- Cold Standby: The secondary node acts as backup of another identical primary system. It will be installed and configured only when the primary node breaks down for the first time. Subsequently, In the case of a failure in the primary the secondary node is powered on and the data restored before finally starting the failed component. Data from primary system can be backed up on a storage system and restored on secondary system as and when required. This generally provides a recovery time of a few hours.
- Warm Standby: The software component is installed and available on the secondary node. The secondary node is up and running. In the case of a failure on the primary node, these software components are started on the secondary node. This process is usually automated using a cluster manager.Data is regularly mirrored to secondary system using disk based replication or shared disk. This generally provides a recovery time of a few minutes.
- Hot Standby: Software components are installed and available on both primary and secondary nodes. The software components on the secondary system are up but will not process data or requests. Data is mirrored in near real time and both systems will have identical data. Data replication is typically done through the software’s capabilities. This generally provides a recovery time of a few seconds.
- Active-Active (Load Balanced): In this method both the primary and secondary systems are active and processing requests in parallel. Data replication happens through software capabilities and would be bi-directional. This generally provides a recovery time that is instantaneous.
Visibility, Control and Automation
RohitShetty 1200008RCP Identificações:  tivoli tsa hacmp maximo tnpm tpm ibm tbsm bsm db2 tsamp rohit smc shetty ha samp veritas 7.139 Visitas
Clustering is the most common technique to achieve High availability for any services by introducing redundancy in software, hardware and data. In a failure the clustering software immediately start the application on the standby system without requiring administrative intervention. Depending on the type of redundancy in software to be provided for High Availability, clusters can be configured in any of the following configurations:
RohitShetty 1200008RCP Identificações:  smc tsa veritas samp tsamp db2 tpm maximo shetty tbsm tivoli hacmp tnpm ha ibm bsm rohit 2.351 Visitas
Continuous Availability (CA)- Attribute of a system to deliver non disruptive service to the end user 7 days a week, 24 HOURS A DAY (there are no planned or unplanned outages).
Continuous Operations (CO)- Attribute of a system to continuously operate and mask PLANNED OUTAGES from end-users. It employs Non-disruptive hardware and software changes, non-disruptive configuration, software coexistence.
High Availability (HA)- The attribute of a system to provide service during defined periods, at acceptable or agreed upon levels and masks UNPLANNED OUTAGES from end-users. It employs Fault Tolerance; Automated Failure Detection, Recovery, Bypass Reconfiguration, Testing, Problem and Change Management.
RohitShetty 1200008RCP Identificações:  tsamp veritas ibm tsa ha tivoli tbsm bsm samp tnpm maximo shetty db2 tpm hacmp rohit smc 2.315 Visitas
Fault tolerance relies on specialized hardware to detect a hardware fault and instantaneously switch to a redundant hardware component whether the failed component is a processor, memory board, power supply, I/O subsystem, or storage subsystem. The fault tolerant model does not address software failures, by far the most common reason for downtime.
High availability views availability not as a series of replicated physical components, but rather as a set of system-wide, shared resources that cooperate to guarantee essential services. High availability combines software with industry-standard hardware to minimize downtime by quickly restoring essential services when a system, component, or application fails. While not instantaneous, services are restored rapidly, often in less than a minute.
The difference between fault tolerance and high availability is that a fault tolerant environment has no service interruption but a significantly higher cost, while a highly available environment has a minimal service interruption. Many sites are willing to absorb a small amount of downtime with high availability rather than pay the much higher cost of providing fault tolerance. Additionally, in most highly available configurations, the backup processors are available for use during normal operation. High availability systems are an excellent solution for applications that must be restored quickly and can withstand a short interruption should a failure occur. A few industries have time-critical applications and cannot withstand even a few seconds of downtime. However, many other industries can withstand small periods of time when their database is unavailable. For those industries, SAMP can provide the necessary continuity of service without total redundancy.
RohitShetty 1200008RCP Identificações:  maximo veritas rohit shetty tpm bsm ibm smc tsamp ha tivoli hacmp samp tnpm db2 tsa tbsm 2.148 Visitas
People are generally confused about the level of redundancy they need to provide while designing a HA solution. The cardinality of the primary to secondary components can be described in the following way and this decides the deployment topology of the various components:
RohitShetty 1200008RCP Identificações:  tbsm rohit smc ibm bsm maximo veritas tnpm tsamp db2 tpm tivoli hacmp ha tsa shetty samp 1 Comentário 2.126 Visitas
On demand businesses require high availability and SAMP (Tivoli System Automation for Multi platforms) addresses pain points such as:
SAMP overcomes these problems through policy-based automation that supports grouping of resources and relationships. SAMP can do this in environments where applications run on diverse platforms. SAMP helps you to remain competitive, flexible, and responsive to operate in a cost effective manner.
SAMP provides high availability and policy-based automation for applications and services across heterogeneous environments. It ensures continuous high availability and reduces frequency and duration of service disruptions for critical applications and middle ware running on heterogeneous platforms and virtualization technologies.
Tivoli System Automation for Multi platforms is a high-availability cluster solution that provides several monitoring mechanisms to detect system failures and a set of rules to initiate the correct action without any user intervention. The set of rules is called a policy, This policy describes the relationships between applications or resources. This provides System Automation for Multi platforms with extensive up-to-date information about the system landscape so that it can restart the resource on the current node or move the whole application to another cluster node.