Topic
  • 6 replies
  • Latest Post - ‏2012-07-26T13:42:37Z by RVXY_Shajeel_Khan
RVXY_Shajeel_Khan
RVXY_Shajeel_Khan
30 Posts

Pinned topic Trouble Connecting to z1090

‏2012-07-24T14:05:11Z |
Hi All,

I'm trying a new installation of RDz UT. After IPLing the system i am unable to connect to UT box through PCOMM (IBM Personal Communication). After giving IP and Port in PCOMM when i use to connect so it says;

"Local socket trying to connect to remote server/Host192.168.32.130 using port 3270 infinitely...."

Kindly help me out in the following error.
Thanks,
Shajeel Khan
Updated on 2012-07-26T13:42:37Z at 2012-07-26T13:42:37Z by RVXY_Shajeel_Khan
  • RDzJohn
    RDzJohn
    273 Posts

    Re: Trouble Connecting to z1090

    ‏2012-07-24T14:14:16Z  
    Check the IP address of your UT machine and ensure it is valid. Make sure that TCPIP starts cleanly with no errors on any of the interfaces. Connect PCOMM to the valid TCPIP address. If none of this makes any sense, read zPDT Redbook Vol 2 Chapter 3. Scenario 4 is the easiest to configure using a SA router/ bridge.

    RDzJohn
  • SystemAdmin
    SystemAdmin
    253 Posts

    Re: Trouble Connecting to z1090

    ‏2012-07-25T06:53:27Z  
    Shajeel,

    Check that TCP/IP is started, and try a ping from your workstation where you have PCOMM to the UT Box.
    If this is correct, then can you please configure the PCOMM emulator so that it points to port number 23 instead of port number 3270?
  • RVXY_Shajeel_Khan
    RVXY_Shajeel_Khan
    30 Posts

    Re: Trouble Connecting to z1090

    ‏2012-07-26T09:51:50Z  
    Hi Rafa,

    I had checked everything but still i am unable to connect.
    Thanks,
    Shajeel
  • JavaPoet
    JavaPoet
    12 Posts

    Re: Trouble Connecting to z1090

    ‏2012-07-26T11:39:44Z  
    Hi Rafa,

    I had checked everything but still i am unable to connect.
    Thanks,
    Shajeel
    Does the RDzUT start without errors? Also have you configured the firewall to accept connections on port 3270?
  • RVXY_Shajeel_Khan
    RVXY_Shajeel_Khan
    30 Posts

    Re: Trouble Connecting to z1090

    ‏2012-07-26T13:18:22Z  
    • JavaPoet
    • ‏2012-07-26T11:39:44Z
    Does the RDzUT start without errors? Also have you configured the firewall to accept connections on port 3270?
    JavaPoet,

    My firewall is already disable! Do you want to enable it and then configure it?
    Thanks,
    Shajeel
  • RVXY_Shajeel_Khan
    RVXY_Shajeel_Khan
    30 Posts

    Re: Trouble Connecting to z1090

    ‏2012-07-26T13:42:37Z  
    JavaPoet,

    My firewall is already disable! Do you want to enable it and then configure it?
    Thanks,
    Shajeel
    Hi All,

    Issue Resolved, port was closed. I used this command to open the port;

    "/sbin/iptables -A INPUT -m state --state NEW -m tcp -p tcp --dport 3270 -j ACCEPT"
    Thanks,
    Shajeel Ahmed Khan