Topic
  • 3 replies
  • Latest Post - ‏2015-12-22T02:16:39Z by JayWang137
balusethuraman
balusethuraman
119 Posts

Pinned topic WCS 7 development environment setup

‏2012-10-11T04:36:48Z |
What are all the steps I need to do after installing RAD,WAS and wcs7 like configuring the workspace, publishing the store, configuring the DB.. Can anyone tell me the correct order that I have to do.. PLz help me.. Thanks in advance !!!
Updated on 2012-10-11T05:08:18Z at 2012-10-11T05:08:18Z by Raj.S
  • Raj.S
    Raj.S
    528 Posts

    Re: WCS 7 development environment setup

    ‏2012-10-11T05:01:09Z  
    The below link would help you.
    http://publib.boulder.ibm.com/infocenter/wchelp/v7r0m0/index.jsp?topic=%2Fcom.ibm.commerce.install.doc%2Ftasks%2Ftigdevroadmap.htm

    In short, here is the sequence to instal
    DB
    Installation Manager
    RAD + RAD Upgrade (if required)
    WAS + WAS fix pack
    WCS + WCS featurepack (do not enable any features) + fixpack
    Point to new DB and enable features.

    Regards,
    Raj
  • Raj.S
    Raj.S
    528 Posts

    Re: WCS 7 development environment setup

    ‏2012-10-11T05:08:18Z  
    • Raj.S
    • ‏2012-10-11T05:01:09Z
    The below link would help you.
    http://publib.boulder.ibm.com/infocenter/wchelp/v7r0m0/index.jsp?topic=%2Fcom.ibm.commerce.install.doc%2Ftasks%2Ftigdevroadmap.htm

    In short, here is the sequence to instal
    DB
    Installation Manager
    RAD + RAD Upgrade (if required)
    WAS + WAS fix pack
    WCS + WCS featurepack (do not enable any features) + fixpack
    Point to new DB and enable features.

    Regards,
    Raj
    Forgot to mention, this is the conventional way to do the installation. But to be safe, it is better if you have a minor change to the sequence. Reason being the fixpacks and featurepacks may come up with some changes to the datamodel, which would need you to run updatedb.bat

    DB
    Installation Manager
    RAD + RAD Upgrade (if required)
    WAS + WAS fix pack
    WCS Base (without any FP/FEP)
    Point to new DB
    WCS fixpack & featurepack
    You can choose the way you wish to.

    Regards,
    Raj
  • JayWang137
    JayWang137
    2 Posts

    Re: WCS 7 development environment setup

    ‏2015-12-22T02:16:39Z  
    • Raj.S
    • ‏2012-10-11T05:01:09Z
    The below link would help you.
    http://publib.boulder.ibm.com/infocenter/wchelp/v7r0m0/index.jsp?topic=%2Fcom.ibm.commerce.install.doc%2Ftasks%2Ftigdevroadmap.htm

    In short, here is the sequence to instal
    DB
    Installation Manager
    RAD + RAD Upgrade (if required)
    WAS + WAS fix pack
    WCS + WCS featurepack (do not enable any features) + fixpack
    Point to new DB and enable features.

    Regards,
    Raj

    I am new to WCS either. Understand there are many software need to be installed and configured. I wonder if there is a way to get a installed dev VM. So I can proctice.

    Or if there is an quick installation for all relevant software. The installer can install / config all for me.

    Many thanks,