Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Tony Pearson is a Master Inventor and Senior Software Engineer for the IBM Storage product line at the
IBM Executive Briefing Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services. You can also follow him on Twitter @az990tony.
(Short URL for this blog: ibm.co/Pearson
Continuing my week in Washington DC for the annual [2010 System Storage Technical University], I presented a session on Storage for the Green Data Center, and attended a System x session on Greening the Data Center. Since they were related, I thought I would cover both in this post.
Storage for the Green Data Center
I presented this topic in four general categories:
Drivers and Metrics - I explained the three key drivers for consuming less energy, and the two key metrics: Power Usage Effectiveness (PUE) and Data Center Infrastructure Efficiency (DCiE).
Storage Technologies - I compared the four key storage media types: Solid State Drives (SSD), high-speed (15K RPM) FC and SAS hard disk, slower (7200 RPM) SATA disk, and tape. I had comparison slides that showed how IBM disk was more energy efficient than competition, for example DS8700 consumes less energy than EMC Symmetrix when compared with the exact same number and type of physical drives. Likewise, IBM LTO-5 and TS1130 tape drives consume less energy than comparable HP or Oracle/Sun tape drives.
Integrated Systems - IBM combines multiple storage tiers in a set of integrated systems managed by smart software. For example, the IBM DS8700 offers [Easy Tier] to offer smart data placement and movement across Solid-State drives and spinning disk. I also covered several blended disk-and-tape solutions, such as the Information Archive and SONAS.
Actions and Next Steps - I wrapped up the talk with actions that data center managers can take to help them be more energy efficient, from deploying the IBM Rear Door Heat Exchanger, or improving the management of their data.
Greening of the Data Center
Janet Beaver, IBM Senior Manager of Americas Group facilities for Infrastructure and Facilities, presented on IBM's success in becoming more energy efficient. The price of electricity has gone up 10 percent per year, and in some locations, 30 percent. For every 1 Watt used by IT equipment, there are an additional 27 Watts for power, cooling and other uses to keep the IT equipment comfortable. At IBM, data centers represent only 6 percent of total floor space, but 45 percent of all energy consumption. Janet covered two specific data centers, Boulder and Raleigh.
At Boulder, IBM keeps 48 hours reserve of gasoline (to generate electricity in case of outage from the power company) and 48 hours of chilled water. Many power outages are less than 10 minutes, which can easily be handled by the UPS systems. At least 25 percent of the Computer Room Air Conditioners (CRAC) are also on UPS as well, so that there is some cooling during those minutes, within the ASHRAE guidelines of 72-80 degrees Fahrenheit. Since gasoline gets stale, IBM runs the generators once a month, which serves as a monthly test of the system, and clears out the lines to make room for fresh fuel.
The IBM Boulder data center is the largest in the company: 300,000 square feet (the equivalent of five football fields)! Because of its location in Colorado, IBM enjoys "free cooling" using outside air temperature 63 percent of the year, resulting in a PUE of 1.3 rating. Electricity is only 4.5 US cents per kWh. The center also uses 1 Million KwH per year of wind energy.
The Raleigh data center is only 100,000 Square feet, with a PUE 1.4 rating. The Raleigh area enjoys 44 percent "free cooling" and electricity costs at 5.7 US cents per kWh. The Leadership in Energy and Environmental Design [LEED] has been updated to certify data centers. The IBM Boulder data center has achieved LEED Silver certification, and IBM Raleigh data center has LEED Gold certification.
Free cooling, electricity costs, and disaster susceptibility are just three of the 25 criteria IBM uses to locate its data centers. In addition to the 7 data centers it manages for its own operations, and 5 data centers for web hosting, IBM manages over 400 data centers of other clients.
It seems that Green IT initiatives are more important to the storage-oriented attendees than the x86-oriented folks. I suspect that is because many System x servers are deployed in small and medium businesses that do not have data centers, per se.
Michael Scott, one of my "Second Life" builder/scripters, for demonstrating client-focused dedication to IBM's corporate values.
Our site manager, Terri Mitchell, did a recap of all our recent awards and accomplishments.Of the nine Design Innovation awards won by IBM this year at the CeBIT conference, eight were for IBM System Storage products!
The IBM System Storage EXP3000: an entry-level data storage server that is optimized for cost-sensitive and space-limited environments and employs a user-centered design that enables ease of use and simple tool-less installation and removal of all components.
The IBM System Storage N7000 Series: a modular disk storage system that delivers high-end enterprise storage and data management value ideal for large-scale applications, while helping to anticipate growth, maintaindata availability and reduce costs.
The IBM System Storage N5000 Series: a modular disk storage system designed to address the entire spectrum of data availability challenges while offering value in price and scalability. Built-in enterprise serviceability and manageability features support efforts to increasereliability and simplify storage infrastructure and maintenance.
The IBM System Storage N3700: a filer that integrates storage and storage processing into a single unit, facilitating affordable network deployments.
The IBM System Storage DS4700: a NEBS-compliant disk storage server designed to address requirements for companies in the telecommunications industry, as well as other segments, such as oil and gas, meeting standardsfor electromagnetic compatibility, thermal robustness, earthquake and office vibration resistance, and provides protection for the product components from airborne contaminants.
The IBM System Storage EXP810: a data storage expansion unit capable of 4.8 Terabytes of physical storage, with a user-centered and tool-less design featuring redundant power, cooling, and disk modules for ease of use and simple serviceability.
The IBM System Storage TS3400: an affordable, space-friendly tape library for users in remote locations that supports enterprise-class technology and encryption capabilities.
A representative from Tucson's Brewster Center presented Terri an award, thanking IBM for its strong support for the community through various charity initiatives.
The final speaker was a new IBM client, Tony Casella, the IT Director of the town of Marana. Recently, the town of Marana selected IBM products made big news. Arizona is the fastest growing state in the USA, and the town of Marana, just north of Tucson, is one of the fastest growing communities in Arizona. The town is growing so large that it will soon spill over from Pima into Pinal county, and will be the first town in Arizona authorized to span county boundaries.
Well, it's Tuesday, and so it is "announcement day" again! Actually, for me it is Wednesday morning herein Mumbai, India, but since I was "press embargoed" until 4pm EDT in talking about these enhancements, I had to wait until Wednesday morning here to talk about them.
World's Fastest 1TB tape drive
IBM announced its new enterprise [TS1130 tape drive]and corresponding [TS3500 tape library support]. This one has a funny back-story. Last week while we were preparing the Press Release, we debated on whether we should compare the 1TB per cartridge capacity as double that of Sun's Enterprise T10000 (500GB), or LTO-4 (800GB). The problem changed when Sun announced on Monday they too had a 1TB tape drive, so now instead ofsaying that we had the "World's First 1TB tape drive", we quickly changed this to the "World's Fastest 1TB tape drive" instead. At 160MB/sec top speed, IBM's TS1130 is 33 percent faster than Sun's latest announcement. Sun was rather vague when they will actually ship their new units, so IBM may still end up being first to deliver as well.
While EMC and other disk-only vendors have stopped claiming that "tape is dead", these recent announcements from IBM and Sun indicate that indeed tape is alive and well. IBM is able to borrow technologies from disk, such as the Giant Magneto Resistive (GMR) head over to its tape offerings, which means much of the R&D for disk applies to tape, keeping both forms ofstorage well invested. Tape continues to be the "greenest" storage option, more energy efficient than disk, optical, film, microfiche and even paper.
On the LTO front, IBM enhanced the reporting capabilities of its[TS3310] midrange tape library. This includes identifying the resource utilization of the drives, reporting on media integrity, and improved diagnostics to support library-managed encryption.
IBM System Storage DR550
As a blended disk-and-tape solution, the [IBM System Storage DR550] easily replaces the EMC Centera to meet compliance storagerequirements. IBM announced that we have greatly expanded its scalability, being able to support both 1TBdisk drives, as well as being able to attach to either IBM or Sun's 1TB tape drives.
Massive Array of Idle Disks (MAID)
IBM now offers a "Sleep Mode" in the firmware of the [IBM System Storage DCS9550], which is often called "Massive Array of Idle Disks" (MAID) or spin-down capability. This can reduce the amount of power consumed during idle times.
That's a lot of exciting stuff. I'm off to breakfast now.
The "Storage Symposium Mexico - 2008" conference was a great success this week!
Day 1 - The plan was for me to arrive for the Wednesday night reception. Eachattendee was given a copy of my latest book[Inside System Storage: Volume I] and I was planning to sign them. I thought perhaps we should have a "book signing" tablelike all of the other published authors have.
Things didn't go according to plan. Thunderstorms at the Mexico City airport forced our pilot to find an alternate airport. Nearby Acapulco airport was the logical choice, but was full from all the otherflights, so the plane ended up in a tiny town called McAllen, Texas. I did not arrive until the morning of Day 2,so ended up signing the books throughout Thursday and Friday, during breaks and meals, wherever they couldfind me!
Special thanks to fellow IBMer Ian Henderson who picked me up from the airport at such an awkward hour anddrive me all the way to Cuernavaca!
All of us, IBMers, Business Partners and clients alike, all donned black tee-shirtswith a white eightbar logo for a group photo with one of those "wide lens" cameras. While we werebeing assembled onto the bleachers, I took this quick snapshot of myself and some of the guys behind me.
I was original scheduled to be first to speak, but with my flight delays, was moved to a time slot after lunch.After a big Mexican lunch, the conference coordinators were afraid the attendees might fall asleep,a Mexican tradition called [siesta], so I wasinstructed to WAKE THEM UP! Fortunately, my topic was Information Lifecycle Management, a topicI am very passionate about, since my days working on DFSMS on the mainframe. With 30percent reduction in hardware capital expenditures, 30 percent reduction in operational costs, and typical payback periods between 15 to 24 months, the presentation got everyone's attention.
Of course, a lot happens outside of the formal meetings. We had a Japanese theme dinner, where we woreJapanese Hachimaki [headbands]with the eightbar logo. For those not familiar with Japanese culture, hachimaki are worn today not so much for the practical purpose to catch the perspiration but rather for mental stimulation to express one's determination. Some students wear hachimaki when they study to put themselves in the right spirit and frame of mind.
Shown here are presenters Mike Griese (Infrastructure Management with IBM TotalStorage Productivity Center),Dave Larimer (Backup and Storage Management with IBM Tivoli Storage Manager), myself, and John Hamano(Unified Storage with IBM System Storage N series).
Day 3 - Wrapping up the week, I presented two more times.
First, I covered IBM Disk Virtualization with IBM SAN Volume Controller. One interesting question was if the SAN Volume Controller could be made to looklike a Virtual Tape Library. I explained that this was never part of the original design, but that if you wantto combine SVC with a VTL into a combined disk-and-tape blended solution, consider using theIBM product called Scale-Out File Services[SoFS] which I covered in my post[Moredetails about IBM clustered scalable NAS].
During one of the breaks, I took a picture of the behind-the-scenes staff that put this together. They had created these huge blocks representing puzzle pieces, emphasizing how IBM is one of the few ITvendors that can bring all the pieces together for a complete solution.
Shown hereare Mike Griese (presenter), Cyntia Martinez, Claudia Aviles, Cesar Campos (IBM Business Unit Executive forSystem Storage in Mexico), and Claudia Lopez. Each day the staff wore matching shirts so that it was easyto find them.
Later, I covered Archive and Compliance Solutions to highlight our complete end-to-end set of solutions.When asked to compare and contrast the architectures of the IBM System Storage DR550 with EMC Centera, I explainedthat the DR550 optimizes the use of online disk access for the most recent data. For example, if you aregoing to keep data for 10 years, maybe you keep the most recent 12 months on disk, and the rest is moved,using policy-based automation, to a tape library for the remaining nine years. This means that the disk insidethe DR550 is always being used to read and write the most recent data, the data you are most likely to retrievefrom an archive system. Data older than a year is still accessible, but might take a minute or two for the tapelibrary robot to fetch.The EMC Centera, on the other hand, is a disk-only solution. It offers no option to move older data to tape,nor the option to spin-down the drives to conserve power. It fills up after the same 12 months or so, and then you get towatch it the remaining nine years, consuming electricity and heating your data center.
I don't know about you, butI have never seen anyone purposely put in "space heaters" into their data center, but certainly a full EMC Centeradoes little else. Both devices use SATA drives and support disk mirroring between locations, but IBM DR550 offers dual-parity RAID-6, and supports encryption of the data on both the disk and the tape in the DR550. EMC Centerastill uses only RAID-5, and has not yet, as far as I know, offered any level of encryption. IBM System StorageDR550 was clocked at about three times faster than Centera at ingesting new archive objects over a 1GbE Ethernet connection.
This last photo is me and fellow IBMer Adriana Mondragón. She was one of my students in the [System Storage Portfolio Top Gun class],last February in Guadalajara, Mexico.She graduated in the top 10 percent of her group, earning her the prestigious titleof "Top Gun" storage sales specialist.
The conference wrapped up with a Mexican lunch with a traditional Mariachi band. I took pictures, but figured you allalready know what [Mariachi players] look like, and I didn't wantto detract from the otherwise serious tone of this blog post! This was the first System Storage Symposium in Mexico, butbased on its success, we might continue these annually.
This month (September, 2006) marks our 50th anniversary of the disk system. The first disk system was the 350 Disk Storage Unit, designed to attach to the IBM 305 RAMAC mainframe computer, both introduced to the world in September, 1956.
The weather has warmed up here in Tucson so I started my Spring Cleaning early this year and unearthed from my garage a [Bankers Box] full of floppy diskettes.
IBM invented the floppy disk back in 1971, and continued to make improvements and enhancements through the 1980s and 1990s. It will be one of the many inventions celebrated as part of IBM's Centennial (100-year) anniversary. Here is an example [T-shirt]
IBM needed a way to send out small updates and patches for microcode of devices out in client locations. IBM had drives that could write information, and sent out "read-only" drives to the customer locations to receive these updates. These were flexible plastic circles with a magnetic coating, and placed inside a square paper sleeve. Imagine a floppy disk the size of a piece of standard paper. The 8-inch floppy fit conveniently in a manila envelope, sendable by standard mail, and could hold nearly 80KB of data.
I've been using floppies for the past thirty years. Here's some of my fondest memories:
While still in high school, my friend Franz Kurath and I formed "Pearson Kurath Systems", a software development firm. We wrote computer programs to run on UNIX and Personal Computers for small businesses here in Tucson. Whenever we developed a clever piece of code, a subroutine or procedure, we would save it on a floppy disk and re-use it for our next project. We wrote in the BASIC language, and our databases were simple Comma-Separated-Variable (CSV) flat files.
The 5.25-inch floppies we used could hold 360KB, and were flexible like the 8-inch models. Later versions of these 5.25-inch floppies would be able to hold as much as 1.2MB of data. We would convert single-sided floppies into double-sided ones by cutting out a notch in the outer sleeve. Covering up the notches would mark them as read-only.
The 3.5-inch floppies were introduced with a hard plastic shell, with the selling point that you can slap on a mailing label and postage and send it "as is" without the need for a separate envelope. These new 3.5-inch floppies would carry "HD" for high density 720KB, and double-sided versions could hold 1.44MB of data. The term "diskette" was used to associate these new floppies with [hard-shelled tape cassettes]. Sliding a plastic tab would allow floppies to be marked "read-only". IBM has the patent on this clever invention.
Continuing our computer programming business in college, Franz and I took out a bank loan to buy our first Personal Computer, for over $5000 dollars USD. Until then, we had to use equipment belonging to each client. The banks we went to didn't understand why we needed a computer, and suggested we just track our expenses on traditional green-and-white ledger paper. Back then, peronsal computers were for balancing your checkbook, playing games and organizing your collection of cooking recipies. But for us, it was a production machine. A computer with both 5.25-inch and 3.5-inch drives could copy files from one format to another as needed. The boost in productivity paid for itself within months.
Apple launched its Macintosh computer in 1984, with a built-in 3.5-inch disk drive as standard equipment. Here is a YouTube video of an [astronaut ejecting a floppy disk] from an Apple computer in space.
In my senior year at the University of Arizona, my roommate Dave had borrowed my backpack to hold his lunch for a bike ride. He thought he had taken everything out, but forgot to remove my 3.5-inch floppy diskette containing files for my senior project. By the time he got back, the diskette was covered in banana pulp. I was able to rescue my data by cracking open the plastic outer shell, cleaning the flexible magnetic media in soapy water, placing it back into the plastic shell of a second diskette, and then copied the data off to a third diskette.
After graduating from college, Franz and I went our separate ways. I went to work for IBM, and Franz went to work for [Chiat/Day], the advertising agency famous for the 1984 Macintosh commercial. We still keep in touch through Facebook.
At IBM, I was given a 3270 terminal to do my job, and would not be assigned a personal computer until years later. Once I had a personal computer at home and at work, the floppy diskette became my "briefcase". I could download a file or document at work, take it home, work on it til the wee hours of the morning, and then come back the next morning with the updated effort.
To help prepare me for client visits and public speaking at conferences, IBM loaned me out to local schools to teach. This included teaching Computer Science 101 at Pima Community College. When asked by a student whether to use "disc" or "disk", I wrote a big letter "C" on the left side of the chalkboard, and a big letter "K" on the right side. If it is round, I told the students while pointing at the letter "C", like a CD-ROM or DVD, use "disc". If it has corners, pointing to corners of the letter "K", like a floppy diskette or hard disk drive, use "disk".
On one of my business trips to visit a client, we discovered the client had experienced a problem that we had just recently fixed. Normally, this would have meant cutting a Program Trouble Fix (PTF) to a 3480 tape cartridge at an IBM facility, and send it to the client by mail. Unwilling to wait, I offered to download the PTF onto a floppy diskette on my laptop, upload it from a PC connected to their systems, and apply it there. This involved a bit of REXX programming to deal with the differences between ASCII and EBCDIC character sets, but it worked, and a few hours later they were able to confirm the fix worked.
In 1998, Apple would signal the begining of the end of the floppy disk era, announcing their latest "iMac" would not come with an internal built-in floppy drive. David Adams has a great article on this titled [The iMac and the Floppy Drive: A Conspiracy Theory]. You can get external floppy drives that connect via USB, so not having an internal drive is no longer a big deal.
While teaching a Top Gun class to a mix of software and hardware sales reps, one of the students asked what a "U" was. He had noticed "2U" and "3U" next to various products and wondered what that was referring to. The "U" represents the [standard unit of measure for height of IT equipment in standard racks]. To help them visualize, I explained that a 5.25-inch floppy disk was "3U" in size, and a 3.5-inch floppy diskette was "2U". Thus, a "U" is 1.75 inches, the thinnest dimension on a two-by-four piece of lumber. Servers that were only 1U tall would be referred to as "pizza boxes" for having similar dimensions.
Every year, right around November or so, my friends and family bring me their old computers for me to wipe clean. Either I would re-load them with the latest Ubuntu Linux so that their kids could use it for homework, or I would donate it to charity. Last November, I got a computer that could not boot from a CD-ROM, forcing me to build a bootable floppy. This gave me a chance to check out the various 1-disk and 2-disk versions of Linux and other rescue disks. I also have a 3-disk set of floppies for booting OS/2 in command line mode.
So while this unexpected box of nostalgia derailed my efforts to clean out my garage this weekend, it did inspire me to try to get some of the old files off them and onto my PC hard drive. I have already retrieved some low-res photographs, some emails I sent out, and trip reports I wrote. While floppy diskettes were notorious for being unreliable, and this box of floppies has been in the heat and cold for many Arizonan summers and winters, I am amazed that I was able to read the data off most of them so far, all the way back to data written in 1989. While the data is readable, in most cases I can't render it into useful information. This brings up a few valuable lessons:
Backups are not Archives
Some of the files are in proprietary formats, such as my backups for TurboTax software. I would need a PC running a correct level of Windows operating system, and that particular software, just to restore the data. TurboTax shipped new software every year, and I don't know how forward or backward-compatible each new release was.
Another set of floppies are labeled as being in "FDBACK" format. I have no idea what these are. Each floppy has just two files, "backup.001" and "control.001", for example.
Backups are intended solely to protect against unexpected loss from broken hardware or corrupted data. If you plan to keep data as archives for long-term retention, use archive formats that will last a long time, so that you can make sense of them later.
Operating System Compatibility
Windows 7 and all of my favorite flavors of Linux are able to recognize the standard "FAT" file system that nearly all of my floppies are written in. Sadly, I have some files that were compressed under OS/2 operating system using software called "Stacker". I may have to stand up an OS/2 machine just to check out what is actually on those floppies.
You can't judge a book by its cover
Floppies were a convenient form of data interchange. Sometimes, I reused commercially-labeled floppies to hold personal files. So, just because a floppy says "America On-Line (AOL) version 2.5 Installation", I can't just toss it away. It might actually contain something else entirely. This means I need to mount each floppy to check on its actual contents.
So what will I do with the floppies I can't read, can't write, and can't format? I think I will convert them into a [retro set of coasters], to protect my new living room furniture from hot and cold beverages.
A lot of people ask me about IBM branding, as we have recently changed brands. In the past we had two separate brands, one for servers (eServer) and one for storage (TotalStorage). These would be fine if we wanted to promote their independence, but customers today want synergy between servers and storage, they want systems that work well together.
Last year, in response to market feedback, we crated a new brand, "IBM Systems" and put all the server and storage product lines under one roof. Over time, we will transition from TotalStorage to System Storage naming. This will occur with new products, and major versions of existing products.
Two other phrases you will hear in the names of our offerings are "Virtualization Engine" and "Express". These are portfolio identifiers. The Virtualization Engine identifier was created to emphasize our leadership in system virtualization, and we have products that span product lines with this identifier.
The Express identifier was created to emphasize our focus on Small and Medium sized business (SMB). It spans not just servers and storage, but across other offerings from other IBM divisions.
Of course, just renaming products and services isn't enough. Systems don't work together just because they have similar names, are covered in similar "Apple white" plastic, or have similar black bezels. Obviously, thoughtful and collaborative design are needed, with the appropriate amounts of engineering and testing. IBM is aligning its server and storage development so that the IBM Systems brand keeps its promise.
With all the announcements we had in June, it is easy for some of the more subtle enhancements to get overlooked. While I was at Orlando for the IBM Edge conference, I was able to blog about some of the key featured announcements. Then, later, when I got back from Orlando to Tucson, I was able to then blog about [More IBM Storage Announcements]. For IBM's Scale-Out Network Attach Storage (SONAS), I had simply:
"SONAS v1.3.2 adds support for management by the newly announced IBM Tivoli Storage Productivity Center v5.1 release. Also, IBM now officially supports Gateway configurations that have the storage nodes connected to XIV or Storwize V7000 disk systems. These gateway configurations offer new flexible choices and options for our ever-expanding set of clients."
In my defense, IBM numbers its software releasees with version.release.modification, so 1.3.2 is Version 1, Release 3, Modification 2. Generally, modification announcements don't get much attention. The big announcement for v1.3.0 of SONAS happened last October, see my blog post [October 2011 Announcements - Part I] or
the nice summary post [IBM Scale-out Network Attached Storage 1.3.0] from fellow blogger Roger Luethy.
Here is a diagram showing the three configurations of SONAS.
I have covered the SONAS Appliance model in depth in previous blogs, with options for fast and slow disk speeds, choice of RAID protection levels, a collection of enterprise-class software features provided at no additional charge, and interfaces to support a variety of third party backup and anti-virus checking software.
The basics haven't changed. The SONAS appliance consists of 2 to 32 interface nodes, 2 to 60 storage nodes, and up to 7,200 disk drives. The maximum configuration takes up 17 frames and holds 21.6PB of raw disk capacity, which is about 17PB usable space when RAID6 is configured. An interface nodes has one or two hex-core processors with up to 144GB of RAM to offer up to 3.5GB/sec performance each. This makes IBM SONAS the fastest performing and most scalable disk system in IBM's System Storage product line.
I thought I would go a bit deeper on the gateway models. These models support up to ten storage nodes, organized in pairs. The key difference is that instead of internal disk controllers, the storage nodes connect to external disk systems. There is enough space in the base SONAS rack to hold up to six interface nodes, or you can add a second rack if you need more interface nodes for increased performance.
SONAS with XIV gateway
XIV offers a clever approach to storage that allows for incredibly fast access to data on relatively slow 7200 RPM drives. By scattering data across all drives and taking advantage of parallel processing, rebuild times for a failed 3TB drive are less than 75 minutes. Compare that to typical rebuild times for 3TB drives that could take as much as 9-10 hours under active I/O loads!
In the configuration, each pair of storage nodes can connect to external SAN Fabric switches that then connect to one or two XIV storage systems. How simple is that? These can be the original XIV systems that support 1TB and 2TB drives, or the new XIV Gen3 systems that support 400GB Solid-state drives (SSD) and 3TB spinning disk drives. In both cases, you can acquire additional storage capacity as little as 12 drives at a time (one XIV module holds 12 drives).
The maximum configuration of ten XIV boxes could hold 1,800 drives. At 3TB drive per drive, that would be 2.4PB usable capacity.
The SONAS with XIV gateway does not require the XIV devices to be dedicated for SONAS purposes. Rather, you can assign some XIV storage space for the SONAS, and the rest is available for other servers. In this manner, SONAS just looks like another set of Linux-based servers to the XIV storage system. This in effect gives you "Unified Storage", with a full complement of NAS protocols from the SONAS side (NFS, CIFS, FTP, HTTPS, SCP) as well as block-based protocols directly from the XIV (FCP, iSCSI).
SONAS with Storwize V7000 gateway
The other gateway offering is the SONAS with Storwize V7000. Like the SONAS with XIV gateway model, you connect a pair of SONAS storage nodes to 1 or 2 Storwize V7000 disk systems. However, you do not need a SAN Fabric switch in between. You can instead connect the SONAS storage nodes directly to the Storwize V7000 control enclosures.
To acquire additional storage capacity, you can purchase a single drive at a time. That's right. Not 12 drives, or 60 drives, at a time, but one at a time. The Storwize V7000 supports a wide range of SSD, SAS and NL-SAS drives at different sizes, speeds and capacities. The drives can be configured into various RAID protection levels: RAID 0, 1, 3, 5, 6 and 10.
Each Storwize V7000 control enclosure can have up to nine expansion drawers. If you choose the 2.5-inch 24-bay models, you can have up to 480 drives per storage node pair, for a total of 2,400 drives. If you choose the 3.5-inch 12-bay models, you can have up to 240 drives per node pair, 1,200 drives total. At 3TB per drive, this could be 3.6PB of raw capacity. The usable PB would depend on which RAID level you selected. Of course, you don't have to limit yourself all to one size or the other. Feel free to mix 2.5-inch and 3.5-inch drawers to provide different storage pool capabilities.
All three SONAS configurations support Active Cloud Engine. This is a collection of features that differentiate SONAS from the other scale-out NAS wannabees in the marketplace:
Policy-driven Data Placement -- Different files can be directed to different storage pools. You no longer have to associate certain file systems to certain storage technologies.
High-speed Scan Engine -- SONAS can scan 10 million files per minute, per node. These scans can be used to drive data migration, backups, expirations, or replications, for example. It is over 100 times faster than traditional walk-the-directory-tree approaches employed by other NAS solutions.
Policy-driven Migration -- You can migrate files from one storage pool to another, based on age, days since last reference, size, and other criteria. The files can be moved from disk to disk, or move out of SONAS and stored on external media, such as tape or a virtual tape library. A lot of data stored on NAS systems is dormant, with little or no likelihood of being looked at again. Why waste money keeping that kind of data on expensive disk? With SONAS, you can move those files to tape can save lots of money. The files are stubbed in the SONAS file system, so that an access request to a file will automatically trigger a recall to fetch the data from tape back to the SONAS system.
Policy-driven Expiration -- SONAS can help you keep your system clean, by helping you decide what files should be deleted. This is especially useful for things like logs and traces that tend to just hang around until some deletes them manually.
WAN Caching -- This allows one SONAS to act as a "Cloud Storage Gateway" for another SONAS at a remote location connected by Wide Area Network (WAN). Let's say your main data center has a large SONAS repository of files, and a small branch office has a smaller SONAS. This allows all locations to have a "Global" view of the all the interconnected SONAS systems, with a high-speed user experience for local LAN-based access to the most recent and frequently used files.
If you want to learn more, see the [IBM SONAS landing page]. Next week, I will be across the Pacific Ocean in [Taipei], to teach IBM Top Gun class to sales reps and IBM Business Partners. "Selling SONAS" will be one of the topics I will be covering!
It has always been the case in fast pace technology areas that you can't tell the players without a program card, andthis is especially true for storage.
When analyzing each acquistion move, you need to think of what is driving it. What are the motives?Having been in the storage business 20 years now, and seen my share of acquisitions, both from within IBM,as well as competition, I have come up with the following list of motives.
Although slavery was abolished in the US back in the 1800's, and centuries earlier everywhere else, many acquisitionsseem to be focused on acquiring the people themselves, rather than the products or client list. I have seen statistics such as "We retained 98% of the people!" In reality, these retentions usually involve costly incentives,sign-in bonuses, stock options, and the like. Desptie this, people leave after a few years, often because ofpersonality or "corporate culture" clash. For example, many former STK employees seem to be leaving after their company was acquired by Sun Microsystems.
If you can't beat them, join them. Acquisitions can often be used by one company to raise its ranking in marketshare, eliminating smaller competitors. And now that you have acquired their client list, perhaps you can sellthem more of your original set of products!
Symantec had acquired Veritas, which in turn had acquired a variety of other smaller players, and the end result is that they are now #1 backup software provider, even though none of theirproducts holds a candle to IBM's Tivoli Storage Manager. Meanwhile, EMC acquired Avamar to try to get more into the backup/recovery game, but most analysts still find EMC down in the #4 or #5 place in this category.
Next month,Brocade's acquisition of McData should take effect, furthering its marketshare in SAN switch equipment.
Prior to my current role as "brand market strategist" for System Storage, I was a "portfolio manager" where wetried to make sure that our storage product line investments were balanced. This was a tough job, as the investmentshad to balance the right development investments into different technologies, including patent portfolios.Despite IBM's huge research budget, I am not surprised that some clever inventions of new technologies comefrom smaller companies, that then get acquired once their results appear viable.
The last motive is value shift. This is where companies try to re-invent themselves, or find that they are stuck in acommodity market rut, and wish to expand into more profitable areas.
LSI Logic acquisition of StoreAge is a good exampleof this. Most of the major storage vendors have already shifted to software and services to provide customer value,as predicted in 1990's by Clayton Christensen in his book "The Innovator's Dilemma". The rest are still strugglingto develop the right strategy, but leaning in this general direction.
Jon Toigo over at DrunkenData writes in his post[A Wink and a Nod] about thebenefits of the new IBM System z10 Enterprise Class mainframe. Here's an excerpt about storage:
"The other key point worth making about this scenario is that storage behind a z10 must conform to IBM DASD rules. That means no more BS standards wars between knuckle-draggers in the storage world who continue to mitigate the heterogeneous interoperability and manageability of distributed systems storage using proprietary lock in technologies designed as much to lock in the consumer and lock out the competition as to deliver any real value. That has got to be worth something."
For z/OS and TPF operating systems, disk must support CCW commands over ESCON or FICON connections, or NFS commandsover the Local Area Network. However, most of the workloads that are being ported over from x86 platforms willprobably be running Linux on System z images, and as such Linux supports both CCW and SCSI protocols, the latterover native FCP connections through a Storage Area Network (SAN) or via iSCSI over the Local Area Network. Many SAN directors support both FCP and FICON, and the z10 also supports both 1Gbps and 10Gbps Ethernet, so you may not have to invest in any new networking gear.
The best part is that you may not have to migrate your data. The IBM System Storage SAN Volume Controller is supported for Linux on System z, and with "image mode" you can leave the data in its original format on its original disk array. Many file systems are now supported by Linux, including Windows NTFS with the latest NTFS-3G driver.
If your data is already on NAS storage, such as the IBM System Storage N series disk systems, then the IBM z10can access it directly, from z/OS, z/VM or Linux.
Have lots of LTO tape data? Linux on System z supports LTO as well.
Jon continues his rant with a question about porting Microsoft Windows applications. Here's another excerpt:
"For one, what do we do with all the Microsoft servers. There is no Redmond-sanctioned approach to my knowledge for virtualizing Microsoft SQL Server or Exchange Server in a mainframe partition."
Yes, it is possible to run Windows on a mainframe through emulation, but I feel that's the wrong approach. Instead, the focus should be on running "functionally equivalent" programs on the native mainframe operating systems, and again Linuxis often the best choice for this. Switching from Windows to Linux may not be "Redmond-sanctioned", but it getsthe job done.
Instead of SQL Server, consider something functionally equivalent like IBM's DB2 Universal Database, or perhaps an open source database like MySQL, PostgreSQL or Apache Derby. Well-written applications use standard SQL calls, so ifthe application does not try to use unique, proprietary features of MS SQL Server, you are in good shape.
In my discussion last November on [Microsoft Exchange email server], I mentioned that Bynari makes a functionally equivalent email server on Linux that works with your existing Microsoft Outlook clients. Your end-users wouldn't know you migrated to a mainframe! (well, they might notice their email runs faster)
So if your data center has three or more racks of Sun, Dell or HP "pizza box" or "blade" x86 servers, chances are you can migrate the processing over to a shiny new IBM z10 EC mainframe, save some money in the process, without too much impact to your existing Ethernet, SAN or storage system infrastructure. IBM can even help you dispose of the oldx86 machines so that their toxic chemicals don't end up in any landfill.
When new technologies are introduced to the marketplace, it is normal for customers to be skeptical.
My sister is a mechanical engineer, so when she needs to configure a part or component, she candesign it on the computer, and then use a "Rapid Prototyping Machine"that acts like a 3D printer, to generate a plastic part that matches the specifications. Some machinesdo this by taking a hunk of plastic and cutting it down to the appropriate shape, and others use glue andpowder to assemble the piece.
But not everything is that simple. Harry Beckwith deals with the issue of selling services and software featuresin his book "Selling the Invisible". How do you sell a service before it is performed? How do you sell a softwarefeature based on new technology that the customer is not familiar with?
Our good friends over at NetApp, our technology partners for the IBM System Storage N series, developed a"storage savings estimator" tool that can provide good insight into the benefits of Advanced Single InstanceStorage (A-SIS) deduplication feature.
I decided to run the tool to analyze my own IBM Thinkpad C: drive (Windows operating system and programs) and D: drive ("My Documents" folder containing all my data files) to see how much storage savings thetool would estimate. Here are my results:
WINXP-C-07G (C: drive)Total Number of Directories: 1272Total Number of Files: 56265Total Number of Symbolic Links: 0Total Number of Hard Links: 41996Total Number of 4k Blocks: 2395884Total Number of 512b Blocks: 18944730Total Number of Blocks: 2395884Total Number of Hole Blocks: 290258Total Number of Unique Blocks: 1611792Percentage of Space Savings: 20.61Scan Start Time: Wed Sep 5 14:37:06 2007Scan End Time: Wed Sep 5 14:53:51 2007
WINXP-D-07H (D: drive)Total Number of Directories: 507Total Number of Files: 7242Total Number of Symbolic Links: 0Total Number of Hard Links: 11744Total Number of 4k Blocks: 3954712Total Number of 512b Blocks: 31610595Total Number of Blocks: 3954712Total Number of Hole Blocks: 3204Total Number of Unique Blocks: 3524605Percentage of Space Savings: 10.79Scan Start Time: Wed Sep 5 14:21:16 2007Scan End Time: Wed Sep 5 14:34:30 2007
I am impressed with the results, and have a better understanding of the way A-SIS works. A-SIS looks at every4kB block of data, and creates a "fingerprint", a type of hash code of the contents. If two blocks have different "fingerprints", then the contents are known to be different. If two blocks have the same fingerprint, it is mathematically possible for them to be unique in content, so A-SIS schedules a byte-for-byte comparison to be sure they are indeed the same. This might happen hours after the block is initially written to disk, but is a much safer implementation, and does not slow down the applications writing data.
(In an effort to provide support "real time" as data was being written, earlier versions of deduplication
had to either assume that a hash collision was a match, or take time to perform the byte-for-byte comparisonrequired during the write process. Doing this byte-for-byte comparison when the device is the busiest doingwrite activities causes excessive undesirable load on the CPU.)
The estimator tool runs on any x86-based Laptop, personal computer or server, and can scan direct-attached, SAN-attached, or NAS-attached file systems. If you are a customer shopping around for deduplication, ask your IBM pre-sales technical support, storage sales rep, or IBM Business Partner to analyze your data. Tools like this can help make a simple cost-benefit analysis: the cost of licensing the A-SIS software feature versus the amount of storage savings.
In his blog Rough Type, Nick Carr asks Where is my CloudBook?and points to John Markoff's 2-part series in the New York Times on computing in the clouds.(Read it here: Part 1, Part 2)
At first, I thought he meant computing while in an airplane, but instead, he is talking about computing on a laptop or other hand-held device that does not have an internal disk drive, no installedoperating system, no internal data storage. Instead, the idea is that you boot from a CD, accessyour data, and even some of your programs, over the internet. John used an Ubuntu Linux LiveCD in his example.
This week, I am in Sao Paulo, Brazil, and was "in the clouds" for over 10 hours flying from Dallas to here.The one time I am guaranteed "off-line" from the internet is on the plane, and I spend enough time on planesthat I am able to get work done despite being "disconnected".
The same reasons people want to get out of having a disk drive on their laptop, are the reasons data centersare getting out of internal disk on their servers.
disks crash, and typically are not protected in any RAID configuration on most laptops
operating systems get infected with viruses and malware
storage on one server is generally inaccessible to every other server
Booting from CD is especially clever. No more worrying about fixing your Windows registry, viruses,corrupted operating system files, or the cruft that accumulates on your C: drive that slowsyou down. The CD is the sameevery time, so it is like running your system with a freshly installed operating system every day.
The need for central repositories of data harkens back to the years of the IBM mainframe. Of course, whatmade sense back then continues to make sense now. The old 3270 terminals stored no data, and instead merelyprovided keyboard input and display text screen output to the vast amount of data stored on the central system.Today, the inputs are different, using your finger or mouse instead to point to what you want, sliding itacross to make things happen, and the output may now include photos, audio and video, but the concept isstill the same.
I carry my Ubuntu Linux LiveCD with me on every business trip. Combined with externally rewriteable media,such as a USB key, you can get work done even when you are in an airplane, and upload it whenyou are back on the net.
Two European scientists, Albert Fert (France) and Peter Grunberg (Germany) have won the 2007 Nobel Prize for physics for their research into Giant Magnetoresistance, or GMR. GMR read/write heads are used in IBM disk systems.
New high-density dual-coated particulate magnetic tape: Developed by Fuji Photo Film Co., Ltd., in Japan in collaboration with IBM Almaden researchers, this next-generation version of its NANOCUBIC™ tape uses a new barium-ferrite magnetic media that enables high-density data recording without using expensive metal sputtering or evaporation coating methods.
More sensitive read-write head: For the first time, magnetic tape technology employs the sensitive giant-magnetoresistive (GMR) head materials and structures used to sense very small magnetic fields in hard disk drives.
GMR servo reader: New GMR servo-reading elements, software and fast-and-precise positioning devices provides an active feedback system with unprecedented 0.35-micron accuracy in monitoring and positioning the read-write head over the 1.5-micron-wide residual data track.
Improved tape-handling features: Flangeless, grooved rollers permit smoother high-speed passage of the tape, which also enhances the ability of the head to write and read high-density data.
Innovative signal processing algorithms for the read data channel: An advanced read channel used new "noise-predictive, maximum-likelihood" (NPML) software developed at IBM's Zurich Research Laboratory to process the captured data faster and more accurately than would have been possible with existing methods.
IBM often leverages the research done in one part of its business over to other parts of its business. In this manner, advances in disk translate into advances in tape, keeping tape a viable medium for at least the next 8-10 years.
Well, it's Tuesday again, and we had several announcements this month, so here is a quick recap.We had some things announce May 13, and then some more announcements today, but since I was busywith conferences, will combine them into one post for the entire month of May 2008.
This time, I thought I would go "audio" with a recording from Charlie Andrews, IBM director ofproduct marketing for IBM System Storage:
Well, its Tuesday, and that means more IBM announcements!!!
Let's do a quick recap of what was announced for storage:
We now support 1000GB SATA-II drives in the DS4000 series. This is available for the DS4200 model 7V, DS4700, DS4800 as well as the expansion drawers EXP420 and EX810. When I asked our marketing team why we weren't going to say "1TB" like everyone else, they thought 1000GB sounds bigger. I guess I should not have asked that on April Fool's day. For more details, see the IBM press releases for the [DS4200/EXP420and DS4700/DS4800/EXP810].
IBM announced new machine code Release 1.4a for the The IBM Virtualization Engine™ TS7700 virtual tape library for our System z mainframe customers.Various features come with this new level of machine code. See the IBM [Press Release] for more details.
Load balancing across the grid
Host control over the copy of logical volumes on a cluster by cluster basis
Option to gracefully remove an individual cluster from an existing grid
Initial-state reset for TS7700 database for cluster cleanup
Option to upgrade single-cache to dual-cache configuration
Also announced were updates to the 7214 model 1U2. Technically this is not in the IBM System Storage product line,but instead is designed specifically for our System p server line. This is a "media drawer" that allows you to havetape on one side, and optical on the other, in a single enclosure. IBM announced that you can now have DAT160 80GBdrives that is read-write compatible with DAT72 and DDS4 drives, and half-high LTO-4 drives that can read LTO-2 media, and is read-write compatible with LTO-3 media.Read the IBM [Press Release] for details.
Finally, if you are in the United States, Canada or the Carribean, there is a special discount promotionfor tape libraries purchased before June 20, 2008. This includes IBM TS3100, TS3200, TS3310 and TS3500 libraries.See the [Promotion Details] for eligibility.
IBM has added capability to the IBM TotalStorage Productivity Center for Replication. A quick review of the differentoptions for this component.
base Replication (uni-directional from primary to disaster site)
Two-site replication (bi-directional, including failover and failback)
Three-site replication (site awareness for all the copy sessions between all three sites in all situations)
Productivity Center for Replication supported all these levels for DS8000, DS6000 and ESS 800 disk models, butfor SVC it only supported FlashCopy and Metro Mirror for the uni-directional base. IBM announced version 3.4 today that has added support for SVC for Global Mirror (asynchronous disk mirroring) and bi-directional failover/failback. This supports lets you have "practice volumes" that allow IT managers to perform "disaster recovery exercises" without disrupting production workloads.
Also, for the DS8000, there is support for the new Space Efficient FlashCopy and DynamicVolume Expansion features. Here is the IBM
The Productivity Center for Replication server can run on either a Windows/Linux-x86 server or a z/OS mainframe server.The Productivity Center for Replication on System z offers all the same new support for SVC and DS8000, as well asincorporated Basic HyperSwap capability that I mentioned in my post last February[DS8000 Enhancements for the IBM System z10 EC].
Here are the IBM press releases for the TotalStorage Productivity Center for Replication on[Windows/Linux-x86and System z] servers.
I'm at a Business Partner conference today, discussing these announcements and other topics, so need to go back to those festivities.
Well it's Tuesday, which means its time to look at recent announcements.While I was on vacation last week, IBM made a lot of storage announcements October 23.Josh Krischer gives his summary on WikiBon [October 2007 Review].Austin Modine of the The Register went so far as to say that [IBM goes crazy with storage system updates].
IBM System Storage DS8000 series
This is "Release 3" software/microcode upgrades on our existing "Turbo" hardware.
IBM FlashCopy SE -- Here "SE" stands for Space Efficient. Rather than allocating a full 100% of the space for the FlashCopy destination, you can set aside just a fraction, and this will hold all the changed blocks, similar to whatIBM already offers on the DS4000 series.
Dynamic Volume Expansion -- In the past, if you needed more space for a LUN, you had to carve out a newer one elsewhere, and then copy the data over from the old to the new, leaving the old LUN around to be re-used or leftstranded. With this enhancement, you can just upgrade the LUN in place, making it bigger as needed, similar to whatIBM already offers on the DS4000 series and SAN Volume Controller. This applies to CKD volumes for the System zmainframe users out there as well.
Storage Pool Striping -- striping volumes across RAID ranks to eliminate or reduce hot-spots, and provide betterload balancing. Many used SAN Volume Controller in front of the DS8000 to do this, but now you can do it natively inthe DS8000 itself.
z/OS Global Mirror Multiple Reader -- for System z customers, "z/OS Global Mirror" is the new name for XRC. Thisenhancement improves the throughput of sending updates to the remote disaster recovery location.
DS Storage Manager enhancements, the element manager software has been enhanced, and is pre-installed on the new IBM System Storage Productivity Center, which I will talk about below.
Intermix of DS8000 machine types -- this is especially useful to allow new frames to have co-terminating warrantieswith the base units. In other words, as you expand your system, you can ensure that the entire chunk of iron runs outof warranty all at the same time, to simplify your decision making process to upgrade or contract for extended service.
One of the biggest complaints about IBM TotalStorage Productivity Center is that it is software that needs to beinstalled on its own server, and that this installation process can take a day or two. Why wait? Now you can havea hardware console that has the DS8000 Storage Manager software, SVC Admin Console software, and IBM TotalStorageProductivity Center "Basic Edition" pre-installed. Here are the key features.
Pre-installed and tested console
DS8000 R3 GUI integration
Cohabitation of SVC 4.2.1 GUI and CIMOM
Automated device discovery
Asset and capacity reporting, including tape library support
Our "Release 9" applies across the board, from N3000 to N5000 to N7000 series models, includingnew host bus adapters, and the new Data OnTAP 7.2.4 release level.
The Virtual File Manager (VFM) was announced as one of our latest [Storage Virtualization Solutions]. VFMprovides a global namespace that aggregates the file systems from Linux, UNIX, and Windows file servers, as well asN series storage, into a consolidated environment.
IBM's virtual tape library (VTL) for the distributed systems platform, has been enhanced to provide:
Up to 12TB of disk cache, using 750GB SATA disk.
F05 Tape Frames installed as TS7520 base units through a 32 port fibre channel switch
Support for LTO generation 4 tape drives, both as virtual tape drives and as physical tape drives within IBM automated tape libraries attached to the TS7520. This allows you to use Encryption capabilities of LTO4.
DS3000 series now supports SATA disk, and can be attached to AIX and Linux on System p servers. This appliesto the DS3200, DS3300 and DS3400 models.See the [DS3000 Announcement Letter] for more details.
The proof-of-concept that IBM Haifa research center developed back in 1998 became what we now call the iSCSI protocol.The book iSCSI: The Universal Storage Connection introduces the history as follows:
In the fall of 1999 IBM and Cisco met to discuss the possibility of combining their SCSI-over-TCP/IP efforts. After Cisco saw IBM's demonstration of SCSI over TCP/IP, the two companies agreed to develop a proposal that would be taken to the IETF for standardization.
There are three ways to introduce iSCSI into your data center:
Through a gateway, like the IBM System Storage N series gateway, that allows iSCSI-based servers connect to FC-based storage devices
Through a SAN switch or director, a FC-based server can access iSCSI-based storage, an iSCSI-based server accessing FC-based storage, or even iSCSI-based servers attaching to iSCSI-based storage.
Directly through the storage controller.
IBM has been delivering the first method with its successful IBM System Storage N series gateway products, buttoday we have announced additional support for the second and third methods.Here's a quick recap.
New SAN director blades
Supporting the second method, IBM TotalStorage SAN256B Director is enhanced to deliver iSCSI functionality with a new M48 iSCSI Blade, which includes 16 ports (8 Fibre Channel ports; and 8 Ethernet ports for iSCSI connectivity). We also announced a new Fibre Channel M48 Blade which provides 10 Gbps Fibre Channel Inter Switch Link (ISL) connectivity between SAN256B Directors.
With support for Boot-over-iSCSI, diskless rack-optimized and blade servers can boot Windows or Linux over Ethernet,eliminating the management hassles with internal disk.
All of this is part of IBM's overall push into the Small and Medium size Business marketplace, making it easier to shop for and buy from IBM and its many IBM Business Partners, easier to deploy and install storage, and easier tomanage the storage once you have it.
It's Tuesday, which means IBM makes its announcements. We had several for the IBM System Storage product line. Here's a quick recap.
The IBM System Storage DS3000 now offers DC power models.New DC powered models of the DS3200, DS3400, and EXP3000 are well suited for Telco industry environments, as theseare NEBS and ETSI compliant and are powered by an industry standard 48 volt DC power source.
Also, the IBM System Storage N series now supports750GB SATA drives available for the EXN1000 drawer.
IBM Virtualization Engine TS7740now supports 3-cluster grids. Unlike 3-way replication on disk mirroring, such as IBM Metro/Global Mirror for the DS8000 that enforces a primary, secondary and tertiary copy, the grid implementation of TS7740 tape virtualization allows for any-to-any mirroring. Existing standalone TS7740 clusters can be converted to grid-enabled. A "Copy Export" feature allows virtual tapes to be exported onto physical tape. And in keeping with our theme of "enabling business flexibility", performance throughput can now be purchased in 100 MB/sec increments, up to 600 MB/sec, to match your workload bandwidth requirements.
The IBM System Storage TS1120drives installed in the IBM System Storage™ TS3400 Tape Library can now be attached to System z platforms using the IBM System Storage™ TS1120 Tape Controller. Before this, the TS3400 could only be attached to UNIX, Windows and Linux systems.
The IBM System StorageTS2230 Express is offered as an external stand-alone or rack-mountable unit. This model incorporates the new LTO IBM Ultrium 3 Serial Attached SCSI (SAS) Half-High Tape Drive, and a 3 Gbps single port SAS interface for a connection to a wide spectrum of distributed system servers that support Microsoft Windows and Linux systems.
IBM has added theCisco MDS 9124 for IBM System Storageentry-level fabric switch as an Express offering and part of the IBM Express Advantage Program. Express offerings are specifically created for mid-market companies and are well suited for workgroup storage applications like e-mail serving, collaborative databases and web serving. They bring enterprise-class performance, scalability and features to small and medium-sized companies and are easy to use, highly scalable, and cost-effective.This will make it easier for IBM Business Partners to provide fabric switch connectivity for:
Storage consolidation solutions with IBM System Storage™ DS4000 Express disk arrays, especially the DS4700 Express.
Backup / restore solutions with IBM System Storage™ TS3000 Tape Libraries, such as the TS3200.
Archive and Retention
Ordering large configurations of the IBM System Storage Grid Access Manager just got a lot easier.New features enable configurations greater than 500 TB to be submitted as a single order. No change in the actualproduct, just an improvement in the ordering process.
For System p and System i servers, the IBM 3996 Optical library now supports Gen 2 60GB optical cartridges. These can be read/write or WORM cartridges.
I'm off to Denver, Colorado this week. I hope it is cooler there than it is down here in Tucson, Arizona.
Next Monday, September 1, 2008, marks my two year "blogoversary" for this blog!
I won't be blogging on Monday, of course, because that is [Labor Day] holiday here in the United States.
(From a Canadian colleague: US is not the only country who celebrates Labor Day on the first weekend in September. Canada also celebrates Labour Day on the first weekend in September. It's the only holiday(other than Christmas/New Years) where we are in sync with US. Our Thanksgiving Days are different as is your July 4 vs our July 1. But for Labour Day we are one with the Borg...)
(From an Australian colleague: each province of Australia has its own day to celebrate Labor Day, see [Australia Public Holidays])
The rest of the world celebrates Labor Day on May 1, but the USA celebrates this on the first Monday of September, which this year lands on September 1.Originally, the day is intended to be a "day off for working citizens", IBM is kind enough to let managers and marketingpersonnel have the day off also. (Not that anyone is going to notice no press releases next Monday, right?)
I started this blog on September 1, 2006 as part of IBM's big["50 Years of Disk Systems Innovation"] campaign. IBM introduced the first commercial disk system on September 13, 1956 and so the 50th anniversary was in 2006. Last year, IBM celebrated the 55th anniversary of tape systems.
Several readers have asked me why I haven't talked about recent current events, such as the Olympic Games in Beijing, or the U.S. National Conventions for the race for U.S. President. I have to remind them of one of the key precepts of IBMblogging guidelines:
8. Respect your audience. Don’t use ethnic slurs, personal insults, obscenity, or engage in any conduct that would not be acceptable in IBM’s workplace. You should also show proper consideration for others’ privacy and for topics that may be considered objectionable or inflammatory - such as politics and religion.
I made subtle references to my senator from Arizona, John McCain, in my post [ILM for my iPod], and to Barack Obama in my post [Searching for matching information]. I don't think anyone would mind that I send a "Happy Birthday!" wish to both of them.Senator McCain turns 72 years old today, and Senator Obama turned 47 years old earlier this month.
And lastly, Tucson itself [celebrates this entire month] its 233rd birthday. That's right,Tucson, the 32nd largest city of the USA, and headquarters for IBM System Storage, is older than the USA itself.While the Tucson area has been continuously inhabited by humans for over 3500 years, it officially became Tucsonon August 20, 1775.
Fellow blogger Justin Thorp has opined that [blogging is like jogging]. Somedays, you are just too busy to do it, and other days, you make time for it, because you know it is important.For the record, it is not my job to blog for IBM, that ended last September 2007. I continue to blog anyways because I have benefited from it, both personally and professionally.I want to thank all of you readers out there for making this blog a great success! Being named one of the top 10 blogs of the IT storage industry by Network World, two back-to-back Brand Impact awards from Liquid Agency, and recently earning a "31" Technorati ranking, has really helped keep me going.
So, I look forward to next month, and beginning my third year on this blog. I am sure there will be lots of surprises and announcements you can all look forward to in the next coming weeks and months that I will have plenty to write about.
Yesterday (September 7, 2006) the Eclipse Foundation announced that it has approved the creation of the Aperi Storage Management Framework Project.
There's been a lot of confusion out there about Aperi, so I thought I would post some facts and opinions about this exciting new project. A few years ago, I was thelead architect for IBM TotalStorage Productivity Center, IBM's infrastructure management product that helped launch the creation of Aperi.
From the latin word for "open", Aperi is an open source project that aims to simplify the management of storage environments, using the Storage Management Initiative - Specification (SMI-S) open standardto promote interoperability and eliminate complexity in today’s storage environments.
Aperi should provide immediate value upon install with basic storage management capabilities, rather than just simply a collection of components that require costly integration. We've discussed requirements for functions such as:
Resource discovery, monitoring, and reporting
Fabric Topology mapping
Disk / Tape management
Device configuration & LUN assignment
SAN fabric management
Basic asset management
The big confusion most people have is Aperi's relation to SMI-S and the Storage Networking Industry Association (SNIA)open standards group. The best way to explain this is to go backto your High School SAT college-entrance exams. Remember questions like this?
(The answer: a crumb is to bread like a splinter is to wood.)
Aperi is an implementation of SMI-S standard, similar to MySQL or PostgreSQL areopen standard relational database implementations of Structured Query Language (SQL).These compete with proprietary database implementations such as IBM DB2 Universal Database,Oracle Database, Microsoft SQL Server, or Sybase.
Aperi: SMI-S :: PostgreSQL : Structured Query Language (SQL)
It is often the case that the folks writing the code are different than the folks defining the standards. This is the case between the members of Aperi writing code, and the members of the SNIA writing standards. IBM happens tohave employees writing Aperi code, and other employees helping define SMI-S standards.What can I say, IBM is a big company and a leader in many areas.
A good analogyis how the Apache community has developed an awesome web server, and the Firefox Mozillacommunity have developed an awesome web browser, both of which are implementations of the HTTP/HTML standards adopted by the World Wide Web Consortium. Apache and Firefoxcompete with proprietary implementations, such as Microsoft Internet Information Services(IIS) web server and Internet Explorer web browser.
Aperi: SNIA :: Apache : World Wide Web (WWW) Consortium
With this arrangement, Aperi and the SNIA will have very complementary roles in defining and driving standards across the entire storage market. To that end, Aperi will make extensive use of the SNIA’s Technology Center and SNIA’s “plugfests” to test the interoperability of the Aperi framework with the variety of 3rd-party storage offerings available. By providing a tested implementation of SMI-S, Aperi will drive broader industry availability of SMI-S, as well as offer the many benefits of an industry-backed open source community.
Check out this vote of confidence:
"Eclipse's Aperi Project will further advance the adoption of SNIA's SMI-S, benefiting the entire storage industry and IT community. Furthermore, the SNIA and Aperi will define plans to collaborate on new storage standards, standards testing programs, and storage interoperability programs." --- Wayne M. Adams, chair, SNIA Board of directors
So, both proprietary and open source implementations have their place in the world.Proprietary products are needed for advanced, unique value-add, and opensource projects are for basic support focused on interoperability and flexibility.These can be combined, for example, proprietary "plug-ins" built on an open source base. The more choices the client has, the better.
Storage vendors benefit too. Vendors are tired of being in the "Y.A.C." business, building "Yet Another Configurator" for each new device developed, with basic functionsto carve LUNs, read performance stats, and so on. By shipping Aperi instead, storagevendors like IBM can invest their development dollars in real innovations, things thatmatter for the customer.
It's Tuesday, which means IBM announcements, and today IBM made some major announcementsthat support a [Dynamic Infrastructure]! I hinted at this yesterday, choosing the week's theme to be all about Cloud Computing and Alternative Sourcing. I will briefly highlight today's announcements related to storage here, and try to go into more detail over the next few weeks.
Ethernet switches and routers
In support of Cloud Computing and Cloud Storage, IBM is now back in theEthernet networking business. This is part of storage as protocols likeiSCSI, CIFS and NFS are gaining prominence. Extending IBM's existing OEMrelationship with Brocade, there are four series:
[c-series] - "c" for Compact, these are 1U high fixed port switches
[g-series] - "g" for Pay-as-you-Grow using IronStack stacking technology to allow up to 8 switches to be glommed, glued, er.. "gathered" together as a single virtual chassis.
[m-series] - "m" for Multiprotocol Label Switching [MPLS] which supports routing between LAN and WAN networks over OC12 and OC48 lines.
[s-series] - "s" for slots, the B08S has eight slots, and the B16S has sixteen slots, supporting up to 384 ports. These models support Power-over-Ethernet [PoE] that simplifies attaching Voice-over-IP (VoIP) telephones and IP-based surveillance cameras.
IBM announced it will strengthen its partnership with Juniper Networks, and continues to consider Cisco a strategic partner as well. To help customer position themselves for Cloud Computing and Cloud Storage,IBM also launches some new services:
The IBM [DS5000] now supports self-encrypting disk drives, known also as "full-disk encryption" or FDE, for added security, and 8Gbps Fibre Channel (FC) ports for added performance. The DS5300 model in particular now supports up to 448 disk drives for added scalability.
Comprehensive Data Protection Solution
IBM's [Data Protection Solution] shows off IBM's awesome synergy between servers, storage and software. Combining System x servers, Tivoli Storage Manager FastBack software, and DS5000, DS4000 or DS3000 series disk systems. The solution is designed to both Windows-based servers and their applications, offering bare metal restores, and application–level protection for Oracle, SQL, Exchange and SAP.
Tivoli Storage Productivity Center
Last February, IBM previewed the renaming of TotalStorage Productivity Center to its new name,Tivoli Storage Productivity Center. Today, IBM announces [Tivoli Storage Productivity Center v4.1]. Some key changes include:
Productivity Center for Fabric has been merged into Productivity Center for Disk
Productivity Center for Replication is now integrated, but remains separately licensed
Productivity Center can now feed input to IBM's Novus Storage Enterprise Resource Planner [SERP]
TS7650 ProtecTIER Data Deduplication IP-based replication
IBM previews IP-based replication which allows the TS7650 appliance or TS7650G gateway to sendvirtual tape data over to a remote location. This is instead of having the underlying disk systemsperform the replication on its behalf. Having the TS7650 do the replication is preferred, as itcan maintain virtual cartridge integrity, when a virtual tape is unmounted the replication can beginat that point.
As a consultant, I am often asked to help design the architecture for the information infrastructure. A usefulanalogy to gather requirements and preferences is the difference between area rugs and wall-to-wall carpeting. Arearugs are not secured to the floor and cover only a portion of the floor area. Carpets are generally tacked or cemented to the floor, often with an underlay of cushion padding, stretched across the entire floor surface, out to all four walls of each room.
Each has its pros and cons, and often is a matter of preference. Some people like area rugs because they can choosea different style for each room, match the decor and color scheme of furniture, and use these to define each livingspace. Ever since paleolithic man put animal skins on the floor of their cave, people recognize that cold, hard andugly floors could be covered up with something soft and more attractive.Others prefer wall-to-wall carpeting because they want to walk around the house barefoot, have their young children crawl on their hands and knees, and give the entire house a unified look and feel. This is often an inexpensive option when compared against the cost of individual rugs.
The same is true for an information infrastructure. For some, they prefer the "area rug" approach: this style ofstorage for their email, this other type of storage for their databases, and perhaps a third for their unstructuredfile systems. When customers ask what storage would I recommend for their SAP application, or their Microsoft Exchangeemail environment, or their Business Intelligence (BI) software, I recognize they are taking this "area rug" approach.
Like area rugs, having different storage can focus on specific attributes of the workload characteristics. It alsoinsulates against company-wide changes, the dreaded "rip-and-replace" of replacing all of your storage with somethingfrom a different vendor. With "area rug" storage, you can support a dual-vendor or multi-vendor strategy, and upgrade or replace each on its own schedule.
Thanks to open standards and industry-standard benchmarks, changing out one storage solution for another is assimple as rolling up an area rug, and putting another one in its place that is similar in size dimensions.
Others may prefer "wall-to-wall carpeting" approach: one disk system type, one tape library type,one network type, that provides unified management and minimizes the needs for unique skills. Generally, the choice of NAS, SAN or iSCSI infrastrucutre is done company-wide, and might strongly influence the set of products that will support that decision. For example, those with a mix of mainframe and distributed servers looking for SAN-attached storage may look at an [IBM System Storage DS8000] and [TS3500 tape library] that can provide support for FICON and FCP.
Those looking at NAS or iSCSI might consider the IBM System Storage N series products, "unified storage" supporting iSCSI, FCP and NAS protocols. If you want the "wall-to-wall" to stretch across all the sites in your globally integrated enterprise, IBM's scalable NAS product, Scale-Out File Services[SoFS], provides a global name spacein combination with a clustered file system that provides incredible scalability and performance based on field-proven technology used by the majority of the [Top 100 supercomputer] deployments.
IBM can help you design an information infrastructure that fits either approach.
An article in InformationWeek reports that40,000 ASU Students Leap to Google Apps; University Pays Zero. The ASU president, Michael Crow, wants to make IT the primary driver in his ambitious "New American University" project.Last October, ASU became the first large institution to deploy Google Apps, a comprehensive suite of productivity applications that includes e-mail, search, calendars, instant messaging, and even word processing and spreadsheets.I've tried them out, they work, nothing fancy but certainly good enough for college homework assignments.
Already 40,000 students and faculty have switched their e-mail to Google, while keeping their asu.edu designation. (out of 65,000 student population, which Mr. Crow is trying to raise to 90,000 students!)
E-mail is a thorn in the side of storage administrators. Being "semi-structured" repositories, they cannot just delete or move files around, as there is context between notes and their attachments, that shouldn't be broken. E-mail systems are often the fastest growing consumer of storage for many organizations.
Switching from maintaining their own mail servers to Google is saving ASU $500,000 US dollars alone, not including the administrator labor savings. Again, some corporations might feel their e-mail is too "secret" to be outsourced like this, but for college students who spend all their creative talent posting things on MySpace and YouTube, and faculty who spend their careers TRYING to get published, they have nothing to hide from the rest of the world. It makes perfect sense.
Best of all, Google isn't charging ASU anything for this service. Google is able to cover the costs from advertising revenue instead. I can think of a lot of companies that might want to advertise to a demographic of "40,000 students who are mostly 18-25 years old and all live in or near Tempe, AZ".
This week I was in Palm Springs in meetings with clients, prospects, business partners and IBM sales reps.
Tuesday consisted of "outdoor meetings", but the high winds caused some people to arrive late, and others to land in the various sand traps and water hazards. A "welcome reception" event allowed everyone to socialize and get to know the IBM experts and executives. Two of my colleagues, Mike Stanek and Dave Wyatt, were with me also in Australia last week, and so the three of us were discussing recovery from jet lag.
Wednesday was organized as a main tent event, where everyone met into one large room to hear our strategy,latest set of offerings, and customer testimonials. This was done indoors, of course, which was a good thing as the winds were now gusting up to 50 miles per hour, knocking over windmills and making the local news.
Here's a quick sample from the testimonials:
An insurance company virtualized their IBM DS8000, DS4000, ESS 800 and EMC DMX3 high-end disk with theIBM System Storage SAN Volume Controller and got higher availability and performance. Data migrationefforts that used to take six(6) hours of admin time now took less than one hour, and with no system downtime.They have a total of 350TB virtualized under SVC now, but plan to extend this for a variety of other projects.
A bank presented their success using "Global Mirror" (IBM's asynchronous two-site replication disk mirroring capability).Their previous "business continuity" plan was called 2-20-24 for 2 sites that were 20 miles apart and recovery time objective (RTO) of 24 hours. With the events of Hurricane Katrina, this was considered inadequate, and a new2-200-6 plan was requested, across 200 miles with a recovery time objective of only 6 hours. The chose to deploythis one application at a time, to learn and grow by experience in each phase. They started with Microsoft Exchange e-mail application running under VMware on BladeCenter servers, and wereable to recover remotely within 1 hour. They are now looking to refine and automate the recovery process, perhapswith IBM TotalStorage Productivity Center for Replication and Geographically Dispersed Open Clusters (GDOC).
A healthcare provider presented their success with tiered storage, managing a 475TB mix of IBM DS8000, DS6000,DS4000 and HP EVA disk arrays. The key was having centralized storage management from IBM, which allowedthem to shrink provisioning time from 3 weeks average, to now 96% of their storage provisioning requests are completedin less than 1 week. Moving data between storage tiers was non-disruptive, and the significantcosts savings greatly justified the change in "mindset" that required some training on the new environment.
Thursday we offered a series of "workshops" on specific topics. These were interactive sessions to discuss installation, design and deployment of various solutions. The event ended early enough so that people couldreturn home, or go to the practice range, which reminded me of this inspiring video on How to play golf as well as Tiger Woods.
The event got great reviews, and I look forward to the next one. Until then, enjoy the weekend!
For those of you worried about my mysterious absence on the blogosphere, I am getting better. Sorry for not posting much lately, I have had more serious issues to worry about. I am awaiting results on whether I have Dengue fever from Brazil, Avian flu from Thailand, Malaria from Kenya, or perhaps it is just food poisoning from the otherwise fabulous French cuisine I ate last week in the South Pacific. Well, I am back in town for a while, and hopefully will recover to full health, and have some time to reflect my thoughts on storage topics.
Speaking of which, a lot has happened while I was out. Let's take a quick look.
Following our introduction of the world's first encryption-capable tape drive, the TS1120, IBM now offers higher capacity 700GB cartridges, in standard 3592 format.
The DS8000 Turbo disk system now is being offered with a flexible choice of warranty periods, 1-year, 2-year, 3-year and 4-year. Since IBM was the only one to offer 4-year warranties, it was sometimes difficult to compare apples-to-apples with our competition that offered lesser warranty periods. Now, we can match the warranty period you need, so the focus can shift on the added value the DS8000 Turbo provides at the right price.
IBM's newest low-end half-high tape drive, the TS2230 Tape Drive Express Model H3L, part of our Express portfolio of offerings designed for small and medium-sized businesses (SMB). It supports the latest LTO Generation 3 specification, so fully compatible with our larger tape systems, as well as the LTO-based gear from HP and Quantum.
A few weeks ago, my Tivo(R) digital video recorder (DVR) died. All of my digital clocks in my house were flashing 12:00 so I suspect it wasa power strike while I was at the office. The only other item to die was the surge protector,and so it did what it was supposed to do, give up its own life to protect the rest of myequipment. Although somehow, it did not protect my Tivo.
I opened a problem ticket with Sony, and they sent me instructions on how to send itover to another state to get it repaired.Amusingly, the instructions included "Please make a backup of the drive contents beforesending the unit in for repair." Excuse me? How am I supposed to do that, exactly?
My model has only a single 80GB drive, and so my friend and I removed the drive and attachedit to one of our other systems to see if anything was salvageable. It failed every diagnostictest. There was just not enough to read to be usable elsewhere.
This is typical of many home systems. They are not designed for robust usage, high availability, nor any form of backup/recovery process. Some of the newer models havetwo drives in a RAID-1 mode configuration, but most have many single points of failure.
And certainly, it is not mission critical data. Life goes on without the last few episodesof Jack Bauer on "24", or the various Food Network shows that I recorded for items I planto bake some day. For the past few weeks, I have spent more time listening to the radioand reading books. Somehow, even though my television runs fine without my Tivo, watchingTV in "real time" just isn't the same.
I suspect that if you gave someone a method to do the backup, most would not bother to useit. People are now relying more and more heavily on their home-basedinformation storage systems, digital music, video and cherished photographs. Perhaps experiencing a "loss" will help them appreciate backup/recovery systems so much more than they do today.
The author is wondering whether EMC will try to avoid the fate of Hitachi's mainframebusiness, focusing on "moving into the IBM field" of offering software and services for more complete solutions.
Interestingly, one comment opines that EMC's acquisition of Documentum was "followed" byIBM's acquisition of FileNet, not realizing that IBM already has the leading documentmanagement software (IBM Content Manager).
Another comment cites IBM's recent push of Xen asanother example "following" EMC's acquisition of VMware, again not realizing that IBM has hadLogical Partition (LPAR) capability in its System z, System p and System i server lines formany years.
On his blog post on preparation, Seth Godin mentioned an appropriate Swedish saying:
There is no bad weather, just bad clothing.
Appropriate because it snowed here in Tucson, Arizona on Sunday evening, leaving many of us here figuring out how to drive through the stuff on Monday. In my entire lifetime, I have only witness snow down in the Tucson valley a handful of times. It got me thinking about coats, and the wonderful schemes for coat check rooms, as an analogy for data access. A lot of people ask me to compare and contrast one technology from another, say block-level virtualization from content-addressable storage, and so on, and I always try to find a good analogy to help explain things.
Let's start with the setting. It is snowing outside and people are wearing coats. When they come inside, they check their coats at a coat check room, a large room with rows and rows of racks with hangers. A coat check attendant takes your coat and puts it on a hanger, and gives you a ticket or other identifier that will allow you to retrieve your coat later. The ticket must have sufficient information to retrieve the coat quickly, rather than searching rows and rows of hangers for it.
Block-based disk storage
You walk to the coat-check desk, tell the attendant to hang your coat on a specific hanger, say hanger number 387. When you come back, you ask for the coat on hanger 387. The coat-check attendant knows exactly where hanger 387 is, and is able to retrieve it quickly. Most disk systems use this approach, including IBM SAN Volume Controller and DS family of disk systems.
Name-based disk storage
You walk to the coat-check desk, tell the person the name that you want to call your coat. An empty hanger is located, and a list of coat names, with their associated hanger number, is then kept. Upon return, you ask for your coat by name, and the coat-check attendant looks up the hanger number to match, and retrieves your coat. This is the scheme used by the IBM System Storage DR550, N series for NAS storage, and the IBM Healthcare and Life Sciences Grid Medical Archive Solution (GMAS).
Content-addressable storage (CAS)
You walk to the coat-check desk and hand them your coat. The attendant weighs your coat, checks the brand, the size, the number of buttons and zippers, types it all in, and the computer spits out a "hash code" from 1 to 99999. An empty hanger is found, and the hash code is associated to the hanger number. Upon return, you provide the hash code you were given, and the coat-check attendant looks up the hanger number to match, and retrieves your coat.This is the scheme used for some non-erasable, non-rewriteable storage, such as the EMC Centera.
IBM invented hash codes in 1953 as a way to speed up searches. For example, if you want to look up a word in the dictionary, knowing the first letter of the word makes it much quicker, because you can thumb directly to that section. A hash code was intended to give a more even distribution, so that if a million words are stored in a "hash code dictionary" then you would calculate the hash code, then look up only that section of words associated with that specific hash code number.
A problem arises when you generate "hash codes" for storage. It is possible for two different pieces of data to resolve to the same hash code. When an application tries to write a piece of data, and it resolves to a hash code that already exists, that is called a collision. One response is to either compare the incoming data to the data that is already stored, confirm they are identical, but that can be time consuming. The other response is to just assume they are identical, and reject the secondary copy, a process often referred to as "de-duplication".
What's the chance of getting a collision for data that is really different? Let's take for example the famousBirthday paradox. Suppose the coat check room assigned the hanger based on your birthday (month and day). How may coats before you run the risk of having two people turn in coats with the same birthday? After only 23 people, the likelihood is 50%. At 60 people, it goes up to 99%.
For this reason, IBM does not offer content-addressable storage. For non-erasable, non-rewriteable storage, the IBM System Storage DR550 requires the application to give each object a name, and that name is then used to storage the data, eliminating the possibility that data might accidently be thrown away.
Continuing this week's theme on Business Continuity, I will use this post to discuss this week'sIBM solid state disk announcement.This new offering provides a new way to separate programs from data, to help minimizedowntime and outages normally associated with disk drive failures.
Until now, the method most people used to minimize the amount of data on internalstorage was to use disk-less servers with Boot-Over-SAN, however, not all operating systems, and not all disk systems, supported this.
Windows, however, is not supported, because of the small 4GB size and USB protocol limitations. For Windows, you would add a SAS drive, you boot from this hard drive, and use the 4GB Flash drive for data only.
So what's new this time? Here's a quick recap of July 17 announcement. For the IBM BladeCenter HS21 XM blade servers, new models of internal "disk" storage:
Single drive model
A single 15.8GB solid-state disk drive, based on SATA protocol. In addition to theLinux operating systems mentioned above, the capacity and SATA protocols allowsyou to boot 32-bit and 64-bit versions of Windows 2003 Server R2, with plans in placeto other platforms in the future, such as VMware. I am able to run my laptop Windows with only 15GB of C: drive, separating my data to a separate D: partition, so this appears to be a reasonable size.
Dual drive model
The dual drive fits in the space of a single 2.5-inch HDD drive bay.You can combine these in either RAID 0 or RAID 1 mode.
RAID 0 gives you a total of 31.6GB, but is riskier. If you lose either drive,you lose all your data. Michael Horowitz of Cnet covers the risks of RAID zerohere andhere.However, if you are just storing your operating system and application, easily re-loadable from CD or DVD in the case of loss, then perhaps that is a reasonable risk/benefit trade-off.
RAID 1 keeps the capacity at 15.8GB, but provides added protection. If you loseeither drive, the server keeps running on the surviving drive, allowing you to schedule repair actions when convenient and appropriate. This would be the configuration I would recommend for most applications.
Until recently, solid state storage was available at a price premium only. Flash prices have dropped 50% annually while capacities have doubled. This trend is expected to continue through 2009.
According to recent studies from Google and Carnegie Mellon, hard drives fail more oftenthan expected. By one account, conventional hard disk drives internal to the server account for as much as 20-50% of component replacements.IBM analysis indicates that the replacement rate of a solid state drive on a typical blade server configuration is only about 1% per year, vs. 3% or more mentionedin the these studies for traditional disk drives.
Flash drives use non-volatile memory instead of moving parts, so less likely to break down during high external environmental stress conditions, like vibration and shock, or extreme temperature ranges (-0C° to +70°C) that would make traditional hard disks prone to failure.This is especially important for our telecommunications clients, who are always looking for solutions that are NEBS Level 3 compliant.
As with any SATA drive, performance depends on workload.Solid state drives perform best as OS boot devices, taking only a few secondslonger to boot an OS than from a traditional 73GB SAS drive. Flash drives also excel in applications featuring random read workloads, such as web servers. For random and sequential write workloads, use SAS drives instead for higher levels of performance.
Part of IBM's Project Big Green, these flash drives are very energy efficient. Thanks to sophisticated power management software, the power requirement of the solid state drive can be 95 percent better than that of a traditional 73GB hard disk drive. These 15.8GB drives use only 2W per drive versus as much as 10W per 2.5” hard drive and 16W per 3.5” hard drive. The resulting power savings can be up to 1,512 watts per server rack, with 50% heat reduction.
So, even though this is not part of the System Storage product line, I am very excitedfor IBM. To find out if this will work in your environment, go to the IBM Server Provenwebsite that lists compatability with hardware, applications and middleware, or review the latest Configuration and Options Guide (COG).
This week I am in Maryland, teaching at our Top Gun sales training class.
Of course, often it is the students teaching me something new. Bringing up freshnew ways at looking at things.
Take for example this new online video game called Capacity Crisis. In it, you are the storage administrator tryingto get additional storage capacity to all the different departmentmanagers that need more space.
I have created blog categories, based on our System Storage offering matrix, which you can track individually:
Disk systems, including the IBM System Storage DS Family of products, SAN Volume Controller, N series, as well as features unique to these products, such as FlashCopy, MetroMirror, or SnapLock. Tape
Tape systems, including the IBM System Storage TS Family of products, tape-related products in the Virtualization Engine portfolio, drives, libraries and even tape media.
Storage Networking offerings, from Brocade, McData, Cisco and others, such as switches, routers and directors.
Infrastructure management, including IBM TotalStorage Productivity Center software, IBM Tivoli Provisioning Manager, IBM Tivoli Intelligent Orchestrator, and IBM Tivoli Storage Process Manager.
Business Continuity, including IBM Tivoli Storage Manager, Tivoli CDP for Files, Productivity Center for Replication software component, Continuous Availability for Windows (CAW), Continuous Availability for AIX (CAA).
Lifecycle and Retention offerings, including our IBM System Storage DR550, DR550 Express, GPFS, Tivoli Storage Manager Space Management for UNIX, Tivoli Storage Manager HSM for Windows, and DFSMS.
Storage services, including consulting, assessments, design, deployment, management and outsourcing.
This is great news for everyone. I have said before that VMware is perhaps the best product EMC offers, and some EMC bloggers have returned the favor saying that SVC might just be the best disk system that IBM offers. While IBM and EMCare heavily competitive in other aspects of the IT storage industry, when it comes to delivering what is right for the customer, we can set aside those differences. IBM is the number one reseller of VMware, and it is a great pairing with SAN Volume Controller.
Of course, it is not a free-for-all. VMware has a few restrictions at this time:
The VMware certification is limited to Windows operating system, specifically those listed on its [Guest OS Guide].The list looks fairly extensive, so if you were running Windows guests on VMware to SVC today via RPQ,you are probably covered. However, if you are running NetWare or Linux, then the VMware certification doesnot yet apply.
host bus adapters
Only Qlogic host bus adapters are supported at this time. This is because VMware directly communicates to the host bus adapters as part of its "I/O virtualization" capabilities, and needs to work with or test with all the other HBA manufacturers.
no RDM support
Raw Device Mapping (RDM) mode is currently not yet supported. This probably will only affect a small percentage of customers, as I don't know of any major applications that require this.
Of course, most of these issues can probably be addressed with additional testing, or minor software changes, and IBM will work with VMware to prioritize what added testing or software changes are needed to expand this support.
Whew! I am glad that is over. The BarryB circus has left town, he has decided to [move on to other topics], and I am now to clean up the ["circus gold"] leftbehind. I would like to remind everyone that all of these discussions have been about the architecture,not the product. IBM will come out withits own version of a product based on Nextra later in 2008, which may be different than the product that XIV currentlysells to its customers.
RAID-X does not protect against double-drive failures as well as RAID-6, but it's very close
BarryB calls this the "Elephant in the room", that RAID-6 protects better against double-drive failures. I don't dispute that. He also credits me with the term "RAID-X", but I got this directly from the XIV guys. It turns out this was already a term used among academic research circles for [distributed RAID environments]. Meanwhile, Jon Toigo feels the term RAID-X sounds like a brand of bug spray in his post[XIV Architecture: What’s Not to Like?]Perhaps IBM can change this to RAID-5.99 instead.
If you measure risk of a second drive failing during the rebuild or re-replication process ofa first drive failure, you can measure the exposure by multiplying the amount of GB at risk by thenumber of hours that the second failure could occur, resulting in a unit of "GB-hours". Here Ilist best-case rebuild times, your mileage may vary depending on whether other workloads existon the system competing for resources. Notice that 8-disk configurations of RAID-10 and RAID-5for smaller FC disk are in the triple digits, and larger SATA disk in five digits, but that with RAID-X it is only single digits. That is orders of magnitude closer to the ideal.
For each RAID type, the risk is proportional to the square of the individual drive size.Double the drive size causes the risk to be four times greater.This is not the first time this has been discussed. In [Is RAID-5 Getting Old?], Ramskovquotes NetApp's response in Robin Harris' [NetApp Weighs In On Disks]:
...protecting online data only via RAID 5 today verges on professional malpractice.
As disks get older, RAID-6 will not be able to protect against 3-drive failures. A similar chartabove could show the risk to data after the second drive fails and both rebuilds are going on,compared to the risk of a third drive failure during this time. The RAID-X scheme protects muchbetter against 3-drive failures than RAID-6.
Nothing in the Nextra architecture prevents a RAID-6, Triple-copy, or other blob-level scheme
In much the same way that EMC Centera is RAID-5 based for its blobs, there is nothing in the Nextra architecturethat prevents taking additional steps to provide even better protection, using a RAID-6 scheme, making three copiesof the data instead of two copies, or something even more advanced. The current two-copy scheme for RAID-X is betterthan all the RAID-5 and RAID-10 systems out in the marketplace today.
Mirrored Cache won't protect against Cosmic rays, but ECC detection/correction does
BarryB incorrectly states that since some implementations of cache are non-mirrored, that this implies they are unprotected against Cosmic rays. Mirroring does not protect against bit-flips unless both copies arecompared for differences. Unfortunately, even if you compared them, the best you can do is detect theyare different, there is no way of knowing which version is correct.Mirroring cache is normally done to protect uncommitted writes. Reads in cacheare expendable copies of data already written to disk, so ECC detection/correction schemes are adequateprotection. ECC is like RAID for DRAM memory. A single bit-flip can be corrected, multiple bit-flipscan be detected. In the case of detection, the cache copy is discarded and read fresh again from disk.IBM DS8000, XIV and probably most other major vendor offerings use ECC of some kind. BarryB is correctthat some cheaper entry-level and midrange offerings from other vendors might cut corners in this area.I don't doubt BarryB's assertion that the ECC method used in the EMC products may be differently implemented than theECC in the IBM DS8000, but that doesn't mean the IBM DS8000's ECC implementation is flawed.
ECC protection is important for all RAID systems that perform rebuild, and even more importantthe larger the GB-hours listed in the table above.
XIV is designed for high-utilization, not less than 50 percent
I mentioned that the typical Linux, UNIX or Windows LUN is only 30-50 percent full, and perhaps BarryBthought I was referring to the typical "XIV customer". This average is for all disk storage systems connectedto these operating systems, based on IBM market research and analyst reports. The XIV is expected to run at much higher utilization rates, and offers features like "thin provisioning" and "differential snapshot" to make this simple to implement in practice.
Most often, disks don't fail without warning. Usually, they give out temporary errors first, and then fail permanently.The XIV architecture allows for pre-emptive self-repair, initiating the re-replication process after detecting temporary errors, rather than waiting for a complete drive failure.
I had mentioned that this process used "spare capacity, not spare drives" but I was notified that there are three spare drives per system to ensure that there is enough spare capacity, so I stand corrected.
New drives don't have to match the same speed/capacity as the new drives, so three to five years from now, whenit might be hard to find a matching 500GB SATA drive anymore, you won't have to.
No RAID scheme eliminates backups or Business Continuity Planning
The XIV supports both synchronous and asynchronous disk mirroring to remote locations. Backup software willbe able to backup data from the XIV to tape. A double drive failure would require a "recovery action", eitherfrom the disk mirror, or from tape, for the few GB of data that need to be recovered.
A third alternative is to allow end-users to receive backups of their own user-generated content. For example, I have over 15,000 photos uploaded over the past six years to Kodak Photo Gallery, which I use to share with my friends and family. For about $180 US dollars, they will cut DVDs containing all of my uploaded files and send them to me, so that I do not have to worry about Kodak losing my photos.In many cases, if a company or product fails to deliver on its promises, the most you will get is your money back, but for "free services" like HotMail, FreeDrive, FlickR and others, you didn't pay anything in the first place, andthey may point this limitation of liability in the "terms of service".
XIV can be used for databases and other online transaction processing
The XIV will have FCP and iSCSI interfaces, and systems can use these to store any kind of data you want. I mentionedthat the design was intended for large volumes of unstructured digital content, but there is nothing to prevent the use of other workloads. In today's Wall Street Journal article[To Get Back Into the Storage Game, IBM Calls In an Old Foe]:
Today, XIV's Nextra system is used by Bank Leumi, a large Israeli bank, and a few other customers for traditional data-storage tasks such as recording hundreds of transactions a minute.
BarryB, thanks for calling the truce. I look forward to talking about other topics myself. These past two weeks have been exhausting!
Today, I went looking for reading-glasses. Unfamiliar with my surroundings, I asked several people where I might be able to find and purchase these, and was sent in various directions. My first stop was a bookstore. It would make sense that since many people need reading glasses to read the books, that they would sell them there, but no. The staff didn't know where I could go, but pointed me in the direction of a mall. At the mall, I found a pharmacy. Many pharmacies sell reading glasses, so I stopped in, but no, not this one. The pharmacists suggested the super-store nearby. I walked in to the super-store, and asked the first employee where they keep their reading glasses, and they said the other corner. The other corner was the electronics department. It made sense that they sold CDs and DVDs in the same section as the equipment that plays them, but reading glasses? Skeptical, I went to the pharmacy department, and the young and beautiful lady (everyone is young, thin and beautiful here) had me follow her, and she led me back to the electronics department, whereupon she pointed to a rack of sunglasses. I indicated that I need reading glasses, not sunglasses. She pulled one out, and it was indeed reading glasses, 1.25, just what I was looking for. Others were tinted, so you can read the newspaper out in the sunlight. The pair I chose cost only $97 in the local currency.
After reading the last sentence, you might be thinking I am describing my "avatar" in Second Life, but no, I am talking about my search for reading glasses on the streets of Mexico. I am here this week in meetings with IBM Business Partners and sales reps to discuss IBM's latest System Storage products and offerings.
We used to tell people they should "clothe" servers with storage. IBM offers both, so yes it makes sense to offer both as part of a complete solution. However, when you look through a dictionary definition "to clothe" you learn it is to dress, wrap or cover with clothing, an implication that it is external, and perhaps temporary, easily changed, like switching from sunglasses to reading glasses. In Second Life, objects can be "worn", simply by attaching or detaching them to your "avatar". Sometimes clothing serves a purpose, like reading glasses, provides protection, like raincoats, and other times, more decorative, like"icing on the cake" or "gold plating".
This concept was fine 50 years ago, when we were in a server-centric world, and dumb storage devices were attached to very intelligent servers. Back then, we used the derogatory term "subsystems" to emphasize that storage was just part of the server, not a system of its own.
Today, we live in an information-centric world. The information outlives the media, and the media outlives the servers that access it. It is not unreasonable to attach dozens or hundreds of servers to a single storage system, or collection of storage systems. Over 20 percent of IBM System Storage DS8000 series, for example, are attached to Windows rack-optimized or blade servers. Imagine a refrigerator surrounded by dozens or hundreds of pizza boxes. Storage is no longer a subsystem, but a system on its own right, dressed, wrapped or covered by servers that deliver the right information, to the right people, at the right time.
So perhaps we should reverse it, telling people they should "clothe" their storage with servers!
The results are finally in. IBMer Wolfgang Singer was awarded "Top Speaker" award for his NAS and iSCSI tutorial at last year's Orlando 2006 conference. Here he is receiving the awardfrom SNIA Executive Director Leo Leger.
Of course, NAS and iSCSI technologies have been around for a while, but they are still new formany customers, which is why tutorials like this are so important.
I am in Toronto, Canada. It is a lot cold and rainy here, worse than last week in Seoul, Korea.This looks like a slow news week, so slow that the only news here in Canada is the possibility of anew 5-dollar coin. I thought I would make this week's theme about enterprise applications.
IBM doesn't make these applications anymore, we have decided to focus on our core strength, to be the best IT platform to run other people's applications. This means being the best IT systems, software and services company. However, many of the companies that make enterprise applications are both cooperate and compete against parts of IBM, what we call "coopetition".
Let's take a look at some acronyms in this space:
"Enterprise Resource Planning" represents all the basic applications that business need to run theirbusiness, including: finance, accounting, human resources, and manufacturing. The focus here is to streamline operations and make the workforce more productive. Before IBM, I ran my ownsoftware development company, Pearson Kurath Systems, and we developed ERP applications for clients oneby one, customized to their industry requirements.
"Customer Relationship Management" or sometimes "Client Relationship Management" help companies identifyand retain their customer base. Focus here is to increase customer satisfaction and loyalty.
"Supply Chain Management" help track supply and just-in-time inventory demand, sharing the information withkey suppliers and distributors. The focus is to manage inventories down to nothing, and improve speed to get products out to market.
"Business to Business" refer to procurement, purchase orders, and collecting payments over the internet.One of my pet peeves are acronyms that use "2" to mean "to" and "4" to mean "for".
"Human Capital Management" deals with managing costs of Human Resources (HR) and coordinating servicesfrom outside organizations.
"Knowledge Management" refers to sharing and collaborating information. This is not just email and instant messaging, but also online calendaring, experience repositories, client case studies, and anecdotes.
This week I will cover applications that address these, and how they relate to storage.
This year I resolve to be more consistent in my blogging, and my goal is to give you one to five entries per week, every week, based on the advice from Glenn Wolsey, Jennette Banks, and others.On some weeks, I will have a running theme, so rather than super-long entries to cover everything I can think of on a topic, make the entries short and readable. This week is a good time to review last year's "New Year's Resolutions" and to make new ones for 2007. I will discuss actions that companies can adopt for their data centers.
A common resolution is to lose weight, as in this Dilbert comic. Last year, I resolved to lose weight in 2006, and am delighted with myself that I lost eight pounds. When people ask for the secret of my success, I whisper in their ear "Eat less, exercise more." In general, people (and companies) know what to do, but just don't do it, which Pfeffer and Sutton document in their book The Knowing-Doing Gap. In my case, it involved lifestyle change: I exercised at a gym three times per week in Tucson, with a personal trainer, and revamped my diet.
Not everyone subscribes to the "eat less exercise more" philosophy. For example, Ric Watson argues in his blog that you can eat fewer calories, but eat more in actual volume, by choosing the right foods. This brings up the issues of "metrics" that most data centers are familiar with. Last year, I read the book "You: On a Diet" which explains that it is better to focus on "waist reduction" as measured in inches around your mid-section at the belly button, than "weight reduction" as measured in pounds. This year, I resolve to get down to 35 inches by the end of 2007.
The problem with measuring "weight" is that you are weighing bones, muscle and fat. A person can gain ten pounds of muscle, lose ten pounds of fat, and the scale would indicate no progress. The same problem occurs in data centers. How many TB of data do you have? Storage admins can easily tell you, but can they tell how much of this is bone (data needed for operating infrastructure), muscle (data used in daily operations that generates revenue) or fat (obsolete or orphaned data)?
We at IBM often state that "Information Lifecycle Management (ILM)" is more lifestyle change than a "fad diet". Figuring out what data you should capture in the first place, where to place it, when to move it, and when to get rid of it, is more important that just buying different tiers of storage hardware. So, for those looking to make new data center resolutions, I suggest the following actions:
Re-evaluate the metrics you now use, and determine if they are helpful in making decisions and taking action.
Come up with new ones that are more focused to solve the issues you face.
Consider storage infrastructure software, such as IBM TotalStorage Productivity Center, to help you gather the information about your SAN, disk and tape systems, calculate the metrics, and automate the appropriate actions.
Continuing this week's theme of New Year's Resolutions for the data center, today we'll talk about one that people don't always think about on a personal level, that is to hone your tools and skills.
A long time ago, I used to be a regular speaker at the SHARE user group conference. One of the most attended sessions was Sam Golob presenting the latest CBT Tape set of tools. Over time, this large collection of "mainframe shareware" was handed out on 3480 tape cartridges, then on CDs, and finally made downloadable off the web.Sam's main point, which I remember to this day, was that everyone who has a job should figure out what tools they use, keep those tools functioning properly, and learn to use them well.
Later, I took some cooking classes at a culinary school. Among other things, we learned:
A sharp knife is safer and easier to use than a dull one, resulting in fewer accidents
Knowing what you are doing is the difference between food that is "simply awful" to that which is "awfully simple" to prepare.
A well trained chef can prepare most meals with just a sharp knife and wooden spoon.
The same could be said about software tools. What tools do you use in your job? Do you feel you know how to take full advantage of their power and capabilities?If you develop software, do you know all the features for your debugging tools? If you develop advertising or marketing materials, do you know all the features of your photo or video editing software? If you manage storage in a data center, do you know all the tools for managing your storage area network (SAN), disk systems, tape libraries, and reporting tools to identify all of your files and databases across your entire IT environment?I would not be surprised if you could replace a whole mess of tools with just one, such as the IBM TotalStorage Productivity Center.
Continuing this week's theme of New Year's Resolutions for the data center, today we'll talk about one that many people make for their own personal lives: staying on a budget.
Often, when faced with a tightening budgets, we try to make more use of what we already have. Tell someone they are only using 10 percent of their brain, and they immediatelybelieve you; but tell them they are only using 30 percent of their storage, and they ask for a whitepaper,magazine article, or clarification on how that percentage is calculated. I actually visiteda customer that was only using6 percent of the storage attached to their Windows servers!
So, to help those of you making data center resolutions to stay on budget, the terms to remember are "Reduce", "Reuse" and "Recycle".
When people come to request storage, are they being reasonable about what they need today, or are they asking for what they might need over the next three years? They might need 50GB, but they ask for 100GB, in case they grow, and a year later, you find they have only 15GB of data on it. On the flipside, the person asks for what they need but some storage admins give out more, just so they don't have to be bothered so often when growth happens. Finally, I have seen this formalized into fixed size LUNs, all the disk is carved into big huge 100GB pieces, so if you need 20GB, here's one big enough with plenty of room to grow.
If you are going to keep on a budget, remember that storage today is 30% more expensive than storage next year. That is the average drop in both disk and tape on a dollar-per-MB basis. If there is any way to postpone giving out storage until it is actually needed, you can save a bundle of money. Timing is everything! In the event of a disaster, getting immediate replacement for disk can be very expensive, but if you can wait just two weeks, you can negotiate a better deal. I thought of this while going to the movie theatre yesterday. A "hot dog" and a bottle of water was $8.00, but if you are able to wait two hours and eat after the movie, you can get a much better meal for less.
A lot of companies buy new storage because their existing storage isn't fast enough, or doesn't have the latest copy services. This can easily be solved with an IBM SAN Volume Controller (SVC). The SVC can virtualize slower, functionless storage, and present to your application hosts virtual disks that are faster, and with all the latest disk-to-disk copy services like FlashCopy, Metro Mirror, and Global Mirror.
Chances are, you have unused disk capacity spread across all your storage today, but perhaps they are formatted into small LUNs. The SVC can combine the capacity, and let you carve up big LUNs at the sizes you need.This is like taking all those tiny pieces of soap in your shower and forming a new bar of soap, or taking all the crumbs at the bottom of your bread box, and making a new slice of bread. And, the virtual LUNs are dynamically expandable,so give out only the amount they need today, as it is simple to expand them to larger sizes later.
Of my 13 patents, the first will always be my favorite, on a function called "RECYCLE" for the Data Facility Storage Management Subsystem Hierarchical Storage Manager (DFSMShsm) product, which is now a component of the IBM z/OS operating system. Basically, tapes could contain hundreds or thousands of files, such as backup versions or archive copies, and these expired on different dates. As a result, a tape would be written100 percent full, and then over time, decrease in valid data to 80, 60, 40, 20 until it hit 0 percent. In some cases, a single filecould hold an entire tape hostage. RECYCLE was able to read the valid data off tapes that were perhaps less than 20 percent full, and consolidate them onto fewer tapes. As a result, a whole bunch of tapes could be returned to the scratch pool, and reused immediately for other workloads. This also helps in moving to newer, higher capacity cartridges, such as the new 700GB cartridge that IBM co-developed with FujiFilm.(This RECYCLE function exists in our IBM Tivoli Storage Manager software, as well as our Virtual Tape Server, but is called "reclamation" instead, to avoid confusion on searches.)
When evaluating your use of tape, determine if you are making best use of the tapes you have now, and perhaps a RECYCLE (or reclamation) scheme may be in order. Fewer tapes can save money in many ways, such as reduced storage costs, and reduced courier costs to send the tapes offsite. Tape media can still be 10-20 times less expensive than disk, based on full capacity.
My IBM colleague Marissa Benekos brought her hand-held video camera to [Storage Networking World] conference in Orlando, Florida.I am not there, as I had a conflict with another conference going on here in Tucson, so am relyingon Marissa to feed me information to blog about.
In this segment, she interviews "booth babe" David Bricker. I've known David a long time,and if you are there at the conference, tell him I sent you to visit him at the IBM booth.
David Bricker shows off some of the IBM System Storage product line at SNWin this YouTube video (2 minutes)
Sadly, I can't be in two places at once. SNW is a great conference to attend!
I have arrived safely in Las Vegas for the IBM System Storage and Storage Networking Symposium. This eventis held once every year. The gold sponsors were: Brocade, Cisco, Finisar, Servergraph, and VMware. Our silversponsor was Qlogic.
I presented IBM's System Storage strategy and an overview of our product line. For those who missed it,our strategy is focused on helping customers in four key areas:
Optimize IT - to simplify and automate your IT operations and optimize performance and functionality, through server/storage synergies, storage virtualization, and intergrated storage infrastructure management.
Leverage Information - to enable a single view of trusted business information through data sharing, and to get the most value from information through Information Lifecycle Management (ILM).
Mitigate Risk - to comply with security and regulatory requirements, and keep your business running with a complete set of business continuity solutions. IBM offers a range of non-erasable, non-rewriteable storage, encryption on disk and tape, and support for IT Infrastructure Library (ITIL) service management disciplines.
Enable Business Flexibility - to provide scalable solutions and protect your IT investment through the use of open industry standards like Storage Networking Industry Association (SNIA) Storage Management Initiative Specification (SMI-S). IBM offers scalability in three dimensions: Scale-up, Scale-out, and Scale-within.
IBM has a broad storage portfolio, in seven offering categories:
Disk Systems, including our SAN Volume Controller, DS family, and N series.
Tape Systems, including tape drives, libraries and virtualization.
Storage Networking, a complete set of switches, directors and routes
Infrastructure Management, featuring the IBM TotalStorage Productivity Center software
Business Continuity, advanced copy services and the software to manage them
Lifecycle and Retention, our non-erasable, non-rewriteable storage including DR550, N series with SnapLock, and WORM tape support, Grid Archive Manager and our Grid Medical Archive Solution (GMAS)
Storage Services, everything from consulting, design and deployment to outsourcing and hosting.
I could talk all day on this, but given that the room was packed, every seat taken and the rest of the audience standing along the walls, I had to keep it down to one hour.
SAN Volume Controller Overview
I presented an overview of the IBM System Storage SAN Volume Controller (SVC), IBM's flagship disk virtualizationproduct. Rather than giving a long laundry list of features and benefits,I focused on the five that matter most:
Reduces the cost and complexity of managing storage, especially for mixed storage environments
Simplifies Business Continuity through non-disruptive data migration and advanced copy services
Improves storage utilization, getting more value from the storage hardware you already have
Enhances personnel productivity, empowering storage administrators to get their job done
Delivers high availability and performance
SAN Volume Controller - Customer Success Stories
A good part of this conference are presented by non-IBMers, which include Business Partners and clientssharing their experiences. In this session, we had two speakers share their experiences with SVC.
David Snyder keeps over 80 web sites online and available. His digital media technologiesteam uses SVC to make their storage administration easier, and ensure high availability for web site content creation and publishing.
Mark Prybylski manages storage at his company, a financial bank. His storage management team uses SVC Global Mirror which provides asynchronous disk mirroring between different types of disk, as part oftheir Business Continuity/Disaster Recovery plan.
The last session I attended was "Storage .. to Optimize your ECM depoloyments" by Jerry Bower, now working for IBM as part of our recent acquisition of the Filenet company. ECM stands for Enterprise Content Management, and IBM is the market leader in this space. Jerry gave a great overview of IBM Content Manager software suite, our newly acquired Filenet portfolio, and the storage supported.
After the sessions was a reception at the Solution Center with dozens of exhibitor booths. For example,Optica Technologies had their PRIZM productswhich are able to connect FICON servers to ESCON storage devices.
The IBM Storage and Storage Networking Symposium in Las Vegas continues ...
N series and VMware
Jeff Barnett presented how VMware manages disk image files in its VMfs repository, and how N series offersa better alternative. Virtual machines can access N series volumes directly.
Business Continuity with System i
Allison Pate presented the various Business Continuity options for System i. Many customersuse internal storage for System i, but this then hampers Business Continuity efforts. Instead,you can have IBM System Storage DS8000 or DS6000 series disk systems provide disk mirroringbetween clustered systems.
There was a lot of interest in DR550, one of our many compliance storage solutions. Ron Henkhauspresented an overview of our DR550 and DR550 Express offerings. Unlike the competitive disk-onlysolutions, such as the EMC Centera, the DR550 allows you to attach an automated tape library, managing large amounts of fixed content data at a much lower cost point. It also has encryption, for both diskand tape data.
Open Systems Disk Management
Siebo Friesenborg presented the various steps needed to troubleshoot performance problemswith open systems, including the use of "iostat" on AIX systems as an example, and the stepsyou can take to make formal Service Level Agreements (SLA) between the IT department and thevarious lines of business.
IBM Encryption - TS1120 and LTO-4 encryption comparison
Tony Abete presented TS1120 and LTO-4 encryption techniques. Deploying encryption is more thanjust choosing a tape drive. There are a variety of factors involved, such as whether to managethe keys from the application, the operating system, or the library manager. You need policiesto decided when to encrypt tapes and when not to, generating your keys, storing them, and sharingthem with your business partners, suppliers and service providers with which you send tapes.
I can tell that many people are feeling like they are "drinking from a firehose".IBM's success in storage reaches out to so many different aspects of information management,a variety of industries, and disciplines as varied as regulatory compliance and medical imaging.
The IBM Storage and Storage Networking Symposium continues ...
DS8300 Benchmark for Global Mirror
Phil Allison of Fidelity National Information Services presented his success switching from competition over to IBM DS8300 disk systems for use with Global Mirror. They had usedPerformance Associates famous PAIO driver to help to the benchmarktesting. They ran the benchmars at 2x and 3x their current workloads to see how well the DS8000 performed,measuring IOPS, MB/sec, and millisecond response time (msec). They were very impressed with their results,staying below their target 0.8 msec for most of their runs.
For the Global Mirror, the did a performance "bake-off" between Ciena CN2000 versus Cisco 9216i. These areimplemented differently. Ciena uses a Layer-2 approach, encapsulating the Fibre Channel packets directlyto transport as SDH/SONET or Gigabit Ethernet (GigE), which required dedicated circuits between JacksonvilleFlorida and Little Rock, Arkansas. By contrast, Cisco uses a Layer-3 approach, encapsulating Fibre Channelpackets within an IP packet, which can leverage existing datacenter-to-datacenter backbone.
To add stress to the benchmarks, they used a "Network Impairment" emulator. These artificially inject errors,lose packets, and other signal loss conditions. Running both Cisco and Ciena under these tests help them decide which to purchase, but also enforced that idea that they made the right choice choosing IBM for theirremote distance mirroring solution.
Comparison of Bare Machine Recovery Techniques
"Bare machine recovery" is the phrase used to restore a machine that has no operating system installed (or thewrong operating system). Dave Canan from IBM Advanced Technical Support did a great job reviewing the variousproducts and techniques available, and the pros and cons of each approach. The ones he covered were:
Tivoli Storage Manager - install fresh Windows Operating System, TSM client, and then follow certain steps
Automated System Recovery(ASR) - a new feature of Windows XP and Windows 2003 works with TSM client
Symantec Ghost - formerly callled PowerQuest Drive Image, there are now two versions: Ghost Home Edition and Ghost Corporate Solution Suite
Cristie Bare Machine Recovery(CBMR) - This is an IBM partner that provides both Linux and Windows PE versions. Cristie includes a license for Windows PE, so no need to use the alternative Bart PE method.
SAN Volume Controller - Customer Experience
Bill Giles of Catholic Medical Center, a hospital in New Hampshire, presented his experienceswith IBM System Storage SAN Volume Controller. They have a mix of IBM System x, System p, andSystem i servers, as well as machines from HP, Sun, and Dell. For applications, they havePicture Archiving and Communicatiion System (PACS) for cardiology and radiology, HL7 Interface engine, Clinical Information System, TSM for backup, and Microsoft Exchange fore-mail.
They deployed SVC on AIX, Solaris, Windows 2000 and 2003. They were very delightedwith the results:
Centralized Storage Provisioning
Consolidating disparate storage into a universal platform
Enables non-disruptive data migration
Increased utilization of existing disk resources
Improved disaster recovery with FlashCopy and Metro Mirror
Birds of a Feather (BOF) sessions
We had two BOFs, one for storage attached to System z operating systems, and another for storage attached to Linux, UNIX and Windows systems. This distinctionmade sense when mainframes could only attach to CKD disks and ESCON/FICON tape,and distributed systems could only do FCP/SCSI, but these days, there are all kindsof convergence going on.
Linux on System z can now attach via FCP to LTO tape and SAN Volume Controller, allowing now a wide range of storage options for that platform. z/OS, z/VM, z/VSEand Linux on System z can all access IBM System Storage N series via NFS.
The format was traditional Q&A panel, we had experts at the front of the room,handling the questions and discussion topics brought up by the audience. I'll spareyou the individual questions and answers.
The title of this post is inspired by Baxter Black's [latest book]. Rathera recap of the break-out sessions, I thought I would comment on a fewsentences, phrases or comments I heard in the afternoon and evening.
Stop buying storage from EMC or NetApp
The lunch was sponsored by Symantec. Rod Soderbery presented "Taking the cost out ofcost savings", explaining some ideas to reduce IT costs immediately.
First, he suggested to "stop buying storage" from EMC or NetApp that charge a premiumfor tier-one products. Instead, Rod suggested that people should "think like a Web company"and buy only storage products based on commodity hardware to save money, and to use SRM software to identify areas of poor storage utilization. IBM's TotalStorage Productivity Center softwareis often used to help with this analysis.
His other suggestions were to adopt thin provisioning, data deduplication, and virtualization.The discussion at my table started with someone asking, "How do we adopt those functions without buying new storage capacity with those features already built-in?" I explained that IBM's SAN Volume Controller (SVC),N series gateways, and TS7650G ProtecTIER virtual tape gateway can all provide one or moreof these features to your existing disk storage capacity.
IBM and HP are leaders in blade servers
In the session "Future of Server and OS: Disappearing Boundaries", the audience confirmedby electronic survey that IBM and HP are the leaders in blade servers, although blades representonly 8-10 percent of the overall server market.
Interestingly, 22 percent of the audience has deployed both x86 and non-x86 (POWER, SPARC, etc.) blade servers.The presenters considered this an interesting insight.
Another survey of the audience found that 3 percent considered Sun/STK as their primary storagevendor. One of the presenters was delighted that Sun is still hanging in there.
IBM Business Partners deliver the best of IBM and mask the worst
Elaine Lennox, IBM VP, and Mark Wyllie, CEO of Flagship Solutions Group, Inc. presentedIBM-sponsored back to back sessions. Elaine presented IBM's vision, the New Enterprise Data Center, and the challenges that demand a smarter planet.
Mark focused on his company's experience working with IBM through Innovation Workshops. Theseare assessments that can help someone identify where you are now, where you want to be, andthen action plans to address the gaps.
Cats and Dogs, Oil and Water, Microsoft Windows and Mission-critical applications, what do all of these have in common?
NEC Corporation of America sponsored some sessions on some x86-based solutions they have to offer.The first part, titled "Rats Nests, Snow Drifts and Trailers" focused unified storage, andthe second part, presented by Michael Nixon, focused on how to bring Microsoft Windows servers into the data center for mission-critical applications.
The Economy might be slowing, but storage is still growing
Two analysts co-presented "The Enterprise Storage Scenario". Unlike computing capacity, thereis no on/off switch for storage, not from applications nor from end-users. The cost ofpower for storage is expected to be 3x by 2013. Virtual servers, includingVMware and Microsoft's Hyper-V will drive the need for shared external disk storage.A survey of the audience found 20 percent were expecting to purchase additional storagecapacity 4Q08.
When someone reaches age 52, they expect to coast the rest of their career
At dinner with analysts, the discussion of financial meltdown and bailouts is unavoidable,including everyone's views about the proposed bailout of the Big 3 automakers. I can'tdefend Ford, GM and Chrysler paying their people $70 US dollars per hour, when their UScounterparts at Toyota or Honda are only paid $45 to $50 dollars per hour.
However, I have a close friend who retired after 20 years working for the fire department,and a cousin who retired after 20 years serving in the Navy (the US Navy, not the BolivianNavy), and both are still in their forties in age. A long time ago, IT professionalsretired after 30 years, in some cases with 50 to 60 percent of their base pay as theirpension for the rest of their lives. A 52-year-old that has worked 30 years might expect to enjoy the rest of his old age playing golf and pursuing other hobbies. This is not "coasting", it is called "retirement". The few of my colleagues that I have seen who worked 35 to 40 years did so becausethey enjoyed the challenge of work at IBM. They enjoyed solving tough engineering problems and helping customers.As long as they were having fun on the job,IBM was glad to keep their wealth of experience on board and actively engaged.
Unfortunately, many people rely on their own investments in the stock market for retirement, ratherthan company pensions. With the current financial crisis, I suspect many people my age arereconsidering their previous retirement plans.
We're going to need more trains!
I took the monorail back to my hotel. The ride includes funny announcements and statistics,including this gem:
"Since 1940, Las Vegas has doubled in population every ten years, which means thatby the year 2230, we will have over 1 trillion people calling Las Vegas home. We're goingto need more trains!"
That wraps up Tuesday, Day 2 of my attendance here! Now for some sleep.
This wraps up my week in Las Vegas for the 27th Annual [Data Center Conference]. This conference follows the common approach of ending at noon on Friday, so that attendees can get home to their families for the weekend, or start their weekend in Las Vegas early to watch the 50th annual Wrangler National Finals Rodeo.
I attended the last few sessions. Here is my recap:
Where, When and Why do I need a Solid-State Drive?
The internet provides transport of digital data between any devices. All other uses have evolved from this aim. Increasing data storage on any node on the Web therefore increases the possibilities at every other point. We are just now beginning to recognize the implications of this. The two speakers co-presented this session to cover how Solid State Disk (SSD) may participate.
Some electronic surveys of the audience provided some insight. Only 12 percent are deploying SSD now. 59 percent are evaluating the technology. A whopping 89 percent did not understand SSD technology, or how it would apply to their data center. Here is the expected time linefor SSD adoption:
17 percent - within 1 year
60 percent - around 3 years from now
21 percent - 5 years or later
The main reasons cited for adopting SSD were increasing IOPS, reducing power and floorspace requirements, and expanding global networks. Here's a side-by-side comparison between HDD and SSD:
Disk array with 120 HDD, 73GB drives
Disk array with 120 SSD, 32GB drives
Per 73GB drive
Per 32GB drive
100MB/sec per drive
Read 250 MB/sec per drive Write 170 MB/sec per drive
300 IOPS per drive
35,000 IOPS per drive
12 Watts per drive
2.4 Watts per drive
However, the cost-per-GB for SSD is still 25x over traditional spinning disk, andthe analysts expected SSD to continue to be 10-20x for a while. For now, they estimatethat SSD will be mostly found in blade servers, enterprise-class disk systems, andhigh-end network directors.
The speakers gave examples such as Sun's ZFS Hybrid, and other products from NetApp,Compellent, Rackable, Violin, and Verari Systems.
Taking fear out of IT Disaster Recovery Exercises
The analyst presented best practices for disaster recovery testing with a "Pay Now or Pay Later"pre-emptive approach. Here were some of the suggestions:
Schedule adequate time for DR exercises
Build DR considerations into change control procedures and project lifecycle planning
Document interdependencies between applications and business processes
Bring in the "crisis team" on even the smallest incidents to keep skill sharp
Present the "State of Disaster Recovery" to Senior Management annually
The speaker gave examples of different "tiers" for recovery, with appropriate RPO and RTOlevels, and how often these should be tested per year. A survey of the audience found that70 percent already have a tiered recovery approach.
In addition to IT staff, you might want to consider inviting others to the DR exerciseas reviewers for oversight, including: Line of Business folks, Facilities/Operations, Human Resources, Legal/Compliance officers, even members of government agencies.
DR exercises can be performed at a variety of scope and objectives:
Tabletop Test - IBM calls these "walk-throughs", where people merely sit around the table and discuss what actions they would take in the event of a hypothetical scenario. This is a good way to explore all kinds of scenarios from power outages, denial of service attacks, or pandemic diseases.
Checklist Review - Here a physical inventory is taken of all the equipment needed at the DR site.
Stand-alone Test - Sometimes called a "component test" or "unit test", a single application is recovered and tested.
End-to-End simulation - All applications for a business process are recovered for a full simulation.
Full Rehearsal - Business is suspended to perform this over a weekend.
Production Cut-Over - If you are moving data center locations, this is a good time to consider testing some procedures. Other times, production is cut-over for a week over to the DR site and then returned back to the primary site.
Mock Disaster - Management calls this unexpectedly to the IT staff, certain IT staff are told to participate, and others are told not to. This helps to identify critical resources, how well procedures are documented, and members of the team are adequately cross-trained.
For exercise, set the appropriate scope and objectives, score the results, and then identifyaction plans to address the gaps uncovered. Scoring can be as simple as "Not addressed","Needs Improvement" and "Met Criteria".
Full Speed Ahead for iSCSI
The analyst presented this final session of the conference. He recognized IBM's early leadership in this area back in 1999, with the IP200i disk system. Today, there are many storage vendors that provide iSCSI solutions, the top three being:
23 percent - Dell/EqualLogic
15 percent - EMC
14 percent - HP/LeftHand Networks
This protocol has been mostly adopted for Windows, Linux and VMware, but has been largelyignored by the UNIX community. The primary value proposition is to offer SAN-like functionality at lower cost. When using the existing NICs that come built-in on most servers, iSCSI canbe 30-50 percent less expensive than FC-based SANs. Even if you install TCP-Offload-Engine (TOE) cards into the servers, iSCSI can still represent a 16-19 percent cost savings. ManyIBM servers now have TOE functionality built-in.
Since lower costs are the primary motivator, most iSCSI deployments are on 1GbE. The new10Gbps Ethernet is still too expensive for most iSCSI configurations. For servers runninga single application, 2 1GbE NICs is sufficient. For servers running virtualization with multiple workloads might need 4 or 5 NICs (1GbE), or consider 2 10GbE NICs if 10Gbps is available.
The iSCSI protocol has been most successful for small and medium sized businesses (SMB) lookingfor one-stop shopping. Buying iSCSI storage from the same vendor as your servers makes a lot of sense: EqualLogic with Dell servers, LeftHand software with HP servers, and IBM's DS3300 or N series with IBM System x servers.The average iSCSI unit was 10TB for about $24,000 US dollars.
Security and Management software for iSCSI is not as fully developed as for FC-based SANs.For this reason, most network vendors suggest having IP SANs isolated from your regular LAN.If that is not possible, consider VPN or encryption to provide added security.Issues of security and management imply that iSCSI won't dominate the large enteprise data center. Instead, many arewatching closely the adoption of Fibre Channel over Ethernet (FCoE), based on revised standardsfor 10Gbps Ethernet. FCoE standards probably won't be finalized till mid-2009, with productsfrom major vendors by 2010, and perhaps taking as much as 10 percent marketshare by 2011.
I hope you have enjoyed this series of posts. In addition to the sessions I attended, theconference has provided me with 67 presentations for me to review. Those who attended couldpurchase all the audio recordings and proceedings of every session for $295 US dollars, and those who missed the event can purchase these for $595 US dollars. These are reasonable prices, when you realize that the average Las Vegas visitor spends 13.9 hours gambling, losing an average of $626 US dollars per visit. The audio recordings and proceedings can provide more than 13.9 hours of excitement for less money!
Well, I am back from Las Vegas, and had a pleasant [US Memorial Day] holiday yesterday.
Today is Tuesday, and that means more IBM announcements! IBM announced that the DCS9900 now supports an intermix of SAS and SATA drives. The DCS9900 is purpose-built specifically for the High-Performance-Computing (HPC) and Video Broadcasting industries.
The system is a combination of 4U controllers and 3U expansion drawers. The controllers handle either FC or Infiniband attachment to host servers. The expansion drawers hold up to 60 drives each. With the new features of intermix, the following drives are supported:
7200 RPM SATA drives in 500, 750 and 1000 GB capacities
15K RPM SAS drives in 146, 300 and 450 GB capacities
The DCS9900 groups the drives into sets of 10, in RAID-6 ranks of 8+2P. IBM supports either 5, 10 or 20 expansion drawers to make a complete system. The maximum configuration would be 1200 drives of the 1000GB SATA drives, for a total of 1.2 PB in two frames. Each rank must be all the same type and capacity drive, but you can mix different types within the entire system.
The DCS9900 supports "Sleep Mode", an implementation of Massive Array of Idle Disks [MAID] technology, whereby each RAID rank can be either awake and spinning, or in energy-efficient standby mode. This makes for a more "green" storage system for data that is not accessed frequently.