the cache contents.
None identified. However, VFCache only caches blocks 64KB or smaller, so any sequential processing with larger blocks will bypass the VFCache.
Yes! XIV algorithms detect sequential access and avoid polluting the SSD with these blocks of data.
Number of SSD supported
One, which seems odd as IBM supports multiple Fusion-IO cards for its servers. However, this is not really a single point of failure (SPOF) as an application experiencing a VFCache failure merely drops down to external disk array speed, no data is lost since it is only read cache.
6 to 15 (one per XIV module) for high availability.
Pin data in SSD cache
Yes, using split-card mode, you can designate a portion of the 300GB to serve as Direct-attached storage (DAS). All data written to the DAS portion will be kept in SSD. However, since only one card is supported per server and the data is unprotected, this should only be used for ephemeral data like logs and temp files.
No, there is no option to designate an XIV Gen3 volume to be SSD-only. Consider using Fusion-IO PCIe card as a DAS alternative, or another IBM storage system for that requirement.
Pre-sales Estimating tools
Yes! CDF and Disk Magic tools are available to help cost-justify the purchase of SSD based on workload performance analysis.
IBM has the advantage that it designs and manufactures both servers and storage, and can design optimal solutions for our clients in that regard.
A client asked me to explain "Nearline storage" to them. This was easy, I thought, as I started my IBM career on DFHSM, now known as DFSMShsm for z/OS, which was created in 1977 to support the IBM 3850 Mass Storage System (MSS), a virtual storage system that blended disk drives and tape cartridges with robotic automation. Here is a quick recap:
Online storage is immediately available for I/O. This includes DRAM memory, solid-state drives (SSD), and always-on spinning disk, regardless of rotational speed.
Nearline storage is not immediately available, but can be made online quickly without human intervention. This includes optical jukeboxes, automated tape libraries, as well as spin-down massive array of idle disk (MAID) technologies.
Offline storage is not immediately available, and requires some human intervention to bring online. This can include USB memory sticks, CD/DVD optical media, shelf-resident tape cartridges, or other removable media.
Sadly, it appears a few storage manufacturers and vendors have been misusing the term "Nearline" to refer to "slower online" spinning disk drives. I find this [June 2005 technology paper from Seagate], and this [2002 NetApp Press Release], the latter of which included this contradiction for their "NearStore" disk array. Here is the excerpt:
"Providing online access to reference information—NetApp nearline storage solutions quickly retrieve and replicate reference and archive information maintained on cost-effective storage—medical images, financial models, energy exploration charts and graphs, and other data-intensive records can be stored economically and accessed in multiple locations more quickly than ever"
Which is it, "online access" or "nearline storage"?
If a client asked why slower drives consume less energy or generate less heat, I could explain that, but if they ask why slower drives must have SATA connections, that is a different discussion. The speed of a drive and its connection technology are for the most part independent. A 10K RPM drive can be made with FC, SAS or SATA connection.
I am opposed to using "Nearlne" just to distinguish between four-digit speeds (such as 5400 or 7200 RPM) versus "online" for five-digit speeds (10,000 and 15,000 RPM). The difference in performance between 10K RPM and 7200 RPM spinning disks is miniscule compared to the differences between solid-state drives and any spinning disk, or the difference between spinning disk and tape.
I am also opposed to using the term "Nearline" for online storage systems just because they are targeted for the typical use cases like backup, archive or other reference information that were previously directed to nearline devices like automated tape libraries.
Can we all just agree to refer to drives as "fast" or "slow", or give them RPM rotational speed designations, rather than try to incorrectly imply that FC and SAS drives are always fast, and SATA drives are always slow? Certainly we don't need new terms like "NL-SAS" just to represent a slower SAS connected drive.
If you store your VMware bits on external SAN or NAS-based disk storage systems, this post is for you. The subject of the post, VM Volumes, is a potential storage management game changer!
Fellow blogger Stephen Foskett mentioned VM Volumes in his [Introducing VMware vSphere Storage Features] presentation at IBM Edge 2012 conference. His session on VMware's storage features included VMware APIs for Array Integration (VAAI), VMware Array Storage Awareness (VASA), vCenter plug-ins, and a new concept he called "vVol", now more formally known as VM Volumes. This post provides a follow-up to this, describing the VM Volumes concepts, architecture, and value proposition.
"VM Volumes" is a future architecture that VMware is developing in collaboration with IBM and other major storage system vendors. So far, very little information about VM Volumes has been released. At VMworld 2012 Barcelona, VMware highlights VM Volumes for the first time and IBM demonstrates VM Volumes with the IBM XIV Storage System (more about this demo below). VM Volumes is worth your attention -- when it becomes generally available, everyone using storage arrays will have to reconsider their storage management practices in a VMware environment -- no exaggeration!
But enough drama. What is this all about?
(Note: for the sake of clarity, this post refers to block storage only. However, the VM Volumes feature applies to NAS systems as well. Special thanks to Yossi Siles and the XIV development team for their help on this post!)
The VM Volumes concept is simple: VM disks are mapped directly to special volumes on a storage array system, as opposed to storing VMDK files on a vSphere datastore.
The following images illustrate the differences between the two storage management paradigms.
You may still be asking yourself: bottom line, how will I benefit from VM Volumes?
Well, take a VM snapshot for example. With VM Volumes, vSphere can simply offload the operation by invoking a hardware snapshot of the hardware volume. This has significant implications:
VM-Granularity: Only the right VMs are copied (with datastores, backing up or cloning individual-VM portions of hardware snapshot of a datastore would require more complex configuration, tools and work)
Hardware Offload: No ESXi server resources are consumed
XIV advantage: With XIV, snapshots consume no space upfront and are completed instantly.
Here's the first takeaway: With VM Volumes, advanced storage services (which cost a lot when you buy a storage array), will become available at an individual VM level. In a cloud world, this means that applications can be provisioned easily with advanced storage services, such as snapshots and mirroring.
Now, let's take a closer look at another relevant scenario where VM Volumes will make a lot of difference - provisioning an application with special mirroring requirements:
VM Volumes case: The application is ordered via the private cloud portal. The requestor checks a box requesting an asynchronous mirror. He changes the default RPO for his needs. When the request is submitted, the process wraps up automatically: Volumes are created on one of the storage arrays, configured with a mirror and RPO exactly as specified. A few minutes later, the requestor receives an automatic mail pointing to the application virtual machine.
Datastores case #1: As may be expected, a datastore that is mirrored with the special RPO does not exist. As a result, the automated workflow sets a pending status on the request, creates an urgent ticket to a VMware administrator and aborts. When the VMware admin handles that ticket, she re-assigns the ticket to the storage administrator, asking for a new volume which is mirrored with the special RPO, and mapped to the right ESXi cluster. The next day, the volume is created; the ticket is re-assigned to the storage admin, with the new LUN being pointed to. The VMware administrator follows and creates the datastore on top of it. Since the automated workflow was aborted, the admin re-assigns the ticket to the cloud administrator, who sometime later completes the application provisioning manually.
Datastores case #2: Luckily for the requestor, a datastore that is mirrored with the special RPO does exist. However, that particular datastore is consuming space from a high performance XIV Gen3 system with SSD caching, while the application does not require that level of performance, so the workflow requires a storage administrator approval. The approval is given to save time, but the storage administrator opens a ticket for himself to create a new volume on another array, as well as a follow-up ticket for the VMware admin to create a new datastore using the new volume and migrate the application to the other datastore. In this case, provisioning was relatively rapid, but required manual follow up, involving the two administrators.
Here's the second takeaway: With VM Volumes, management is simplified, and end-to-end automation is much more applicable. The reason is that there are no datastores. Datastores physically group VMs that may otherwise be totally unrelated, and require close coordination between storage and VMware administrators.
Now, the above mainly focuses on the VMware or cloud administrator perspective. How does VM Volumes impact storage management?
VM's are the new hosts: Today, storage administrators have visibility of physical hosts in their management environment. In a non-virtualized environment, this visibility is very helpful. The storage administrator knows exactly which applications in a data center are storage-provisioned or affected by storage management operations because the applications are running on well-known hosts. However, in virtualized environments the association of an application to a physical host is temporary. To keep at least the same level of visibility as in physical environments, VMs should become part of the storage management environment, like hosts. Hosts are still interesting, for example to manage physical storage mapping, but without VM visibility, storage administrators will know less about their operation than they are used to, or need to. VM Volumes enables such visibility, because volumes are provided to individual VMs. The XIV VM Volumes demonstration at VMworld Barcelona, although experimental, shows a view of VM volumes, in XIV's management GUI.
Here's a screenshot:
That's not all!
Storage Profiles and Storage Containers: A Storage Profile is a vSphere specification of a set of storage services. A storage profile can include properties like thin or thick provisioning, mirroring definition, snapshot policy, minimum IOPS, etc.
Storage administrators define a portfolio of supported storage services, maintained as a set of storage profiles, and published (via VASA integration) to vSphere.
VMware or cloud administrators define the required storage profiles for specific applications
VMware and storage administrators need to coordinate the typical storage requirements and the automatically-available storage services. When a request to provision an application is made, the associated storage profiles are matched against the published set of available storage profiles. The matching published profiles will be used to create volumes, which will be bound to the application VMs. All that will happen automatically.
Note that when a VM is created today, a datastore must be specified. With VM Volumes, a new management entity called Storage Container (also known as Capacity Pool) replaces the use of datastore as a management object. Each Storage Container exposes a subset of the available storage profiles, as appropriate. The storage container also has a capacity quota.
Here are some more takeaways:
New way to interface vSphere and storage management: Storage administrators structure and publish storage services to vSphere via storage profiles and storage containers.
Automated provisioning, out of the box: The provisioning process automatically matches application-required storage profiles against storage profiles available from the specified storage containers. There is no need to build custom scripts and custom processes to automate storage provisioning to applications
The XIV advantage:
XIV services are very simple to define and publish. The typical number of available storage profiles would be low. It would also be easy to define application storage profiles.
XIV provides consistent high performance, up to very high capacity utilization levels, without any maintenance. As a result, automated provisioning (which inherently implies less human attention) will not create an elevated risk of reduced performance.
Note: A storage vendor VASA provider is required to support VM Volumes, storage profiles, storage containers and automated provisioning. The IBM Storage VASA provider runs as a standalone service that needs to be deployed on a server.
To summarize the VM Volumes value proposition:
Streamline cloud operation by providing storage services at VM and application level, enabling end-to-end provisioning automation, and unifying VMware and storage administration around volumes and VMs.
Increase storage array ROI, improve vSphere scalability and response time, and reduce cloud provisioning lag, by offloading VM-level provisioning, failover, backup, storage migration, storage space recycling, monitoring, and more, to the storage array, using advanced storage operations such as mirroring and snapshots.
Simplify the adoption of VM Volumes using XIV, with smaller and simpler sets of storage profiles. Apply XIV's supreme fast cloning to individual VMs, and keep automation risks at bay with XIV's consistent high performance.
Until you can get your hands on a VM Volumes-capable environment, the VMware and IBM developer groups will be collaborating and working hard to realize this game-changing feature. The above information is definitely expected to trigger your questions or comments, and our development teams are eager to learn from them and respond. Enter your comments below, and I will try to answer them, and help shape the next post on this subject. There's much more to be told.
Here I am, day 11 of a 17-day business trip, on my last leg of the trip this week, in Kuala Lumpur in Malaysia. I have been flooded with requests to give my take on EMC's latest re-interpretation of storage virtualization, VPLEX.
I'll leave it to my fellow IBM master inventor Barry Whyte to cover the detailed technical side-by-side comparison. Instead, I will focus on the business side of things, using Simon Sinek's Why-How-What sequence. Here is a [TED video] from Garr Reynold's post
[The importance of starting from Why].
Let's start with the problem we are trying to solve.
Problem: migration from old gear to new gear, old technology to new technology, from one vendor to another vendor, is disruptive, time-consuming and painful.
Given that IT storage is typically replaced every 3-5 years, then pretty much every company with an internal IT department has this problem, the exception being those companies that don't last that long, and those that use public cloud solutions. IT storage can be expensive, so companies would like their new purchases to be fully utilized on day 1, and be completely empty on day 1500 when the lease expires. I have spoken to clients who have spent 6-9 months planning for the replacement or removal of a storage array.
A solution to make the data migration non-disruptive would benefit the clients (make it easier for their IT staff to keep their data center modern and current) as well as the vendors (reduce the obstacle of selling and deploying new features and functions). Storage virtualization can be employed to help solve this problem. I define virtualization as "technology that makes one set of resources look and feel like a different set of resources, preferably with more desirable characteristics.". By making different storage resources, old and new, look and feel like a single type of resource, migration can be performed without disrupting applications.
Before VPLEX, here is a breakdown of each solution:
Non-disruptive tech refresh, and a unified platform to provide management and functionality across heterogeneous storage.
Non-disruptive tech refresh, and a unified platform to provide management and functionality between internal tier-1 HDS storage, and external tier-2 heterogeneous storage.
Non-disruptive tech refresh, with unified multi-pathing driver that allows host attachment of heterogeneous storage.
New in-band storage virtualization device
Add in-band storage virtualization to existing storage array
New out-of-band storage virtualization device with new "smart" SAN switches
SAN Volume Controller
HDS USP-V and USP-VM
For IBM, the motivation was clear: Protect customers existing investment in older storage arrays and introduce new IBM storage with a solution that allows both to be managed with a single set of interfaces and provide a common set of functionality, improving capacity utilization and availability. IBM SAN Volume Controller eliminated vendor lock-in, providing clients choice in multi-pathing driver, and allowing any-to-any migration and copy services. For example, IBM SVC can be used to help migrate data from an old HDS USP-V to a new HDS USP-V.
With EMC, however, the motivation appeared to protect software revenues from their PowerPath multi-pathing driver, TimeFinder and SRDF copy services. Back in 2005, when EMC Invista was first announced, these three software represented 60 percent of EMC's bottom-line profit. (Ok, I made that last part up, but you get my point! EMC charges a lot for these.)
Back in 2006, fellow blogger Chuck Hollis (EMC) suggested that SVC was just a [bump in the wire] which could not possibly improve performance of existing disk arrays. IBM showed clients that putting cache(SVC) in front of other cache(back end devices) does indeed improve performance, in the same way that multi-core processors successfully use L1/L2/L3 cache. Now, EMC is claiming their cache-based VPLEX improves performance of back-end disk. My how EMC's story has changed!
So now, EMC announces VPLEX, which sports a blend of SVC-like and Invista-like characteristics. Based on blogs, tweets and publicly available materials I found on EMC's website, I have been able to determine the following comparison table. (Of course, VPLEX is not yet generally available, so what is eventually delivered may differ.)
Scalable, 1 to 4 node-pairs
One size fits all, single pair of CPCs
SVC-like, 1 to 4 director-pairs
Works with any SAN switches or directors
Required special "smart" switches (vendor lock-in)
SVC-like, works with any SAN switches or directors
Broad selection of IBM Subsystem Device Driver (SDD) offered at no additional charge, as well as OS-native drivers Windows MPIO, AIX MPIO, Solaris MPxIO, HP-UX PV-Links, VMware MPP, Linux DM-MP, and comercial third-party driver Symantec DMP.
Limited selection, with focus on priced PowerPath driver
Invista-like, PowerPath and Windows MPIO
Read cache, and choice of fast-write or write-through cache, offering the ability to improve performance.
No cache, Split-Path architecture cracked open Fibre Channel packets in flight, delayed every IO by 20 nanoseconds, and redirected modified packets to the appropriate physical device.
SVC-like, Read and write-through cache, offering the ability to improve performance.
Space-Efficient Point-in-Time copies
SVC FlashCopy supports up to 256 space-efficient targets, copies of copies, read-only or writeable, and incremental persistent pairs.
Like Invista, No
Remote distance mirror
Choice of SVC Metro Mirror (synchronous up to 300km) and Global Mirror (asynchronous), or use the functionality of the back-end storage arrays
No native support, use functionality of back-end storage arrays, or purchase separate product called EMC RecoverPoint to cover this lack of functionality
Limited synchronous remote-distance mirror within VPLEX (up to 100km only), no native asynchronous support, use functionality of back-end storage arrays
Provides thin provisioning to devices that don't offer this natively
Like Invista, No
SVC Split-Cluster allows concurrent read/write access of data to be accessed from hosts at two different locations several miles apart
I don't think so
PLEX-Metro, similar in concept but implemented differently
Non-disruptive tech refresh
Can upgrade or replace storage arrays, SAN switches, and even the SVC nodes software AND hardware themselves, non-disruptively
Tech refresh for storage arrays, but not for Invista CPCs
Tech refresh of back end devices, and upgrade of VPLEX software, non-disruptively. Not clear if VPLEX engines themselves can be upgraded non-disruptively like the SVC.
Heterogeneous Storage Support
Broad support of over 140 different storage models from all major vendors, including all CLARiiON, Symmetrix and VMAX from EMC, and storage from many smaller startups you may not have heard of
Invista-like. VPLEX claims to support a variety of arrays from a variety of vendors, but as far as I can find, only DS8000 supported from the list of IBM devices. Fellow blogger Barry Burke (EMC) suggests [putting SVC between VPLEX and third party storage devices] to get the heterogeneous coverage most companies demand.
Back-end storage requirement
Must define quorum disks on any IBM or non-IBM back end storage array. SVC can run entirely on non-IBM storage arrays
HP SVSP-like, requires at least one EMC storage array to hold metadata
SVC 2145-CF8 model supports up to four solid-state drives (SSD) per node that can treated as managed disk to store end-user data
Invista-like. VPLEX has an internal 30GB SSD, but this is used only for operating system and logs, not for end-user data.
In-band virtualization solutions from IBM and HDS dominate the market. Being able to migrate data from old devices to new ones non-disruptively turned out to be only the [tip of the iceberg] of benefits from storage virtualization. In today's highly virtualized server environment, being able to non-disruptively migrate data comes in handy all the time. SVC is one of the best storage solutions for VMware, Hyper-V, XEN and PowerVM environments. EMC watched and learned in the shadows, taking notes of what people like about the SVC, and decided to follow IBM's time-tested leadership to provide a similar offering.
EMC re-invented the wheel, and it is round. On a scale from Invista (zero) to SVC (ten), I give EMC's new VPLEX a six.
My series last week on IBM Watson (which you can read [here], [here], [here], and [here]) brought attention to IBM's Scale-Out Network Attached Storage [SONAS]. IBM Watson used a customized version of SONAS technology for its internal storage, and like most of the components of IBM Watson, IBM SONAS is commercially available as a stand-alone product.
Like many IBM products, SONAS has gone through various name changes. First introduced by Linda Sanford at an IBM SHARE conference in 2000 under the IBM Research codename Storage Tank, it was then delivered as a software-only offering SAN File System, then as a services offering Scale-out File Services (SoFS), and now as an integrated system appliance, SONAS, in IBM's Cloud Services and Systems portfolio.
If you are not familiar with SONAS, here are a few of my previous posts that go into more detail:
This week, IBM announces that SONAS has set a world record benchmark for performance, [a whopping 403,326 IOPS for a single file system]. The results are based on comparisons of publicly available information from Standard Performance Evaluation Corporation [SPEC], a prominent performance standardization organization with more than 60 member companies. SPEC publishes hundreds of different performance results each quarter covering a wide range of system performance disciplines (CPU, memory, power, and many more). SPECsfs2008_nfs.v3 is the industry-standard benchmark for NAS systems using the NFS protocol.
(Disclaimer: Your mileage may vary. As with any performance benchmark, the SPECsfs benchmark does not replicate any single workload or particular application. Rather, it encapsulates scores of typical activities on a NAS storage system. SPECsfs is based on a compilation of workload data submitted to the SPEC organization, aggregated from tens of thousands of fileservers, using a wide variety of environments and applications. As a result, it is comprised of typical workloads and with typical proportions of data and metadata use as seen in real production environments.)
The configuration tested involves SONAS Release 1.2 on 10 Interface Nodes and 8 Storage Pods, resulting a single file system over 900TB usable capacity.
10 Interface Nodes; each with:
Maximum 144 GB of memory
One active 10GbE port
8 Storage Pods; each with:
2 Storage nodes and 240 drives
Drive type: 15K RPM SAS hard drives
Data Protection using RAID-5 (8+P) ranks
Six spare drives per Storage Pod
IBM wanted a realistic "no compromises" configuration to be tested, by choosing:
Regular 15K RPM SAS drives, rather than a silly configuration full of super-expensive Solid State Drives (SSD) to plump up the results.
Moderate size, typical of what clients are asking for today. The Goldilocks rule applies. This SONAS is not a small configuration under 100TB, and nowhere close to the maximum supported configuration of 7,200 disks across 30 Interface Nodes and 30 Storage Pods.
Single file system, often referred to as a global name space, rather than using an aggregate of smaller file systems added together that would be more complicated to manage. Having multiple file systems often requires changes to applications to take advantage of the aggregate peformance. It is also more difficult to load-balance your performance and capacity across multiple file systems. Of course, SONAS can support up to 256 separate file systems if you have a business need for this complexity.
The results are stunning. IBM SONAS handled three times more workload for a single file system than the next leading contender. All of the major players are there as well, including NetApp, EMC and HP.
Continuing this week's coverage of IBM's 3Q announcements, today it's all about storage for our mainframe clients.
IBM System Storage DS8700
IBM is the leader in high-end disk attached to mainframes, with the IBM DS8700 being our latest model in a long series of successful products in this space. Here are some key features:
Full Disk Encryption (FDE), which I mentioned in my post [Different Meanings of the word "Protect"]. FDE are special 15K RPM Fibre Channel drives that include their own encryption chip, so that IBM DS8700 can encrypt the data at rest without impacting performance of reads or writes. The encryption keys are managed by IBM Tivoli Key Lifecycle Manager (TKLM).
Easy Tier, which I covered in my post [DS8700 Easy Tier Sub Lun Automatic Migration] which offers what EMC promised but has yet to deliver, the ability to have CKD volumes and FBA LUNs to straddle the fence between Solid State Drives (SSD) and spinning disk. For example, a 54GB CKD volume could have 4GB on SSD and the remaining 50GB on spinning drives. The hottest extents are moved automatically to SSD, and the coldest moved down to spinning disk. To learn more about Easy Tier, watch my [7-minute video] on IBM [Virtual Briefing Center].
z/OS Distributed Data Backup (zDDB), announced this week, provides the ability for a program running on z/OS to backup data written by distributed operating systems like Windows or UNIX stored in FBA format. In the past, to backup FBA LUNs involved a program like IBM Tivoli Storage Manager client to read the data natively, send it over Ethernet LAN to a TSM Server, which could run on the mainframe and use mainframe resources. This feature eliminates the Ethernet traffic by allowing a z/OS program to read the FBA blocks through standard FICON channels, which can then be written to z/OS disk or tape resources. Here is the [Announcement Letter] for more details.
One program that takes advantage of this new zDDB feature already is Innovation's [FDRSOS], which I pronounce "fudder sauce". If you are an existing FDRSOS customer, now is a good time to get rid of any EMC or HDS disk and replace with the new IBM DS8700 system.
IBM System Storage TS7680 ProtecTIER Deduplication Gateway for System z
When it comes to virtual tape libraries that attach to mainframes, the two main players are IBM TS7700 series and Oracle StorageTek Virtual Storage Manager (VSM). However, mainframe clients with StorageTek equipment are growing frustrated over Oracle's lack of commitment for mainframe-attachable storage. To make matters worse, Oracle recently missed a key delivery date for their latest enterprise tape drive.
What's new this week is that IBM now supports native IP-based asynchronous replication of virtual tapes at distance, from one TS7680 to another TS7680. This replaces the method of replication using the back end disk features. The problem with using disk replication is that all the virtual tapes will be copied over. Instead, the ProtecTIER administrator can decide which subset of virtual tapes should be replicated to the remote site, and that can reduce both storage requirements as well as bandwidth costs. See the [Announcement Letter] for more details.
This week I got a comment on my blog post [IBM Announces another SSD Disk offering!]. The exchange involved Solid State Disk storage inside the BladeCenter and System x server line. Sandeep offered his amazing performance results, but we have no way to get in contact with him. So, for those interested, I have posted on SlideShare.net a quick five-chart presentation on recent tests with various SSD offerings on the eX5 product line here:
Well, it's Tuesday, and you know what that means... IBM announcements!
In today's environment, clients expect more from their storage, and from their storage provider. The announcements span the gamut, from helping to use Business Analytics to analyze Big Data for trends, insights and patterns, to managing private, public and hybrid cloud environments, all with systems that are optimized for their particular workloads.
There are over a dozen different announcements, so I will split these up into separate posts. Here is part 1.
IBM Scale Out Network Attach Storage (SONAS) R1.3
I have covered [IBM SONAS] for quite some time now. Based on IBM's General Parallel File System (GPFS), this integrated system combines servers, storage and software into a fully functional scale-out NAS solution that support NFS, CIFS, FTP/SFTP, HTTP/HTTPS, and SCP protocols. IBM continues its technical leadership in the scale-out NAS marketplace with new hardware and software features.
The hardware adds new disk options, with 900GB SAS 15K RPM drives, and 3TB NL-SAS 7200 RPM drives. These come in 4U drawers of 60 drives each, six ranks of ten drives each. So, with the high-performance SAS drives that would be about 43TB usable capacity per drawer, and with the high-capacity NL-SAS drives about 144TB usable. You can have any mix of high-performance drawers and high-capacity drawers, up to 7200 drives, for a maximum usable capacity of 17PB usable (21PB for those who prefer it raw). This makes it the largest commercial scale-out NAS in the industry. This capacity can be made into one big file system, or divided up to 256 smaller file systems.
In addition to snapshots of each file system, you can divide the file system up into smaller tree branches and snapshot these independently as well. The tree branches are called fileset containers. Furthermore, you can now make writeable clones of individual files, which provides a space-efficient way to create copies for testing, training or whatever.
Performance is improved in many areas. The interface nodes now can support a second dual-port 10GbE, and replication performance is improved by 10x.
SONAS supports access-based enumeration, which means that if there are 100 different subdirectories, but you only have authority to access five of them, then that's all you see, those five directories. You don't even know the other 95 directories exist.
I saved the coolest feature for last, it is called Active Cloud Engine™ that offers both local and global file management. Locally, Active Cloud Engine placement rules to decide what type of disk a new file should be placed on. Management rules that will move the files from one disk type to another, or even migrates the data to tape or other externally-managed storage! A high-speed scan engine can rip through 10 million files per node, to identify files that need to be moved, backed up or expired.
Globally, Active Cloud Engine makes the global namespace truly global, allowing the file system to span multiple geographic locations. Built-in intelligence moves individual files to where they are closest to the users that use them most. This includes an intelligent push-over-WAN write cache, on-demand pull-from-WAN cache for reads, and will even pre-fetch subsets of files.
No other scale-out NAS solution from any other storage vendor offers this amazing and awesome capability!
IBM® Storwize® V7000
Last year, we introduced the [IBM Storwize V7000], a midrange disk system with block-level access via FCP and iSCSI protocols. The 2U-high control enclosure held two cannister nodes, a 12-drive or 24-drive bay, and a pair of power-supply/battery UPS modules. The controller could attach up to nine expansion enclosures for more capacity, as well as virtualize other storage systems. This has been one of our most successful products ever, selling over 100PB in the past 12 months to over 2,500 delighted customers.
The 12-drive enclosure now supports both 2TB and 3TB NL-SAS drives. The 24-drive enclosures support 200/300/400GB Solid-State Drives (SSD), 146 and 300GB 15K RPM drives, 300/450/600GB 10K RPM drives, and a new 1TB NL-SAS drive option. For those who want to set up "Flash-and-Stash" in a single 2U drawer, now you can combine SSD and NL-SAS in the 24-drive enclosure! This is the perfect platform for IBM's Easy Tier sub-LUN automated tiering. IBM's Easy Tier is substantially more powerful and easier to use than EMC's FAST-VP or HDS's Dynamic Tiering.
Last week, at Oracle OpenWorld, there were various vendors hawking their DRAM/SSD-only disk systems, including my friends at Texas Memory Systems, Pure Storage, and Violin Memory Systems. When people came to the IBM booth to ask what IBM offers, I explained that both the IBM DS8000 and the Storwize V7000 can be outfitted in this manner. With the Storwize V7000, you can buy as much or little SSD as you like. You do not have to buy these drives in groups of 8 or 16 at a time.
The Storwize V7000 is the sister product of the IBM SAN Volume Controller, so you can replicate between one and the other. I see two use cases for this. First, you might have a SVC at a primary location, and decide to replicate just the subset of mission-critical production data to a remote location, and use the Storwize V7000 as the target device. Secondly, you could have three remote or branch offices (ROBO) that replicate to a centralized data center SAN Volume Controller.
Lastly, like the SVC, the Storwize V7000 now supports clustering so that you can now combine multiple control enclosures together to make a single system.
IBM® Storwize® V7000 Unified
Do you remember how IBM combined the best of SAN Volume Controller, XIV and DS8000 RAID into the Storwize V7000? Well, IBM did it again, combining the best of the Storwize V7000 with the common NAS software base developed for SONAS into the new "Storwize V7000 Unified".
You can upgrade your block-only Storwize V7000 into a file-and-block "Storwize V7000 Unified" storage system. This is a 6U-high system, consisting of a pair of 2U-high file modules connected to a standard 2U-high control enclosure. Like the block-only version, the control enclosure can attach up to nine expansion enclosures, as well as all the same support to virtualize external disk systems. The file modules combine the management node, interface node and storage node functionality that SONAS R1.3 offers.
What exactly does that mean for you? In addition to FCP and iSCSI for block-level LUNs, you can carve out file systems that support NFS, CIFS, FTP/SFTP, HTTP/HTTPS, and SCP protocols. All the same support as SONAS for anti-virus checking, access-based enumeration, integrated TSM backup and HSM functionality to migrate data to tape, NDMP backup support for other backup software, and Active Cloud Engine's local file management are all included!
IBM SAN Volume Controller V6.3
The SAN Volume Controller [SVC] increases its stretched cluster to distances up to 300km. This is 3x further than EMC's VPLEX offering. This allows identical copies of data to be kept identical in both locations, and allows for Live Partition Mobility or VMware vMotion to move workloads seamlessly from one data center to another. Combining two data centers with an SVC stretch cluster is often referred to as "Data Center Federation".
The SVC also introduces a low-bandwidth option for Global Mirror. We actually borrowed this concept from our XIV disk system. Normally, SVC's Global Mirror will consume all the bandwidth it can to keep the destination copy of the data within a few seconds of currency behind the source copy. But do you always need to be that current? Can you afford the bandwidth requirements needed to keep up with that? If you answered "No!" to either of these, then the low-bandwidth option is you. Basically, a FlashCopy is done on the source copy, this copy is then sent over to the destination, and a FlashCopy is made of that. The process is then repeated on a scheduled basis, like every four hours. This greatly reduces the amount of bandwidth required, and for many workloads, having currency in hours, rather than seconds, is good enough.
I am very excited about all these announcements! It is a good time to be working for IBM, and look forward to sharing these exciting enhancements with clients at the Tucson EBC.
Well, it's Tuesday again, and you know what that means! IBM Announcements! Typically, IBM System Storage has three to five major product launches per year. Making announcements every Tuesday would have been two frequent, and having one big announcement every two or three years would be too far apart. Worldwide combined revenues for storage hardware and software grew double digits last year, comparing full-year 2011 to the prior 2010 year, and I am sure that 2012 will also be a good year for IBM as well! This week we have announcements for both disk and tape, but since 2012 is the 60th Diamond Anniversary for tape, I will start with tape systems first.
TS1140 support for JA/JJ tape cartridges
The TS1140 enterprise tape drive was announced at the [Storage Innovation Executive Summit] last May. It supported a new E07 format on three different new tape cartridges. Models "JC" was 4.0TB standard re-writeable tapes, "JY" was 4.0TB WORM tapes, and "JK" were 500GB economy tapes that were less expensive, but offered faster random access.
Generally, IBM has adopted an N-2 read, N-1 write [backward compatibility]. This means that the TS1140 could read E05 and E06 formatted tapes on JB and JX media, and could write E06 format on JB and JX media. However, there are a lot of older JA and JJ media, especially as part of TS7740 environments, so IBM now supports TS1140 drives to read J1A formatted JA and JJ media. This is not just for TS7740 environments, any TS1140 in stand-alone or tape library configurations will support this as well.
TS7700 R2.1 enhancements
IBM is a leader in tape virtualization with or without physical tape as back-end media. There are two hardware models of the [IBM Virtualization Engine TS7700 family] for the IBM System z mainframe. These virtual libraries are referred to as "clusters" in IBM literature.
The TS7740 Virtual Tape Library supports putting virtual tape images on disk first, then move less-active data to physical tape, which I covered in my blog post [IBM Announcements - July 2007].
A unique feature of the TS7700 series is support for a Grid configuration, which allows up to six different TS7700 clusters to be grouped into a single instance image. These clusters can be in local or remote locations, connected via WAN or LAN connections.
R2.1 is the latest software release of this successful IBM's TS7700 series.
True Sync Mode Copy. Before R2.1, the TS7700 offered "immediate mode copy". An application would write to a virtual tape, and when it was done with the tape and performed an unmount, the TS7700 would then replicate the tape contents to a secondary cluster on the grid. With True Sync Mode, data contents are replicated per implicit or explicit SYNC points. This is another IBM first in the IT tape industry.
Remote Mount Fail-over. When you have two or more TS7700 clusters in a grid configuration, you can do remote mounts. We've added fail-over multi-pathing up to four paths, so that if a link to a remote cluster is down, it will try one of the others instead.
Parallel Copies and Pre-Migration. On of my 19 patents is for the pre-migration feature for the IBM 3494 Virtual Tape Server (VTS) that carries forward into the TS7700, and is also used in the SONAS and Information Archive products. However, when the grid architecture was introduced, the engineers decided not to allow pre-migration and copies to secondary clusters to occur concurrently. Now these two operations can be done in parallel.
Merge two grids into one grid. Now that we can support up to six clusters into a single grid, we have people with 2-cluster and 3-cluster grids looking to merge them into one. Of course, all the logical and physical volume serials (VOLSER) must be unique!
Accelerate off JA/JJ Media. There are a lot of older JA and JJ media still in TS7700 libraries. This feature allows customers to speed up the transition to newer physical tape media.
Copy Export to E06 format on JB media. This one is clever, and I have to say I would have never thought about it. Let's say you have a TS7740 with TS1140 drives, but you want to export some virtual tapes to physical media to be sent to someone who only has a TS7740 connected with older TS1130 drives. These older drives can't read new JC media nor make sense of the E07 format. This feature will let you export to older JB media in E06 format so that it will be fully readable at the new location on the TS1130 drives.
Copy Export Merge service offering. Thanks to mergers and acquisitions, it is sometimes necessary to split off a portion of data from a TS7700 grid. In the past, IBM supported sending this export to a completely empty TS7700 library, but this new service offerings allows the export to be merged into an existing TS7700 that already contains data.
LTFS-SDE support for Mac OS X 10.7 Lion
How do people still not yet know about the Linear Tape File System [LTFS]? I mentioned this in my blogs back in 2010 in [April], [September], and [November]. Last year, LTFS was the [NAB Show Pick Hits Award] and an [Emmy] for revolutionizing the use of digital tape in Television broadcasting.
In layman's terms, the Single Drive Edition [LTFS-SDE] allows a tape cartridge to be treated like USB memory stick. It is supported on the LTO5 tape drives for systems running various levels of Windows, Linux and Mac OS X. Prior to this announcement, IBM supported Snow Leopard (10.5.6) and Leopard (10.6), and now supports Mac OS X 10.7 "Lion" release.
IBM first introduced Solid-State Drives (SSD) back in 2007 where it made sense the most, in [drive-for-drive replacements on blade servers in the IBM BladeCenter]. Blade servers typically only have a single drive, and SSD are both faster and use less energy on a drive-for-drive comparison, so this provided immediate benefit. Today, SSD are available on a variety of System x and POWER system servers.
In 2008, IBM rocked the world by being the first to reach [1 Million IOPS with Project Quicksilver]. This was an all-SSD configuration which many considered unrealistic (at the time), but it showed the potential for solid state drives.
When the [XIV Gen3 was Announced - July 2011], each module included an 1.8-inch "SSD-Ready" slot in the back. IBM made a Statement of Direction that IBM would someday offer SSD drives to put in these slots. Today's announcement is that IBM has finalized the qualification process, so now XIV Gen3 clients can have 400GB of usable non-volatile SSD read cache added to each module. This SSD can be added to existing XIV Gen3 boxes in the field, or it can be factory-installed in new shipments. If you have a 15-module XIV, that's 6TB of additional read cache! This SSD is entirely managed by the XIV Gen3, so you won't have to spend weeks reading manuals or specifying configuration parameters.
When you carve volumes on the XIV, you now have an option to enable or disable use of the SSD cache for each volume. Since XIV is being used in private and public cloud deployments, this offers the ability to offer premium performance at premium prices. The use of SSD is complementary to IBM XIV Quality of Service (QoS) performance levels, which are determined by host instead.
Well, that's the first major IBM System Storage launch of 2012. Let me know what you think in the comment section below.
Continuing my week in Washington DC for the annual [2010 System Storage Technical University], I presented a session on Storage for the Green Data Center, and attended a System x session on Greening the Data Center. Since they were related, I thought I would cover both in this post.
Storage for the Green Data Center
I presented this topic in four general categories:
Drivers and Metrics - I explained the three key drivers for consuming less energy, and the two key metrics: Power Usage Effectiveness (PUE) and Data Center Infrastructure Efficiency (DCiE).
Storage Technologies - I compared the four key storage media types: Solid State Drives (SSD), high-speed (15K RPM) FC and SAS hard disk, slower (7200 RPM) SATA disk, and tape. I had comparison slides that showed how IBM disk was more energy efficient than competition, for example DS8700 consumes less energy than EMC Symmetrix when compared with the exact same number and type of physical drives. Likewise, IBM LTO-5 and TS1130 tape drives consume less energy than comparable HP or Oracle/Sun tape drives.
Integrated Systems - IBM combines multiple storage tiers in a set of integrated systems managed by smart software. For example, the IBM DS8700 offers [Easy Tier] to offer smart data placement and movement across Solid-State drives and spinning disk. I also covered several blended disk-and-tape solutions, such as the Information Archive and SONAS.
Actions and Next Steps - I wrapped up the talk with actions that data center managers can take to help them be more energy efficient, from deploying the IBM Rear Door Heat Exchanger, or improving the management of their data.
Greening of the Data Center
Janet Beaver, IBM Senior Manager of Americas Group facilities for Infrastructure and Facilities, presented on IBM's success in becoming more energy efficient. The price of electricity has gone up 10 percent per year, and in some locations, 30 percent. For every 1 Watt used by IT equipment, there are an additional 27 Watts for power, cooling and other uses to keep the IT equipment comfortable. At IBM, data centers represent only 6 percent of total floor space, but 45 percent of all energy consumption. Janet covered two specific data centers, Boulder and Raleigh.
At Boulder, IBM keeps 48 hours reserve of gasoline (to generate electricity in case of outage from the power company) and 48 hours of chilled water. Many power outages are less than 10 minutes, which can easily be handled by the UPS systems. At least 25 percent of the Computer Room Air Conditioners (CRAC) are also on UPS as well, so that there is some cooling during those minutes, within the ASHRAE guidelines of 72-80 degrees Fahrenheit. Since gasoline gets stale, IBM runs the generators once a month, which serves as a monthly test of the system, and clears out the lines to make room for fresh fuel.
The IBM Boulder data center is the largest in the company: 300,000 square feet (the equivalent of five football fields)! Because of its location in Colorado, IBM enjoys "free cooling" using outside air temperature 63 percent of the year, resulting in a PUE of 1.3 rating. Electricity is only 4.5 US cents per kWh. The center also uses 1 Million KwH per year of wind energy.
The Raleigh data center is only 100,000 Square feet, with a PUE 1.4 rating. The Raleigh area enjoys 44 percent "free cooling" and electricity costs at 5.7 US cents per kWh. The Leadership in Energy and Environmental Design [LEED] has been updated to certify data centers. The IBM Boulder data center has achieved LEED Silver certification, and IBM Raleigh data center has LEED Gold certification.
Free cooling, electricity costs, and disaster susceptibility are just three of the 25 criteria IBM uses to locate its data centers. In addition to the 7 data centers it manages for its own operations, and 5 data centers for web hosting, IBM manages over 400 data centers of other clients.
It seems that Green IT initiatives are more important to the storage-oriented attendees than the x86-oriented folks. I suspect that is because many System x servers are deployed in small and medium businesses that do not have data centers, per se.