This blog is for the open exchange of ideas relating to IBM Systems, storage and storage networking hardware, software and services.
(Short URL for this blog: ibm.co/Pearson )
Tony Pearson is a Master Inventor, Senior IT Architect and Event Content Manager for [IBM Systems for IBM Systems Technical University] events. With over 30 years with IBM Systems, Tony is frequent traveler, speaking to clients at events throughout the world.
Lloyd Dean is an IBM Senior Certified Executive IT Architect in Infrastructure Architecture. Lloyd has held numerous senior technical roles at IBM during his 19 plus years at IBM. Lloyd most recently has been leading efforts across the Communication/CSI Market as a senior Storage Solution Architect/CTS covering the Kansas City territory. In prior years Lloyd supported the industry accounts as a Storage Solution architect and prior to that as a Storage Software Solutions specialist during his time in the ATS organization.
Lloyd currently supports North America storage sales teams in his Storage Software Solution Architecture SME role in the Washington Systems Center team. His current focus is with IBM Cloud Private and he will be delivering and supporting sessions at Think2019, and Storage Technical University on the Value of IBM storage in this high value IBM solution a part of the IBM Cloud strategy. Lloyd maintains a Subject Matter Expert status across the IBM Spectrum Storage Software solutions. You can follow Lloyd on Twitter @ldean0558 and LinkedIn Lloyd Dean.
Tony Pearson's books are available on Lulu.com! Order your copies today!
Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Continuing my series on a [Laptop for Grandma], I thought I would pursue some of the "low-RAM" operating system choices. Grandma's Thinkpad R31 has only 384MB of RAM.
All of the ones below are based on Linux. For those who aren't familiar with installing or running the Linux operating system, here are some helpful tips:
Most Linux distributors allow you to download an ISO file for free. These can be either (a) burned to a CD, (b) burned to a DVD, or (c) written to a USB memory stick.
The ISO can be either a "LiveCD/LiveDVD" version, an installation program, or a combination of the two. The "Live" version allows you to boot up and try out the operating system without modifying the contents of your hard drive. Windows and Mac OS users can try out Linux without impact to their existing environment. Some Linux distributions offer both a full LiveCD+Installer version, as well as an alternate text-based Installer-only version. The latter often requires less RAM to use.
When installing, it is best to have the laptop plugged in to an electrical outlet, and hard-wired to the internet in case it needs to download the latest drivers for your particular hardware.
A CD can hold only 700MB. Many of the newer Linux distributions exceed that, requiring a DVD or USB stick instead. If your laptop has an older optical drive, it may not be able to read DVD media. Some older optical drives can only read CD's, not burn them. In my case, I burned the CDs on another machine, and then used them on grandma's Thinkpad R31.
To avoid burning "a set of coasters" when trying out multiple choices, consider using rewriteable optical media, or the USB option. If you don't like it, you can re-use for something else.
The program [Unetbootin] can take most ISO files and write them to a bootable USB stick. On my Red Hat Enterprise Linux 6 laptop, I had to also install p7zip and p7zip-plugins first.
The BIOS on some older machines, like my grandma's Thinkpad R31, cannot boot from USB. The [PLoP Boot Manager] allows you to first boot from floppy or CD-ROM, and then allows you to boot from the USB. This worked great on my grandma's system. The PLoP Boot Manager is also available on the [Ultimate Boot CD].
While I am a big fan of SUSE, Red Hat, and Ubuntu, these all require more RAM than available on grandma's laptop. Here are some Low-RAM alternatives I tried:
Damn Small Linux 4.11 RC2
The Damn Small Linux [DSL] project was dormant since 2008, but has a fresh new release for 2012. This baby can run in as little 16MB or RAM! If you have 128MB of RAM or more, the OS can run entirely from RAM, providing much faster performance.
Of course, there are always trade-offs, and in this case, apps were chosen for their size and memory footprint, not necessarily for their user-friendliness and eye candy. For example, the xMMS plays MP3 music, but I did not find it as friendly as iTunes or Rhythmbox.
Boot time is fast. From hitting the power-on button to playing the first note of MP3 music was about 1 minute.
Installing DSL Linux on the hard drive converts it into a Debian distribution, which then allows more options for applications.
Next up was [MacPup]. The latest version is 529, based on Pupply Linux 5.2.60 Precise, compatible with Ubuntu 12.04 Precise Pangolin. While traditional Puppy Linux clutters the screen with apps, the MacPup tries to have the look-and-feel of the MacOS by having a launcher tray at the bottom center of the screen.
Both MacPup and Puppy Linux can run in very small amounts of RAM and disk space. Like DSL above, you can opt to run MacPup entirely in 128MB of RAM. Unfortunately, the trade-off is a lack of application choices.
Installation to the hard drive was quite involved, certainly not for the beginner. First, you have to use Gparted to partition the disk. I created a 19GB (sda1) for my files, and 700MB (sda5) for swap. I had troubles with "ext4" file system, so re-formatted to "ext3". Second, you have to copy the files over from the LiveCD using the "Puppy Universal Installer". Third, you have to set up the Bootloader. Grub didn't work, so I installed Grub4Dos instead.
The music app is called "Alsa Player", and I was able to drag the icon into the startup tray. time-to-first-note was just over 1 minute. Fast, but not as "simple-to-use" as I would like.
SliTaz 4.0 claims to be able to run in as little as 48MB of RAM and 100MB of disk space. Time-to-first-note was similar to MacPup, but I didn't care for the TazPanel for setup, and the TazPkg for installing a limited set of software packages. I could not get Wi-Fi working at all on SliTaz, and just gave up trying.
All three of these ran on grandma's Thinkpad R31, and all three could play MP3 music. However, I was concerned that they were not as simple to use as grandma would like, and I would be concerned the amount of time and effort I might have to spend if things go wrong.
Are you tired of hearing about Cloud Computing without having any hands-on experience? Here's your chance. IBM has recently launched its IBM Development and Test Cloud beta. This gives you a "sandbox" to play in. Here's a few steps to get started:
Generate a "key pair". There are two keys. A "public" key that will reside in the cloud, and a "private" key that you download to your personal computer. Don't lose this key.
Request an IP address. This step is optional, but I went ahead and got a static IP, so I don't have to type in long hostnames like "vm353.developer.ihost.com".
Request storage space. Again, this step is optional, but you can request a 50GB, 100GB and 200GB LUN. I picked a 200GB LUN. Note that each instance comes with some 10 to 30GB storage already. The advantage to a storage LUN is that it is persistent, and you can mount it to different instances.
Start an "instance". An "instance" is a virtual machine, pre-installed with whatever software you chose from the "asset catalog". These are Linux images running under Red Hat Enterprise Virtualization (RHEV) which is based on Linux's kernel virtual machine (KVM). When you start an instance, you get to decide its size (small, medium, or large), whether to use your static IP address, and where to mount your storage LUN. On the examples below, I had each instance with a static IP and mounted the storage LUN to /media/storage subdirectory. The process takes a few minutes.
So, now that you are ready to go, what instance should you pick from the catalog? Here are three examples to get you started:
IBM WebSphere sMASH Application Builder
Base OS server to run LAMP stack
Next, I decided to try out one of the base OS images. There are a lot of books on Linux, Apache, MySQL and PHP (LAMP) which represents nearly 70 percent of the web sites on the internet. This instance let's you install all the software from scratch. Between Red Hat and Novell SUSE distributions of Linux, Red Hat is focused on being the Hypervisor of choice, and SUSE is focusing on being the Guest OS of choice. Most of the images on the "asset catalog" are based on SLES 10 SP2. However, there was a base OS image of Red Hat Enterprise Linux (RHEL) 5.4, so I chose that.
To install software, you either have to find the appropriate RPM package, or download a tarball and compile from source. To try both methods out, I downloaded tarballs of Apache Web Server and PHP, and got the RPM packages for MySQL. If you just want to learn SQL, there are instances on the asset catalog with DB2 and DB2 Express-C already pre-installed. However, if you are already an expert in MySQL, or are following a tutorial or examples based on MySQL from a classroom textbook, or just want a development and test environment that matches what your company uses in production, then by all means install MySQL.
This is where my SSH client comes in handy. I am able to login to my instance and use "wget" to fetch the appropriate files. An alternative is to use "SCP" (also part of PuTTY) to do a secure copy from your personal computer up to the instance. You will need to do everything via command line interface, including editing files, so I found this [VI cheat sheet] useful. I copied all of the tarballs and RPMs on my storage LUN ( /media/storage ) so as not to have to download them again.
Compiling and configuring them is a different matter. By default, you login as an end user, "idcuser" (which stands for IBM Developer Cloud user). However, sometimes you need "root" level access. Use "sudo bash" to get into root level mode, and this allows you to put the files where they need to be. If you haven't done a configure/make/make install in awhile, here's your chance to relive those "glory days".
In the end, I was able to confirm that Apache, MySQL and PHP were all running correctly. I wrote a simple index.php that invoked phpinfo() to show all the settings were set correctly. I rebooted the instance to ensure that all of the services started at boot time.
Rational Application Developer over VDI
This last example, I started an instance pre-installed with Rational Application Developer (RAD), which is a full Integrated Development Environment (IDE) for Java and J2EE applications. I used the "NX Client" to launch a virtual desktop image (VDI) which in this case was Gnome on SLES 10 SP2. You might want to increase the screen resolution on your personal computer so that the VDI does not take up the entire screen.
From this VDI, you can launch any of the programs, just as if it were your own personal computer. Launch RAD, and you get the familiar environment. I created a short Java program and launched it on the internal WebSphere Application Server test image to confirm it was working correctly.
If you are thinking, "This is too good to be true!" there is a small catch. The instances are only up and running for 7 days. After that, they go away, and you have to start up another one. This includes any files you had on the local disk drive. You have a few options to save your work:
Copy the files you want to save to your storage LUN. This storage LUN appears persistent, and continues to exist after the instance goes away.
Take an "image" of your "instance", a function provided in the IBM Developer and Test Cloud. If you start a project Monday morning, work on it all week, then on Friday afternoon, take an "image". This will shutdown your instance, and backup all of the files to your own personal "asset catalog" so that the next time you request an instance, you can chose that "image" as the starting point.
Another option is to request an "extension" which gives you another 7 days for that instance. You can request up to five unique instances running at the same time, so if you wanted to develop and test a multi-host application, perhaps one host that acts as the front-end web server, another host that does some kind of processing, and a third host that manages the database, this is all possible. As far as I can tell, you can do all the above from either a Windows, Mac or Linux personal computer.
Getting hands-on access to Cloud Computing really helps to understand this technology!