Topic
  • 4 replies
  • Latest Post - ‏2013-08-07T13:31:10Z by HermannSW
jisspe
jisspe
5 Posts

Pinned topic Does IMS Connect in Datapower Supports commit mode 0 and 1 ?

‏2013-06-27T14:16:45Z |

Hi All,

I was doing a POC on IMS connect in Datapower XI50 , version 5.0.0.4.

The consumer will be SOAP/HTTP and the back end is mainframe IMS transactions.

We are being able to establish successful connectivity with back end and getting a proper cobol response from back end with out any issues.

In mainframe there will be two kinds of commit modes for any transaction such as commit mode 0 ( zero : commit-then-send response) and Commit mode 1 (one : send response- then commit ).

Can any of you please let me know that wether the  Datapower version 5.x is having support to both the commit modes 0 and 1  ??

If not which version of Datapower or patch will provide complete suppport ??

This information is required for me to complete the POC, kindly help ASAP.

Regards,

Jiss Peter,

jiss07@gmail.com

Updated on 2013-06-27T14:29:26Z at 2013-06-27T14:29:26Z by jisspe
  • HermannSW
    HermannSW
    5921 Posts
    ACCEPTED ANSWER

    Re: Does IMS Connect in Datapower Supports commit mode 0 and 1 ?

    ‏2013-06-27T15:47:50Z  

    It seems that commit modes are supported, from 5.0.0 InfoCenter:

    http://pic.dhe.ibm.com/infocenter/wsdatap/v5r0m0/index.jsp?topic=%2Fcom.ibm.dp.xi.doc%2Fmultiprotocolgatewaydevelopersguide.xi50276.htm

     

    1. In the Logical Terminal Name field, specify an override value. OTMA places this value in the IOPCB field. If you do not specify an override value, OTMA places the IMS Connect-defined TPIPE name in the IOPCB field. The TPIPE name is set to one of the following values based on the commit mode:
    • If the commit mode is 0, sets the value to the client identifier (CLIENT ID).
    • If the commit mode is 1, sets the value to the port identifier (PORT ID.

      If you use the LTERM value in the IOPCB to make logic decisions, be aware of the naming conventions of the IOPCB LTERM name.

     


    Hermann<myXsltBlog/> <myXsltTweets/> <myCE/>

     

  • HermannSW
    HermannSW
    5921 Posts

    Re: Does IMS Connect in Datapower Supports commit mode 0 and 1 ?

    ‏2013-06-27T15:47:50Z  

    It seems that commit modes are supported, from 5.0.0 InfoCenter:

    http://pic.dhe.ibm.com/infocenter/wsdatap/v5r0m0/index.jsp?topic=%2Fcom.ibm.dp.xi.doc%2Fmultiprotocolgatewaydevelopersguide.xi50276.htm

     

    1. In the Logical Terminal Name field, specify an override value. OTMA places this value in the IOPCB field. If you do not specify an override value, OTMA places the IMS Connect-defined TPIPE name in the IOPCB field. The TPIPE name is set to one of the following values based on the commit mode:
    • If the commit mode is 0, sets the value to the client identifier (CLIENT ID).
    • If the commit mode is 1, sets the value to the port identifier (PORT ID.

      If you use the LTERM value in the IOPCB to make logic decisions, be aware of the naming conventions of the IOPCB LTERM name.

     


    Hermann<myXsltBlog/> <myXsltTweets/> <myCE/>

     

  • jisspe
    jisspe
    5 Posts

    Re: Does IMS Connect in Datapower Supports commit mode 0 and 1 ?

    ‏2013-06-27T19:57:47Z  
    • HermannSW
    • ‏2013-06-27T15:47:50Z

    It seems that commit modes are supported, from 5.0.0 InfoCenter:

    http://pic.dhe.ibm.com/infocenter/wsdatap/v5r0m0/index.jsp?topic=%2Fcom.ibm.dp.xi.doc%2Fmultiprotocolgatewaydevelopersguide.xi50276.htm

     

    1. In the Logical Terminal Name field, specify an override value. OTMA places this value in the IOPCB field. If you do not specify an override value, OTMA places the IMS Connect-defined TPIPE name in the IOPCB field. The TPIPE name is set to one of the following values based on the commit mode:
    • If the commit mode is 0, sets the value to the client identifier (CLIENT ID).
    • If the commit mode is 1, sets the value to the port identifier (PORT ID.

      If you use the LTERM value in the IOPCB to make logic decisions, be aware of the naming conventions of the IOPCB LTERM name.

     


    Hermann<myXsltBlog/> <myXsltTweets/> <myCE/>

     

    Thanks alot Hermann..!!!

    This is really helpful information..

    Regards,

    Jiss Peter

  • Jaango
    Jaango
    267 Posts

    Re: Does IMS Connect in Datapower Supports commit mode 0 and 1 ?

    ‏2013-08-07T11:08:48Z  
    • jisspe
    • ‏2013-06-27T19:57:47Z

    Thanks alot Hermann..!!!

    This is really helpful information..

    Regards,

    Jiss Peter

    Hi this field, Logical Terminal Name, is even available in 4.x firmware. However the online help doesnt talk about commit modes. So is this really supported in 5.x firmware?


    What should we specify in this field, any sample values?

    From online help, seems like we have to set CLIENT ID for commit mode0 and PORT ID for commit mode1.

  • HermannSW
    HermannSW
    5921 Posts

    Re: Does IMS Connect in Datapower Supports commit mode 0 and 1 ?

    ‏2013-08-07T13:31:10Z  
    • Jaango
    • ‏2013-08-07T11:08:48Z

    Hi this field, Logical Terminal Name, is even available in 4.x firmware. However the online help doesnt talk about commit modes. So is this really supported in 5.x firmware?


    What should we specify in this field, any sample values?

    From online help, seems like we have to set CLIENT ID for commit mode0 and PORT ID for commit mode1.

    This 4.0.1 InfoCenter page talks on commit mode as above:

    http://publib.boulder.ibm.com/infocenter/wsdatap/4mt/index.jsp?topic=%2Fcom.ibm.dp.xi.doc%2Fwebserviceproxydevelopersguide.xi50294.htm

     

    Hermann<myXsltBlog/> <myXsltTweets/> <myCE/>