Topic
2 replies Latest Post - ‏2013-06-26T21:11:09Z by Ahmar
Ahmar
Ahmar
10 Posts
ACCEPTED ANSWER

Pinned topic Sensor "CPU 2 Int Link" has transitioned to critical

‏2013-06-26T14:47:02Z |

Dear Team,

Kindly advice.

Sensor "CPU 2 Int Link"

Sensor "CPU 2 Int Link" has transitioned to critical from a less severe state

 

Chassis Event Log
LogName CreationTimeStamp EventID MessageID Message PerceivedSeverity AuxiliaryData
Chassis Event Log 06/22/2013 09:53:59 0x4000001400000000 IMM0020 The Chassis Event Log on system SN# 06R9870 cleared by user USERID Information  
Chassis Event Log 06/22/2013 09:54:30 0x4000000f00000000 IMM0015 Attempting to Power Off server SN# 06R9870 by user USERID Information  
Chassis Event Log 06/22/2013 09:54:33 0x806f00091381ffff PLAT0106 "Host Power" has been turned off Information  
Chassis Event Log 06/22/2013 09:55:58 0x4000000f00000000 IMM0015 Attempting to Power Up server SN# 06R9870 by user USERID Information  
Chassis Event Log 06/22/2013 09:56:03 0x816f00091381ffff PLAT0107 "Host Power" has been turned on Information  
Chassis Event Log 06/22/2013 10:05:56 0x4000000e00000000 IMM0014 Remote Login Successful. Login ID: USERID from Web at IP address 10.0.1.100 Information  
Chassis Event Log 06/22/2013 10:07:44 0x4000001900000000 IMM0025 LAN: Ethernet[eth1] interface is now active Information  
Chassis Event Log 06/22/2013 10:07:45 0x4000001700000000 IMM0023 ENET[sp-ethernetport] IP-Cfg:HstName=IMM-6CAE8B791FED, IP@=10.0.1.163 ,NetMsk=255.255.254.0, GW@=10.0.1.254 Information  
Chassis Event Log 06/22/2013 10:07:46 0x4000003700000000 IMM0055 ENET[sp-ethernetport] IPv6-LinkLocal:HstName=IMM-6CAE8B791FED, IP@=fe80::6eae:8bff:fe79:1fed, Pref=64 Information  
Chassis Event Log 06/22/2013 10:07:56 0x8007021b0303ffff PLAT0522 Sensor "CPU 3 Int Link" has transitioned to critical from a less severe state Major  
Chassis Event Log 06/22/2013 10:07:56 0x800301081381ffff PLAT0508 Sensor "AC RESTORE" has asserted Information  
Chassis Event Log 06/22/2013 10:07:59 0x8007021b0302ffff PLAT0522 Sensor "CPU 2 Int Link" has transitioned to critical from a less severe state Major  
Chassis Event Log 06/22/2013 10:11:43 0x4000002400000000 IMM0036 Flash of Unknown from Web failed for user USERID Degraded/Warning  
Chassis Event Log 06/22/2013 10:15:27 0x4000002400000000 IMM0036 Flash of Unknown from Web failed for user USERID Degraded/Warning  
Chassis Event Log 06/22/2013 10:15:54 0x806f00091381ffff PLAT0106 "Host Power" has been turned off Information  
Chassis Event Log 06/22/2013 10:15:59 0x816f00091381ffff PLAT0107 "Host Power" has been turned on Information  
Chassis Event Log 06/22/2013 10:40:28 0x800701211f04ffff PLAT0520 Sensor "Ext QPI Link 4" has transitioned from normal to non-critical state Degraded/Warning  
Chassis Event Log 06/22/2013 10:50:29 0x800b01081381ffff PLAT0802 Redundancy Lost for "Power Group 1" has asserted Major

 

  • DaveQ
    DaveQ
    110 Posts
    ACCEPTED ANSWER

    Re: Sensor "CPU 2 Int Link" has transitioned to critical

    ‏2013-06-26T19:27:54Z  in response to Ahmar

    Ahmar,

    You may need to file a support request for a replacement QPI Wrap Card. Certain cards contained a defect which leads to these errors. See the article referenced below for more information.

     "EXT QPI LINK" events and possible operating system hang - IBM System x3850 X5 (7143, 7191)

    http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=migr-5089038

     

    Dave

    • Ahmar
      Ahmar
      10 Posts
      ACCEPTED ANSWER

      Re: Sensor "CPU 2 Int Link" has transitioned to critical

      ‏2013-06-26T21:11:09Z  in response to DaveQ

      Thanks a ton Dave.