Tony Pearson is a Master Inventor and Senior IT Architect for the IBM Storage product line at the
IBM Systems Client Experience Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services.
(Short URL for this blog: ibm.co/Pearson )
My books are available on Lulu.com! Order your copies today!
Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
I was warned that this musical would be nearly three hours long, that the singing and dialogue would be in Hindi language, and there would be no English subtitles. I don't speak Hindi, and would not be able to understand a single word the actors said.
How bad could it be?
Despite the fact that there were nearly 20 members in the cast, the story jumps back and forth in both place and time, with some dream sequences thrown in for cinematic effect, I was able to understand quite a bit. I thoroughly enjoyed this movie! Perhaps its a sign of a good movie that you can understand most of it purely from the visual aspects.
The same can be said for presentations that you give in foreign countries. Both in Japan and India, I had plenty of visuals to complement the text on the page, and the words that I spoke. Shawn over at [Anecdote] blog points to this greatpresentation by Garr Reynolds, author of [Presentation Zen]. The slide deck below has some key takeaways and quotes from Dr. John Medina's latest book "Brain Rules" that apply to presentations.
We have successfully arrived to Mumbai, India. Since this is my first time in India, I decidedto check out the town by going to the local McDonald's® restaurant. As a former software engineer of McDonald's, I love the food, and try to visit a McDonald's in every country I visit. Wikipedia calls our transportation an [Auto Rickshaw], but the locals called it a "tuk-tuk". This is not my first time in one, they have them in Thailand and Mexico as well.
We had the hotel identify the address of the closest McDonald's to our hotel. From past experienceI know that tuk-tuk drivers will suggest alternatives, in an effort to earn a larger fare, or to redirectto a preferred location where the driver might get special kick-backs. Our driver was no different.
The traffic was treacherous, the roadswere in roughshod condition, and sad looking stray dogs digging through piles of rubbish were everywhere. The local "Daily News and Analysis" newspaper this week estimates that there are over 70,000 stray dogs in Mumbai alone.What to do with all of these strays is a matter of controversy. In preparation for the Olympic games, China hasasked its restaurants to [take"dog" off their menus].Having lived in one of the poorest countries, and one of the richest, nothing surprises me anymore.
My IBM colleague, Curtis Neal, decided to join me for this adventure. Finally, after about 20 minutes, our driver parks the tuk-tuk. He told us the restaurant is only aboutthree blocks away by foot, he would allow us to treat him to lunch, and then he will take us back to the hotel.While we appreciated his fantastic imagination, we told him we just wanted to be taken one-way to the restaurant, to drop us off at the front door, and we would find another tuk-tuk for the return.
After a bit of argument, we settled on being left only one block away, and we would walk the rest.While we could not see exactly where the restaurant was when we got out, he at least pointed us in the right direction.
The problem was that we approached the restaurant from behind, and came up to its equivalent of a "drive thru" window,ordered our food, and then went to the second window to pick up our order. We were eating on the street. It was not until I decided to take this photo of the restaurant, that we discovered there was an entire seating area upstairs, and around the cornerthe main entrance!
There were plenty of tuk-tuks picking up and dropping people off, so we have no idea why ourprevious driver was unwilling to take us the entire distance.
Cows are sacred here in India, so thereare no beef-based hamburgers to choose from. My choices for sandwiches were:
Since my nutritionist asked me to avoid carbs and fried foods, I chose the McChicken with cheese combo meal with fries and a Coke.
Getting back was also a challenge. While we had no problem haling a tuk-tuk, we had no idea the address of ourhotel, and our driver had no idea where it was. We ended up driving around the city until we found a differenthotel, asked them if they knew where it was, and then eventually getting to our hotel. This is something I shouldhave planned for in advance, getting a card with the hotel details on it before leaving.
While it might seem like a simple trip, Curtis and I probably learned more about India this way than spending a week inside the comforts of our hotel.
A faithful reader of this blog, Tom, sent me a link to Orson Scott Card's article titled[PROGRAMMERS AS BEES (or, how to kill a software company)]. "Is there any truth in this?" Tom asked?Having worked both sides of this fence as I approach my 22 year anniversary at IBM, I guess I can venturesome opinions on this piece. Let's start with this excerpt:
"The environment that nurtures creative programmers kills management and marketing types - and vice versa."
By this, he means "kills" in the UNIX sense, I imagine, and not the "Grand Theft Auto IV" sense.Different people solve problems differently. Some programmers have the luxury that theycan often focus on a single platform, single chipset, single OS, and so on, but Marketing types are tryingto come up with messaging that appeals to a broad audience, from people with business backgrounds to others with moretechnical backgrounds, and that can be more challenging. For programmers, "creative" is an adjective; formarketers, it's a noun.
"Programming is the Great Game. It consumes you, body and soul. When you're caught up in it, nothing else matters."
True. As a storage consultant, I find myself writing code a lot, from small programs, scripts, and even HTML codefor this blog. When you are in your zone, working on something, one can easily lose track of time.
"Here's the secret that every successful software company is based on: You can domesticate programmers the way beekeepers tame bees. You can't exactly communicate with them, but you can get them to swarm in one place and when they're not looking, you can carry off the honey. You keep these bees from stinging by paying them money. More money than they know what to do with. But that's less than you might think."
I have never tamed bees, but many of my friends who are still programmers are motivated by factors other thanmaximizing their income, such as: friendly co-workers, job security, casual attire, and interesting challenges. A few make more than they know what to do with, the rest have girlfriends"significant others" who solve that problem for them.
"One way or another, marketers get control. But...control of what? Instead of finding assembly lines of productive workers, they quickly discover that their product is produced by utterly unpredictable, uncooperative, disobedient, and worst of all, unattractive people who resist all attempts at management."
False. Either marketing had control in the first place (ala Apple, Inc.) or they never had. "Control of what?" is the key phrase here.
"The shock is greater for the coder, though. He suddenly finds that alien creatures control his life. Meetings, Schedules, Reports. And now someone demands that he PLAN all his programming and then stick to the plan, never improving, never tweaking, and never, never touching some other team's code."
True. But if you don't like surprises, perhaps software engineering is not the right career path for you.
"The hive has been ruined. The best coders leave. And the marketers, comfortable now because they're surrounded by power neckties and they have things under control, are baffled that each new iteration of their software loses market share as the code bloats and the bugs proliferate. Got to get some better packaging. Yeah, that's it."
This one depends. I've seen teams survive and manage, with junior programmers stepping up to backfill leadership roles, and other times, projects are scrapped, or started anew elsewhere. As for marketers, it doesn't take much to get one baffled, does it?
I'm glad this is the final day of the IBM Systems Technical Conference (STC08) here in Los Angeles.While I enjoyed the conference, one quickly reaches saturation point with all the information presented.
XIV Architecture Overview
Before this conference, many of the attendees didn't understandIBM's strategy, didn't understand Web 2.0 and Digital archive workloads,and didn't understand why IBM acquired XIV to offer "yet another disk systemthat servers LUNs to distributed server platforms." Brian Shermanchanged all that!
Brian Sherman, IBM Advanced Technical Support (ATS), is part of the exclusive dedicated XIVtechnical team to install these boxes at client locations, so he is very knowledgeable with the technical aspects of the architecture. He presented what the current XIV-branded model that clients can purchase now in select countries, and what the IBM-branded model will change when available worldwide.
Those who missed my earlier series on XIV can find them here:
Beyond this, Brian gave additional information on how thin provisioning, storage pools, disk mirroring, consistency groups, management consoles, and microcode updates are implemented.
N series and VMware Deep Dive
Norm Bogard, IBM Advanced Technical Support, presented why the IBM N series makes such great disk storage for VMware
deployments. This wasclearly labeled as a "deep dive", so anyone who got lost in all of theacronyms could not blame Norm for misrepresentation.
IBM has been doing server virtualization for over 40 years, so it makes sense thatit happens to be the number one reseller of VMware offerings.VMware ESX server is a hypervisor that runs on x86 host, and provides an emulationlayer for "guest Operating Systems". Each guest can hvae one or more virtualdisks, which are represented by VMware as VMDK files. VMware ESX server acceptsread/write requests from the guests, and forwards them on to physical storage.Many of VMware's most exciting features requires storage to be external to thehost machine. [VMotion]allows guests to move from one host to another, [Distributed Resource Scheduler (DRS)]allows a set of hosts to load-balance the guestsacross the hosts, and [High Availability (HA)] allows the guests on a failed hostto be resurrected on a surviving host. All of these require external disk storage.
ESX server allows up to 256 LUNs, attached via FCP and/or iSCSI, and up to 32 NFS mount points. Across LUNs, ESX server uses VMFS file system, which is a clusteredfile system like IBM GPFS that allows multiple hosts to access the same LUNs.ESX server has its own built-in native multipathing driver, and even provides FCP-iSCSIand iSCSI multipathing. In other words, you can have a LUN on an IBM System Storage N series thatis attached over both FCP and iSCSI, so if the SAN switch or HBA fails, ESX servercan failover to the iSCSI connection.
ESX server can use NFS protocol to access the VMDK files instead. While the default is only 8 NFS mount points, you can increase this to 32 mount points. NAS can takeadvantage of Link Aggregate Control Protocol [LACP] groups, what some call "trunking" or "EtherChannel". This is the ability to consolidate multiple streams onto fewer inter-switch Ethernet links, similar to what happens on SAN switches.For the IBM N series, IBM recommends a "fixed" path policy, rather than "most recently used".
IBM recommends disabling SnapShot schedules, and setting the Snap reserve to 0 percent.Why? A snapshot of an ESX server datastore has the VMDK files of many guests, all of which would have had to quiesce or stop to make the data "crash consistent" for theSnapshot of the datastore to even make any sense. So, if you want to take Snapshots, itshould be something you coordinate with the ESX server and its guest OS images, and notscheduled by the N series itself.
If you are running NFS protocol to N series, you can turn off the "accesstime" updates. In normal file systems, when you read a file, it updates the"access time" in the file directory. This can be useful if you are looking forfiles that haven't been read in a while, such as software that migrates infrequentlyaccessed files to tape. Assuming you are not doing that on your N series, you might as well turnoff this feature, and reduce the unnecessary write activity to the IBM N series box.
ESX server can also support "thin provisioning" on the IBM N series. There isa checkbox for "space reserved". Checked means "thick provisioning" and uncheckedmeans "thin provisioning". If you decide to use "thin provisioning" with VMware,you should consider setting AutoSize to automatically increase your datastorewhen needed, and to auto-delete-snap your oldest snapshots first.
The key advantage of using NFS rather than FCP or iSCSI is that it eliminates theuse of the VMFS file system. IBM N series has the WAFL file system instead, andso you don't have to worry about VMFS partition alignment issue. Most VMDK aremisaligned, so the performance is sub-optimal. If you can align each VMDK to a32KB or 64KB boundary (depending on guest OS), then you can get better performance.WAFL does this for you automatically, but VMFS does not. For Windows guests, use "Windows PE" to configurecorrectly-aligned disks. For UNIX or Linux guests, use "fdisk" utility.
What Industry Analysts are saying about IBM
Vic Peltz gave a presentation highlighting the accolades from securities analysts, IT analysts, and newsagencies about IBM and IBM storage products. For example, analysts like that IBM offersmany of the exciting new technologies their clients are demanding, like "thin provisioning", RAID-6 double-drive protection,SATA and Solid State Disk (SSD) drive technology.Analysts also like that IBM is open to non-IBM heterogeneous environments. Whereas EMC Celerra gateways supportonly EMC disk, IBM N series gateways and IBM SAN Volume Controller support a mix of IBM and non-IBM equipment.
Analysts also like IBM's "datacenter-wide" approach to issues like security and "Green IT". Rather than focusingon these issues with individual point solutions, IBM attacks these challenges with a complete"end-to-end" solution approach. A typical 25,000 square foot data center consumes $2.6 million dollars USD in power andcooling today, and IBM has proven technologies to reduce this cost in half. IBM's DS8000 on average consume26.5 to 27.8 percent less electricity than a comparable EMC DMX-4 disk system. IBM's tape systemsconsume less energy than comparable Sun or HP models.
IBM iDataPlex product technical presentation
Vallard Benincosa, IBM Technical Sales Specialist, presented the recently-announced [IBM System x iDataPlex].This is designed for our clients that have thousands of x86 servers, that buy servers "racks at a time", tosupport Web 2.0 and digital archive workloads. The iDataPlex is designed for efficient power and cooling,rapid scalability, and usable server density.
iDataPlex is such a radical design departure, that it might be difficult to describe in words.Most racks take up two floor tiles, each tile is 2 foot by 2 foot square. In that space, a traditionalrack would have servers that were 19 inches wide slide in horizontally, with flashing lights and hot-swappabledisks in the front, and all the power supply, fans and networking connections in the back. Even with IBM BladeCenter,you have chassis in these racks, and then servers slide in vertically in the front, and all of the power supply, fanand networking connections in the back. To access these racks, you have to be able to open the door on boththe front and back. And the cooling has to go through at least 26.5 inches from the front of the equipment to the back.
iDataPlex turns the rack sideways. Instead of two feet wide, and four feet deep, it is four feet wide, and two feet deep.This gives you two 19 inch columns to slide equipment into, and the air only has to travel 15 inches from frontto back. Less distance makes cooling more efficient.
Next, iDataPlex makes only thing in the back the power cord, controlled by an intelligent power distribution unit (iPDU) so you can turnthe power off without having to physically pull the plug. Everything else is serviced from the front door.This means that the back door can now be an optional "Rear Door Heat Exchanger" [RDHX] that is filled with running water to makecooling the rack extremely efficient. Water from a cooler distirubtion unit (CDU) can power about threeto four RDHX doors.
Let's say you wanted to compare traditional racks with iDataPlex for 84 servers. You can put 42 "1U" serversin two racks each, each rack requires 10 kVA (kilo-volt-amps) so you give it two 8.6 kVA feeds each, that is fourfeeds, and at $1500-2000 dollars USD per month, will cost you $6000-8000. The iDataPlex you can fit 84 serversin one 20 kVA rack, with only three 8.6 kVA feeds, saving you $1500-2000 dollars USD per month.
Fans are also improved. Fan efficiency is based on their diameter, so small fans in 1U servers aren't as effective as iDataPlex's 2U fans, saving about 12-49W per server. Whereas typical 1U server racks spend 10-20percent of their energy on the fans, the iDataPlex spends only about 1 percent, saving 8 to 36 kWH per year per rack.
Each 2U chassis snaps into a single power supply and a bank of 2U fans. A "Y"power cord allows you to have one cord for two power supplies. A chassis can hold either two small server "flexnodes"or one big "flexnode". An iDataPlex rack can hold up to 84 small servers or 42 big servers. Since each "Y" cord can power up to four "flexnode" servers, you greatly reduce the number of PDU sockets taken,leaving some sockets available for traditional 1U switches.
The small "flexnode" server can have one 3.5 inch HDD, or two 2.5 inch HDD, either SAS or SATA, and the big "flexnode" can have twice these.If you need more storage, there is a 2U chassis that holds five 3.5 inch HDD or eight 2.5 inch HDD. These areall "simple-swappable" (servers must be powered down to pull out the drives). For hot-swappable drives, a 3Uchassis with twelve 3.5 inch SAS or SATA drives.
The small "flexnode" server has one [PCI Express] slot, the big servers have two. Thesecould be used for [Myrinet] clustering. With only 25W power,the PCI Express slots cannot support graphics cards.
The iDataPlex is managed using the "Extreme Cluster Administration Toolkit" [XCAT]. This is an open source project under Eclipse that IBM contributes to.
Finally was the concept of "pitch". This is the distance from the center of one "cold aisle" to the next "cold aisle".On typical data centers, a pitch is 9 to 11 tiles. With the iDataPlex it is only three tiles when using the RDHX doors, or six tiles without. Most data centers run out of power and cooling before they run out of floor space, so having more dense equipmentdoesn't help if it doesn't also use less electricity.Since the iDataPlex uses 40 percent less power and cooling, you can pack more racks persquare foot of an existing data center floor with the existing power and cooling available. That is what IBM calls "usable density"!
What Did You Say? Effective Questioning and Listening Techniques
Maria L. Anderson, IBM Human Resources Learning, gave this "professional development" talk. I deal with different clients every week, so I fully understand that there is a mix of art and science incrafting the right questions and listening to the responses.The focus was on howto ask better questions and improve the understanding and communication during consultative engagements. Thisinvolves the appropriate mix of closed and open-ended questions, exchanging or prefacing as needed. This wasa good overview of the ERIC technique (Explore, Refine, Influence, and Confirm).
Well, that wraps up my week here in Los Angeles.Special thanks to my two colleagues, Jack Arnold and Glenn Hechler, both from the Tucson Executive Briefing Center,who helped me prepare and review my presentations!
Continuing this week in Los Angeles, I went to some interesting sessions today at theSystems Technical Conference (STC08).
System Storage Productivity Center (SSPC) - Install and Configuration
Dominic Pruitt, an IBM IT specialist in our Advanced Technical Support team, presented SSPC and howto install and configure it. For those confused between the difference of TotalStorage ProductivityCenter and System Storage Productivity Center, the former is pure software that you install on aWindows or Linux server, and the latter is an IBM server, pre-installed with Windows 2003, TotalStorageProductivity Center software, TPCTOOL command line interface, DB2 Universal Database, the DS8000 Element Manager, SVC GUI and CIMOM, and [PuTTY] rLogin/SSH/Telnet terminal application software.
Of course, the problem with having a server pre-installed with a lot of software is that there is alwayssomeone that wants to customize it further. For those who just want to manage their DS8000 disk systems,for example, it is possible to uninstall the SVC GUI, CIMOM and PuTTY, and re-install them later when youchange your mind. As a general rule, it is not wise to mix CIMOMs on the same machine, as it might causeconflicts with TCP ports or Java level requirements, so if you want a different CIMOM than SVC, uninstallthe SVC CIMOM first. For those who have SVC, the SSPC replaces the SVC Master Console, so you can safelyturn off the SVC CIMOM on your existing SVC Master Consoles.
The base level is TotalStorage Productivity Center "Basic Edition", but you can upgrade the Productivity Centerfor Disk, Data and Fabric components with license keys. You can also run Productivity Center for Replication,but IBM recommends adding processor and memory to do this (IBM offers this as an orderable option).Whether you have the TotalStorage software or SSPC hardware, Productivity Center has a cool role-to-groups mapping feature.You can create user groups, either on the Windows server, the Active Directory, or other LDAP, and then map which roles should be assigned to users in each group.
Since Productivity Center manages a variety of different disk systems, it has made anattempt to standardize some terminology. The term "storage pool" refers to an extentpool on the DS8000, or a managed disk group on the SAN Volume Controller. Since the DS8000 can support both mainframe CKD volumes and LUNs for distributed systems, theterm "volume" refers to a CKD volume or LUN, and "disk" refers to the hard disk drive (HDD).
To help people learn Productivity Center, IBM offers single-day "remote workshops"that use Windows Remote Desktop to allow participants to install, customize and usethe software with no travel required.
IBM Integrated Approach to Archiving
Dan Marshall, IBM global program manager for storage and data services on our Global Technology Services team, presented IBM's corporate-wide integration to support archive across systems, software and services.One attendee asked me why I was there, given that "archive" is one of my areas of subject matter expertise that I present often at the Tucson Executive Briefing Center. I find it useful to watch others present the material, even material that I helped to develop, to see a different slant or spin on each talking point.
Archive is one area that brings all parts of IBM together: systems, software and services.Dan provided a look at archive from the services angle, providing an objective unbiasedview of the different software and systems available to solve specific challenges.
Encryption Key Manager (EKM) Design and Implementation
Jeff Ziehm, IBM tape technical sales specialist, presented IBM's EKM software, how it works in a tape environment, and how to deploy it in various environments. Since IBM is allabout being open and non-proprietary, the EKM software runs on Java on a variety ofIBM and non-IBM operating systems. IBM offers "keytool" command line interface (CLI) for the LTO4 and TS1120 tape systems, and "iKeyMan" graphical user interface (GUI) for theTS1120. Since it runs on Java, IBM Business Partners and technical support personneloften just [download and install EKM]onto their own laptops to learn how to use it.
Virtual Tape Update
We had three presenters at this one. First, Jeff Mulliken, formerly from Diligent and now a full IBM employee, presented the current ProtecTier softwarewith the HyperFactor technology, then Abbe Woodcock, IBM tape systems, compared Diligent with IBM's TS7520 and just-announced TS7530virtual tape libraries, and finally Randy Fleenor, IBM tape sales leader, presented IBM's strategy going forward in tape virtualization.
Let's start with Diligent. The ProtecTier software runs on any x86-64 server withat least four cores and the correct Emulex host bus adapter (HBA) cards. Using Red HatEnterprise Linux (RHEL) as a base, the ProtecTier software performs its deduplication entirely in-lineat an "ingest rate" of 400-450 MB/sec. This is all possible using 4GB memory-resident "dictionary table" that can map up to 1 PB of back end physical storage, which could represent as much as 25PB of "nominal" storage. Theserver is then point-to-point or SAN-attached to Fibre Channel disk systems.
As we learned yesterday from Toby Marek's session, there are four ways to performdeduplication:
full-file comparisons. Store only one copy of identical files.
fixed-chunk comparisons. Files are carved up into fixed-size chunks, and each chunkis compared or hashed to existing chunks to eliminate duplicates.
variable-chunk comparisons. Variable-length chunks are hashed or diffed to eliminate duplicate data.
content-aware comparisons. If you knew data was in Powerpoint format, for example,you could compare text, photos or charts against other existing Powerpoint files toeliminate duplicates.
IBM System Storage N series Advanced Single Instance Storage (A-SIS) uses fixed-chunkmethod, and Diligent uses variable-chunk comparisons. Diligent does this using "dataprofiling". For example, let's say most of my photographs are pictures of people, buildings, landscapes, flowers and IT equipment. When I back these up, the Diligentserver "profiles" each, and determines if any existing data have a similar profilethat might have at least 50 percent similar content. Diligent than reads in the data that is mostly likely similar, does a byte-for-byte ["diff" comparison], and creates variable-lengthchunks that are either identical or unique to sections of the existing data. Theunique data is compressed with LZH and written to disk, and the sequential series of pointer segments representing the ingested file is written in a separate section on disk.
That Diligent can represent profiles for 1PB of data in as little as 4GB memory-residentdictionary is incredible. By comparison, 10TB data would require 10 million entries on a content-aware solution, and 1.25 billion entries for one based on hash-codes.
Abbe Woodcock presented the TS7530 tape system that IBM announced on Tuesday. It has some advantages over the current Diligent offering:
Hardware-based compression (TS7520 and Diligent use software-based compression)
1200 MB/sec (faster ingest rate than Diligent)
1.7PB of SATA disk (more disk capacity than Diligent)
Support for i5/OS (Diligent's emulation of ATL P3000 with DLT7000 tapes not supported on IBM's POWER systems running i5/OS)
Ability to attach a real tape library
NDMP backup to tape
tape "shredding" (virtual equivalent of degaussing a physical tape to erase all previously stored data)
Randy Fleenor wrapped up the session telling us IBM's strategy going forward with all of thevirtual tape systems technologies. Until then, IBM is working on "recipes" or "bundles", puttingDiligent software with specific models of IBM System x servers and IBM System Storage DS4000 disk systemsto avoid the "do-it-yourself" problems of its current software-only packaging.
Understanding Web 2.0 and Digital Archive Workloads
I got to present this in the last time slot of the day, just before everyone headed off to the [Westin Bonaventure hotel] for our big fancy barbecue dinner. Like my previous sessionon IBM Strategy, this session was more oriented toward a sales audience, but both garnereda huge turn-out and were well-received by the technical attendees.
This session was requested because these new applications and workloads are what is driving IBM to acquire small start-ups like XIV, deploy Scale-Out File Services (SOFS), and develop the innovative iDataPlex server rack.
The session was fun because it was a mix of explanation of the characteristics ofWeb 2.0 services; my own experience as a blogger and user of Google Docs, FlickR, Second Life andTivo; and an exploration in how database and digital archives will impact thegrowth in computing and storage requirements.
I'll expand on some of these topics in later blog posts.