SAN Myths Uncovered: Quality of Service in Brocade FabricOS
seb_ 060000QVK2 Comments (11) Visits (27405)
When Brocade released FabricOS v6.0 in 2007 Quality of Service sounded like a great idea: It allows you to prioritize your traffic flow to the level of certain device pairs. There are 3 levels of priority:
High - Medium - Low
Inter Switch Links (ISLs) are logically partitioned into 8 so called Virtual Channels (VCs). Basically each of them has its own buffer management and the decision which virtual channel a frame should use is based on its destination address. If a particular end-to-end path is blocked or really slow, the impact on the communication over the other VCs is minimal. Thus only a subset of devices should be impaired during a bottleneck situation.
Quality of Service takes this one step further.
QoS-enabled ISLs consist of 16 VCs. There are slightly more buffers associated with a QoS ISL and these buffers are equally distributed over the data VCs. (There are some "reserved" VCs for fabric communication and special purposes). The amount of VCs makes the priority work - the most VCs (and therefore the most buffers) are dedicated to the high priority, the least for the low one. Medium lies in the middle obviously. So more important I/Os benefit from more resources than the not so important ones.
Sounds like a great idea!
Theoretically you can configure the traffic flow in terms of buffer credit assignment in your fabric very fine-grained. But that's in fact also the big crux: You have to configure it! That means you actually have to know which host's I/O to which target device should be which priority. Technically you create QoS-zones to categorize your connections. Low priority zones start with QOSL, high priority zones start with QOSH. Zones without such a prefix are considered as medium priority.
But how to categorize?
That's the tricky part. The company's departments relying on IT (virtually all) have to bring in their needs into the discussion. Maybe there are already different SLAs for different tiers of storage and an internal cost allocation in place. The I/O prioritization could go along with that and of course it has to be taken into account to effectively meet the pre-defined SLAs. If you have to start from the scratch, it's more a project for weeks and months than a simple configuration. And there is much psychology in it. Beside of that you really have to know how QoS works in details to design a prioritization concept. For example if you only have 20 high priority zones and 50 with medium priority but only 3 low priority zones, the low ones could even perform better. In the four years since its release I saw only a couple of customers really attempting to implement it.
In addition you need to buy the Adaptive Networking license!
So why should I care?
If QoS is such a niche feature, why blogging about it? Usually a port is configured for QoS when it comes from the factory. You can see it in the output of the command "portcfgshow". A new switch will have QoS in the state "AE" which means auto-enabled - in other words "on". An 8Gig ISL will be logically partitioned into the 16 VCs as described above and the buffer credits will be assigned to the high, the low and the medium priority VCs. But that does not mean that you can actually benefit from the feature, because you most probably have no QoS-zones! And so all your I/O share only the resources allocated for the medium priority. A huge part of the available buffers are reserved for VCs you cannot use! So as a matter of fact you end up with less buffers than without QoS and in many cases this made the difference between smooth running environments and immense performance degradation.
If you don't plan to design a detailed and well-balanced concept about the priorities in your SAN environments, I recommend to switch off QoS on the ports. I don't say QoS is bad! In fact with the Brocade HBA's possibility to integrate QoS even into the host connection - enabling different priorities for virtualized servers - you have the possibility to better cope with slow drain device behavior. But done wrong, QoS can have a very ugly impact on the SAN's performance!
Better know the features you use well - or they might turn against you...
As this was not clear enough in the text above and I got back a question about that, please be aware: Disabling QoS is disruptive for the link! In most FabricOS versions in combination with most switch models, the link will be taken offline and online again as soon as you disable it. In some combinations you'll get the message that it will turn effective with the next reset of the link. In that case you have to portdisable / portenable the port by yourself.
As this is a recoverable, temporary error your application most probably won't notice anything, but to be on the save side, you should do it in a controlled manner and - if really necessary in your environment - in times of little traffic or even a maintenance window. The command to disable it is:
portcfgqos --disable PORTNUMBER