Tony Pearson is a Master Inventor and Senior IT Architect for the IBM Storage product line at the
IBM Systems Client Experience Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services.
(Short URL for this blog: ibm.co/Pearson )
My books are available on Lulu.com! Order your copies today!
Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Yesterday, I promised I would cover other products from the Feb 12 announcement. Today I will focus on the IBM SAN768B director. Some people are confused on the differences between switchesand directors. I find there are three key differences:
Directors are designed to be 24x7 operation, highly available with no single points of failure or repair. Generally, all components in directors are redundant and hot-swappable, including Control Processors. In switches, some components are redundant and hot-swappable, such as fans and power supplies), but not the “motherboard” or controller. Often you have to take down a switch to make firmware or major hardware changes or upgrades.
Directors are designed to take in "blades" with different features, port counts, or protocol capabilities. You can add or remove blades while the system is up and running. Switches have a fixed number of ports. (A Small Form-factor Pluggable optical transceiver [SFP] is the component that turns electric pulses into light pulses (and visa versa). You plug the SFP into the switch, and then the fiber optic cable is plugged into the SFP).
With switches, you often start with a base number of active ports, and then can enable the rest of the ports as you need them.
Directors have hundreds of ports. Switches tend to have 64 ports or less.
Last year, Brocade acquired McDATA. Both were OEMs for IBM, and IBM distinguished that in the naming convention. The IBM SAN***B name was used to denote products manufactured for IBM by Brocade, and a SAN***M name was used to denote products manufactured by McDATA.
At that time, Brocade and McDATA equipment did not mix very well on the same fabric, so IBM retained the naming convention so that you as a customer knew what it worked with.
Brocade now has released with new levels of both operating systems--Brocade's FOS and McDATA's EOS--and their respective fabric managers--Brocade Fabric Manager (FM) and McDATA's Enterprise Fabric Connectivity Manager (EFCM)--so that they have full interoperability.
Brocade's goal is to enhance EFCM to be a common software management platform for all of their products going forward.
IBM used the maximum port count in the name to provide some clue as to the size of the switch or director. The SAN16B-2 or the SAN32B-3 are switches that have a maximum of 16 and 32 ports. The SAN256B supports a maximumeight blades of your choosing.Two different types were supported for FC ports, a 16-port blade and a 32-port blade.If all eight were 32-port blades then the maximum was 256 ports, hence the name. But then Brocade began offering 48-port blades. Should IBM change the name? No, it decided to leave itthe SAN256B even though it can now have a maximum of 384 ports.
Not to confuse anyone, the SAN768B also has a maximum of 384 ports, in the same 14U dimensions, but with a special twist. Normally to connect two directors together you use up ports from each, in what are called "inter-switch links" (ISL).These are ports you are taking away from availability from the servers and storage controllers. The SAN768Boffers a new alternative called "inter-chassis links". Each SAN768B has two processing blades, and each has two ICL ports, so with just four two-meter (2m) cables, you get the equivalent of 128 FC 8 Gbps ISL links without using 128 individual ports on each side. That is like giving you 256 ports back for use with servers and storage!
Since IBM directors require 240 volt power, IBM TotalStorage SAN Cabinet C36 include power distribution units (PDUs). PDUs are just glorified power strips, but a new intelligent PDU (iPDU) option introduces additional intelligence to monitor energy consumption for customers looking to measure, and perhaps charge back, energy consumption to the rest of the business. You can stack two SAN768B in one cabinet, one on top of the other, and connected via ICLs, it wouldlook like one huge 768-port backbone.
As a backbone for your data center, the SAN768B is positioned for two emerging technologies:
8 Gbps Fibre Channel (FC)
The SAN768B is powerful enough to have 32-port blades run full speed on all ports off-blade without oversubscription. Oversubscription is an emotional topic.
Normally, blades (like switches) can handle all traffic at full speed without delays provided the in-bound and out-bound ports involved are all on the same blade. In a director, however, if you need to communicate from a port on one blade to a port on a different blade, it is possible that off-blade traffic might be constrained or delayed in its transit across the backplane.
On the SAN768B, both the 16-port and 32-port blades can run at full 8 Gbps speed, and the 48-port is exposed to oversubscription only if you have more than 32-ports running at full 8 Gbps transferring data off-blade concurrently.
The new 8 Gbps SFPs support auto-negotiation at N-1 and N-2 generation link speeds. This means that they will automatically slow down when communicating with 4Gpbs and 2 Gbps devices, but they cannot communicate with 1 Gbps devices. If you are still using 1 Gbps devices in your data center, you will need to use 4 Gbps SFPs (which also support 2 Gbps and 1 Gbps link speeds) to communicate with those older devices.
Basically, this new technology enables transport of Fibre Channel packets over 10 Gbps Ethernet links. This 10 Gbps Ethernet can also be used to carry traditional iSCSI and TCP/IP traffic. FCoE introduces new extensions to provide Fibre Channel characteristics, like being lossless, and offering consistent performance. The ANSI T11 team is driving FCoE as an open standard, and at the moment it is not fully baked. I suggest you don't buy any FCoE equipment prematurely, as pre-standard devices or host bus adapters could get you burned later when the standard is finalized.
The idea is that FCoE blades can be installed in a SAN768B along with traditional FC blades, allowing routing of traffic between traditional FC and new FCoE ports. Those who have invested in FCIP for long distance replication will be able to continue using either FC or FCoE inputs.
One of the big drivers of FCoE is IBM BladeCenter. Currently, most BladeCenter blades support both Ethernet and FC connectivity and are connected to both Ethernet and FC switches on the back of each BladeCenter chassis. With FCoE, we have the potential to run both FC and IP traffic across simpler all-Ethernet blades, connecting through all-Ethernet switches on the backs of each chassis.
For more information on the IBM SAN768B, see the [IBM Press Release]. For more detailson Brocade's strategy, here is an 8-page white paper on their[Data Center Fabric] vision.
Well, today's Tuesday, and you know what that means... IBM Announcements!
This week, IBM has their huge 3Q Launch. This on top of the [2Q results] IBM released yesterday. You can read how the rest of the company did, but it is good to see that IBM grew in both revenue and market share for storage!
As with any IBM launch of this magnitude, there are so many enhancements, I will spread them across several posts.
IBM System Storage TS7610 ProtecTIER® Deduplication Appliance Express
The TS7610 is a smaller appliance than the TS7650 we introduced last year, taking up only 3U of rack space (2U for the disk itself, and a 1U slide rail to simplify maintenance). This is designed for smaller deployments, such as midsized businesses between 100 and 1000 employees that backup 3TB of data per week or less. The unit relies on RAID protected SATA drives. Thanks to the same ProtecTIER data deduplication we have on the TS7650, the TS7610 can hold up to 135TB of backup data on just 5.4TB of disk capacity, with in-line data ingest at 80 MB/sec performance. This little Virtual Tape Library (VTL) emulates up to four TS3500 libraries, with 64 LTO-3 drives and over 8000 virtual tapes. See the [Announcement letter] for details.
The [ProtecTIER Entry Edition] offers a hub-and-spoke approach to replication. You can have up to twelve(12) TS7610 boxes (the "spokes") replicate to a central VTL (the "hub"). This can be ideal for protecting remote office or branch office deployments.
IBM dobules the storage capacity by utilizing 2TB hard disk drives for the N3300 and N3400 series models, maximizes customer satisfaction through Partner Select Bundles (software bundles) for all of the N3000 series (N3300, N3400, N3600), and offers Application and Server Packs (software bundles) for N3400 models.
For the high-end, IBM introduces an enhanced Performance Acceleration Module (PAM II) bundle for N7900 Gateway. This bundle includes two 512GB Solid State Drive PAM II adapters, two dual-port 10GbE TOE network interface cards (NIC), and various software features.
The DS5020 and EXP520 joins their bigger siblings DS5100 and DS5300 in supporting Solid State Drives (SSD), available in 73GB and 300GB capacities. A new air filter bezel is also available for these when used in dusty environments. See the [Announcement letter] for details.
For my friends down in Brazil, A new 2.8 meter length power cord that supports 220-250 volts is now available for all DS4000 and DS5000 series disk systems. Obrigado para o seu negócio!
IBM Tivoli Storage FlashCopy Manager v2.2
I covered this latest release in my post [FlashCopy Manager v2.2] but the marketing team felt we should include it with this launch to get added exposure and visibility.
I'll try to get to the rest in separate posts over the rest of this week.
IBM wins lots of awards, but this time is unique: [IBM and Fox Networks Group have jointly won an Engineering Emmy® Award] for Innovation from the Academy of Television Arts & Sciences. According to the Academy, by improving the ability of media companies to capture, manage and exploit content in digital form, IBM and Fox have fundamentally changed the way that audio and video content is managed and stored. Here's an excerpt from the IBM Press Release:
"By standardizing technologies in this way, Fox can now use open-standard, file-based tape in all aspects of production, post-production and distribution functions – displacing costly proprietary tape formats and/or disk subsystems. This provides media companies with the consumer equivalent of having their entire library of DVDs online and available at any time, and the ability to go to a specific scene, in any one of the movies, in an instant.
In the early stage of the technology initiative, the IBM/Fox team applied IBM-patented technologies invented by IBM Research for high-speed data movement. They also integrated traditional broadcast transport and encoding standards with IT industry open standards. This allowed either Standard Definition (SD) or HD programming to be available in real time for digital recording and repurposing -- with improved economics."
Unfortunately, people didn't like the name, but they loved the acronym, so it was renamed to Linear Tape File System. IBM offers LTFS single-drive edition on its LTO-5 and TS1140 tape drives, and LTFS library-edition across all of its tape libraries. Since everyone hates proprietary vendor lock-in, IBM has graciously shared LTFS as an open source standard with the rest of the Linear Tape Open consortium.
(Note: I was not there at the awards ceremony. The pictures were taken by Ed Childers, David Pease and Rainer Richter of each other. Additional photos are available on this [Flicr photo album].)
(1) Rainer Richter, Media Technology Market Partners LLC [MTMP], presenting the Emmy to Steve Canepa, IBM General Manager for Media and Entertainment industry. MTMP is an IBM Business Partner that offers integrated solutions for LTO and LTFS, consulting, services, and technology to the media and entertainment industry…
(2) Ed Childers, IBM manager of the Tape Drive Development team, holding the Emmy. Fellow IBM blogger Steve Hamm credits Ed on coming up with the idea for LTFS seven years ago, in his blog post [Coding and Loading in Las Vegas: How a Team of IBM Researchers Helped Transform the Way Video is Stored]. Ed wanted to make tape storage easier to use and to integrate it into the workflow of networks and studios, and suggested using an indexing system that would allow people to write software that would make video more accessible.
(3) David Pease, IBM Senior Technical Staff Member from the IBM Almaden Research Center, holding the Emmy. Along with Lucas Villa Real (IBM Brazil) and Michael Richmond (IBM Almaden), David and his team were able to come up with a working prototype in just four months. Michael discusses this in his posts [Tape? Does anyone care about Tape anymore?"] and [the Emmy goes to... LTFS].
Of course, Technology is only worthwhile if you put it to use. Our friends at FOX initially partnered with IBM to develop this video archive solution for the National Football League (NFL). If there is one place that "re-purposes" a lot of video footage, it is sports television. The technology proved so useful that FOX has since expanded it to other types of programming.
Intelligent block-level disk array that virtualizes both internal and external disk storage
8 Gbps FCP and 1GbE iSCSI
IBM Storwize V7000 disk system
Real-time compression appliance for files
10GbE/1GbE CIFS and NFS
Storwize, now an IBM company
IBM Real-time Compression STN-6800 appliance
1GbE CIFS and NFS
IBM Real-time Compression STN-6500 appliance
If you think this is the first time a company like IBM has pulled shenanigans with product names like this, think again. Here are a few posts that might refresh your memory:
In my September 2006 post, [A brand by any other name...] I explain that I started blogging specifically to promote the new "IBM System Storage" product line name, part of the "IBM Systems" brand resulting from merging the "eServer" and "TotalStorage' brands.
In my January 2007 post, [When Names Change], I explain our naming convention for our disk products, including our DS family, SAN Volume Controller and N series.
In my February 2008 post, [Getting Off the Island], I cover how the x/p/i/z designations came about for our various IBM server product lines.
But what about acquisitions? When [IBM acquired Lotus Development Corporation], it kept the "Lotus" brand. New products that fit the "collaboration" function were put under the Lotus brand. I think most people can accept this approach.
But have we ever seen an existing product renamed to an acquired name?
In my post January 2009 post
[Congratulations to Ken on your QCC Milestone], I mentioned that my colleague Ken Hannigan worked on an internal project initially called "Workstation Data Save Facility" (WDSF) which was changed to "Data Facility Distributed Storage Manager" (DFDSM), then renamed to "ADSTAR Distributed Storage Manager" (ADSM), and finally renamed to the name it has today: IBM Tivoli Storage Manager (TSM).
Readers reminded me that [IBM acquired Tivoli Systems, Inc.] in 1996, so TSM could not have been an internally developed product. Ha! Wrong! Let's take a quick history lesson on how this came about:
In the late 1980s, IBM Almaden research had developed a project to backup personal computers and workstations, which they called "Workstation Data Save Facility" or WDSF.
This was turned over to our development team, which immediately discarded the code, and wrote from scratch its replacmeent, called Data Facility Distributed Storage Manager (DFDSM), named similar to the Data Facility products on the mainframe (DFP, DFHSM, DFDSS). As a member of the Data Facility family, DFDSM didn't really fit. The rest processed mainframe data sets, but DFDSM processed Windows and UNIX files. That a version of DFDSM server was available to run on the mainframe was the only connection.
Then, in the early 1990s, there were discussions of possibly splitting IBM into a bunch of smaller "Baby Blues", similar to how [AT&T was split into "Baby Bells"], and how Forbes and Goldman Sachs now want to split Microsoft into [Baby Bills]. IBM considered naming the storage spin-off as ADSTAR, which stood for "Advanced Storage and Retrieval."
Pre-emptively, IBM renamed DFDSM to "ADSTAR Distributed Storage Manager" or ADSM.
Fortunately, in 1993, IBM brought a new sheriff to town, Lou Gerstner, who quickly squashed any plans to split up IBM. He quickly realized that IBM's core strength was building integrated stacks, combining systems, software and services to solve business problems.
In 1996, IBM acquired Tivoli Systems, Inc. to expand its "Systems Management" portfolio, and renamed ADSM over to IBM Tivoli Storage Manager, since "storage management" is an essential part of "systems management". Later, IBM TotalStorage Productivity Center would be renamed to "IBM Tivoli Storage Productivity Center."
I participated in five months of painful meetings to figure out what to name our new internally-developed midrange disk system. Since it ran SAN Volume Controller software, I pushed for keeping the SVC designation somehow. We considered DS naming convention, but the new midrange product would not fit between our existing DS5000 and DS6000 numbering scheme. A marketing agency we hired came up with nonsensical names, in the spirit of product names like Celerra, Centera and CLARiiON, using name generators like [Wordoid]. Luckily, in the nick of time, IBM acquired Storwize for its compression technology, and decided that Storwize as a name was way better fit than any of the names we came up with already.
However, the new IBM Storwize V7000 midrange product had nothing in common with the appliances acquired from Storwize, the company, so to avoid confusion, the latter products were renamed to [IBM Real-time Compression]. Fellow blogger Steven Kenniston, the Storage Alchemist from Storwize fame now part of IBM from the acquisition, gives his perspective on this in his post [Storwize – What is in a Name, Really?]. While I am often critical of the names and terms IBM uses, I have to say this last set of naming decisions makes a lot of sense to me and I support it wholeheartedly.
Well, it's Wednesday, and you know what that means... IBM Announcements!
(Actually most IBM announcements are on Tuesdays, but IBM gave me extra time to recover from my trip to Europe!)
Today, IBM announced [IBM PureSystems], a new family of expert-integrated systems that combine storage, servers, networking, and software, based on IBM's decades of experience in the IT industry. You can register for the [Launch Event] today (April 11) at 2pm EDT, and download the companion "Integrated Expertise" event app for Apple, Android or Blackberry smartphones.
(If you are thinking, "Hey, wait a minute, hasn't this been done before?" you are not alone. Yes, IBM introduced the System/360 back in 1964, and the AS/400 back in 1988, so today's announcement is on scheduled for this 24-year cycle. Based on IBM's past success in this area, others have followed, most recently, Oracle, HP and Cisco.)
Initially, there are two offerings:
IBM PureFlex™ System
IBM PureFlex is like IaaS-in-a-box, allowing you to manage the system as a pool of virtual resources. It can be used for private cloud deployments, hybrid cloud deployments, or by service providers to offer public cloud solutions. IBM drinks its own champagne, and will have no problem integrating these into its [IBM SmartCloud] offerings.
To simplify ordering, the IBM PureFlex comes in three tee-shirt sizes: Express, Standard and Enterprise.
IBM PureFlex is based on a 10U-high, 19-inch wide, standard rack-mountable chassis that holds 14 bays, organized in a 7 by 2 matrix. Unlike BladeCenter where blades are inserted vertically, the IBM PureFlex nodes are horizontal. Some of the nodes take up a single bay (half-wide), but a few are full-wide, take up two bays, the full 19-inch width of the chassis. Compute and storage snap in the front, while power supplies, fans, and networking snap in the back. You can fit up to four chassis in a standard 42U rack.
Unlike competitive offerings, IBM does not limit you to x86 architectures. Both x86 and POWER-based compute nodes can be mixed into a single chassis. Out of the box, the IBM PureFlex supports four operating systems (AIX, IBM i, Linux and Windows), four server hypervisors (Hyper-V, Linux KVM, PowerVM, and VMware), and two storage hypervisors (SAN Volume Controller and Storwize V7000).
There are a variety of storage options for this. IBM will offer SSD and HDD inside the compute nodes themselves, direct-attached storage nodes, and an integrated version of the Storwize V7000 disk system. Of course, every IBM System Storage product is supported as external storage. Since Storwize V7000 and SAN Volume Controller support external virtualization, many non-IBM devices will be supported automatically as well.
Networking is also optimized, with options for 10Gb and 40Gb Ethernet/FCoE, 40Gb and 56Gb Infiniband, 8Gbps and 16Gbps Fibre Channel. Much of the networking traffic can be handled within the chassis, to minimize traffic on external switches and directors.
For management, IBM offers the Flex System Manager, that allows you to manage all the resources from a single pane of glass. The goal is to greatly simplify the IT lifecycle experience of procurement, installation, deployment and maintenance.
IBM PureApplication™ System
IBM PureApplication is like PaaS-in-a-box. Based on the IBM PureFlex infrastructure, the IBM PureApplication adds additional software layers focused on transactional web, business logic, and database workloads. Initially, it will offer two platforms: Linux platform based on x86 processors, Linux KVM and Red Hat Enterprise Linux (RHEL); and a UNIX platform based on POWER7 processors, PowerVM and AIX operating system. It will be offered in four tee-shirt sizes (small, medium, large and extra large).
In addition to having IBM's middleware like DB2 and WebSphere optimized for this platform, over 600 companies will announce this week that they will support and participate in the IBM PureSystems ecosystem as well. Already, there are 150 "Patterns of Expertise" ready to deploy from IBM PureSystem Centre, a kind of a "data center app store", borrowing an idea used today with smartphones.
By packaging applications in this manner, workloads can easily shift between private, hybrid and public clouds.
If you are unhappy with the inflexibility of your VCE Vblock, HP Integrity, or Oracle ExaLogic, talk to your local IBM Business Partner or Sales Representative. We might be able to buy your boat anchor off your hands, as part of an IBM PureSystems sale, with an attractive IBM Global Financing plan.
Continuing this week's coverage of IBM's 3Q announcements, today it's all about storage for our mainframe clients.
IBM System Storage DS8700
IBM is the leader in high-end disk attached to mainframes, with the IBM DS8700 being our latest model in a long series of successful products in this space. Here are some key features:
Full Disk Encryption (FDE), which I mentioned in my post [Different Meanings of the word "Protect"]. FDE are special 15K RPM Fibre Channel drives that include their own encryption chip, so that IBM DS8700 can encrypt the data at rest without impacting performance of reads or writes. The encryption keys are managed by IBM Tivoli Key Lifecycle Manager (TKLM).
Easy Tier, which I covered in my post [DS8700 Easy Tier Sub Lun Automatic Migration] which offers what EMC promised but has yet to deliver, the ability to have CKD volumes and FBA LUNs to straddle the fence between Solid State Drives (SSD) and spinning disk. For example, a 54GB CKD volume could have 4GB on SSD and the remaining 50GB on spinning drives. The hottest extents are moved automatically to SSD, and the coldest moved down to spinning disk. To learn more about Easy Tier, watch my [7-minute video] on IBM [Virtual Briefing Center].
z/OS Distributed Data Backup (zDDB), announced this week, provides the ability for a program running on z/OS to backup data written by distributed operating systems like Windows or UNIX stored in FBA format. In the past, to backup FBA LUNs involved a program like IBM Tivoli Storage Manager client to read the data natively, send it over Ethernet LAN to a TSM Server, which could run on the mainframe and use mainframe resources. This feature eliminates the Ethernet traffic by allowing a z/OS program to read the FBA blocks through standard FICON channels, which can then be written to z/OS disk or tape resources. Here is the [Announcement Letter] for more details.
One program that takes advantage of this new zDDB feature already is Innovation's [FDRSOS], which I pronounce "fudder sauce". If you are an existing FDRSOS customer, now is a good time to get rid of any EMC or HDS disk and replace with the new IBM DS8700 system.
IBM System Storage TS7680 ProtecTIER Deduplication Gateway for System z
When it comes to virtual tape libraries that attach to mainframes, the two main players are IBM TS7700 series and Oracle StorageTek Virtual Storage Manager (VSM). However, mainframe clients with StorageTek equipment are growing frustrated over Oracle's lack of commitment for mainframe-attachable storage. To make matters worse, Oracle recently missed a key delivery date for their latest enterprise tape drive.
What's new this week is that IBM now supports native IP-based asynchronous replication of virtual tapes at distance, from one TS7680 to another TS7680. This replaces the method of replication using the back end disk features. The problem with using disk replication is that all the virtual tapes will be copied over. Instead, the ProtecTIER administrator can decide which subset of virtual tapes should be replicated to the remote site, and that can reduce both storage requirements as well as bandwidth costs. See the [Announcement Letter] for more details.
The new [IBM System Storage Tape Controller 3592 Model C07] is an upgrade to the previous C06 controller. Like the C06, the new 3592-C07 can have up to four FICON (4Gbps) ports, four FC ports, and connect up to 16 drives. The difference is that the C07 supports 8Gbps speed FC ports, and can support the [new TS1140 tape drives that were announced on May 9]. A cool feature of the C07 is that it has a built-in library manager function for the mainframe. On the previous models, you had to have a separate library manager server.
Crossroads ReadVerify Appliance (3222-RV1)
IBM has entered an agreement to resell [Crossroads ReadVerify Appliance], or "RV1" for short. The RV1 is a 1U-high server with software that gathers information on the utilization, performance and health for a physical tape environment, such as an IBM TS3500 Tape Library. The RV1 also offers a feature called "ArchiveVerify" which validates long-term retention archive tapes, providing an audit trail on the readability of tape media. This can be useful for tape libraries attached behind IBM Information Archive compliance storage solution, or the IBM Scale-Out Network Attached Storage (SONAS).
As an added bonus, Crossroads has great videos! Here's one, titled [Tape Sticks]
Linear Tape File System (LTFS) Library Edition Version 2.1
While the hardware is all refreshed, the overall "scale-out" architecture is unchanged. Kudos to the XIV development team for designing a system that is based entirely on commodity hardware, allowing new hardware generations to be introduced with minimal changes to the vast number of field-proven software features like thin provisioning, space-efficient read-only and writeable snapshots, synchronous and asynchronous mirroring, and Quality of Service (QoS) performance classes.
The new XIV Gen3 features an Infiniband interconnect, faster 8Gbps FC ports, more iSCSI ports, faster motherboard and processors, SAS-NL 2TB drives, 24GB cache memory per XIV module, all in a single frame IBM rack that supports the IBM Rear Door Heat Exchanger. The results are a 2x to 4x boost in performance for various workloads. Here are some example performance comparisons:
Disclaimer: Performance is based on measurements and projections using standard IBM benchmarks in a controlled environment. The actual throughput that any user will experience will vary depending upon considerations such as the amount of multiprogramming in the user's job stream, the I/O configuration, the storage configuration, and the workload processed. Therefore, no assurance can be given that an individual user will achieve throughput improvements equivalent to the performance ratios stated here. Your mileage may vary.
In a Statement of Direction, IBM also has designed the Gen3 modules to be "SSD-ready" which means that you can insert up to 500GB of Solid-State drive capacity per XIV module, up to 7.5TB in a fully-configured 15 module frame. This SSD would act as an extension of DRAM cache, similar to how Performance Accelerator Modules (PAM) on IBM N series.
IBM will continue to sell XIV Gen2 systems for the next 12-18 months, as some clients like the smaller 1TB disk drives. The new Gen3 only comes with 2TB drives. There are some clients that love the XIV so much, that they also use it for less stringent Tier 2 workloads. If you don't need the blazing speed of the new Gen3, perhaps the lower cost XIV Gen2 might be a great fit!
As if I haven't said this enough times already, the IBM XIV is a Tier-1, high-end, enterprise-class disk storage system, optimized for use with mission critical workloads on Linux, UNIX and Windows operating systems, and is the ideal cost-effective replacement for EMC Symmetrix VMAX, HDS USP-V and VSP, and HP P9000 series disk systems, . Like the XIV Gen2, the XIV Gen3 can be used with IBM System i using VIOS, and with IBM System z mainframes running Linux, z/VM or z/VSE. If you run z/OS or z/TPF with Count-Key-Data (CKD) volumes and FICON attachment, go with the IBM System Storage DS8000 instead, IBM's other high-end disk system.
Well it's Wednesday, and you know what that means... IBM Announcements.
(Normally, announcements are on Tuesdays, but we moved this one over to Wednesday to line up with our big launch event in Pinehurst, NC. )
A lot was announced today, so I decided to break it up into several separate posts. I will start with our Enterprise Systems: DS8870, TS7700 Release 3, and XIV Gen3.
Enterprise systems are the servers, storage and software at the core of an enterprise IT infrastructure. Enterprise systems enable a private cloud infrastructure at enterprise scale, with flexible service delivery models that provide dynamic efficiency for resource and workload management. They make sure critical data is always available across the enterprise, making it accessible in new ways so that actionable insights can be derived from advanced and operational analytics. They also provide ultimate security, ensuring the integrity of critical data while mitigating risk and providing assured compliance.
IBM System Storage DS8870® disk system
This new storage system is the next generation in IBM's DS8000 series, based on IBM's POWER7 chipset. Each CEC can have 2, 4, 8 or 16 cores. Like the DS8800, you can have a mix of 2.5-inch and 3.5-inch disk drives of different speeds and capacities, up to 1,536 drives in a four-frame configuration. The maximum cache is now 1TB usable. The combination of faster chipset and more cache can triple performance for some workloads!
All DS8870s ship standard with all Full Disk Encryption (FDE-capable) drives. The problem in the past was that people would buy DS8000 with non-FDE drives, and then later want to activate encryption, and discovered that they have to swap out their drives with those with the encryption chip built in. Now, all drives on the DS8870 will have the encryption chip. This also allows Easy Tier sub-volume automated tiering to move encrypted data between all media types.
Flash optimization with DS8000 Easy Tier can improve performance up to 3 times with 3% of data on solid-state storage. Easy Tier is easy to deploy and runs automatically.
Support of the American National Standards Institute's (ANSI) T10 Data Integrity Field (DIF) standard. This is a feature that the mainframe has had for years, and is now being extended to distributed operating systems. The concept is simple. When sending data between server and storage, generate a checksum at the source, and then validate the checksum at the target. When you write a block of data, the server generates the checksum, and the DS8870 validates the checksum on arrival. When you read the data back, the DS8870 generates the checksum, and the server validates it on arrival. This ensures that data was not corrupted in between. There is a great write-up on IBM developerWorks: [End-to-end data protection using T10 standard data integrity field].
Energy Efficient. The DS8870 consumes less energy than its predecessor, the DS8800. For example, a fully-configured four-frame DS8870 with 1,536 disk drives consumes only 23.2kW, compared to the same number of drives in a DS8800 consumed 26.3 kW. By comparison, the DS8700 with five frames and 1,024 drives consumed 29.2kW.
Support for new System z load balancing algorithm. System z Workload Manager now interacts with the DS8870 I/O Priority Manager to optimize designated Quality of Service (QoS) levels. We have also the fastest operational analytics solution with DB2 list Prefetch cache optimization with DS8870 High Performance FICON (zHPF) integration. This solution increases DB2 query performance up to 11 times with disk, and up to 60 times with solid-state drives (SSD). File scans are up to 30 percent faster using DS8870 zHPF support for sequential access methods (QSAM, BPAM, and BSAM).
VMware vStorage APIs for Array Integration (VAAI) support. Why should the IBM DS8800 series support VMware when IBM already offers great VMware support with SAN Volume Controller (SVC), Storwize V7000 and XIV storage sytsems? Good question. This was hotly debated between development and marketing. Several DS8000 customers have already added SVC to provide full VMware VAAI support. As a consultant, I am neither development nor marketing, but felt it necessary to weigh in on my opinion on this. The DS8000 is a consolidation platform. According to one analyst survey, 22 percent of companies run on a single disk platform, so for DS8000 to be the one, it needs to support VMware and exploit these special APIs.
Six Nines Availability. Critical enterprise systems need to deliver continuous data availability, or very close to it. IBM solutions can help deliver up to six “nines” of availability, or 99.9999 percent when combining DS8000 Metro Mirror and GDPS Hyperswap. That's less than 30 seconds of downtime per year.
The TS7700 Release 3 represents a refresh to our existing virtual tape libraries. These are mainframe-only, offered in two models: TS7720 is a disk-only device, and the TS7740 is a blended disk-and-tape solution.
Industry standard hardware encryption. This applies to user data stored on the TS7700 system cache (disk), and for data transferred between TS7700 systems. This is especially important for regulations, like Payment Card Industry Data Security Standard (PCI-DSS). In previous models, the data would not be encrypted until it was moved off disk and written to tape. Now, it is encrypted the minute in lands on the disk cache, and stays encrypted as it is replicated from one TS7700 to another in the grid.
Up to 4 Million logical volume capacity. This is twice the previous support.
More physical capacity for TS7720 systems. The maximum capacity for the disk-only model is raised from 440TB to 620TB, representing a 40 percent increase.
My latest book "Inside System Storage: Volume V" is now available!
I have published my fifth volume in my "Inside System Storage" series! Currently, it is only available in Paperback. My editor, Susan Pollard, is hoping to have the eBook and Hardcover versions ready for Cyber Monday. The foreword was written by my Dr. Sondra Ashmore.
You can order this, and all my other books, in all formats, directly from my [Author Spotlight] page. The paperback will also be available soon from other online booksellers, search for ISBN 978-1-300-26223-7.
Improved Scalability. A new Multi-system Manager (MSM) server reduces the operational complexity for large and multi-site XIV deployments. Previously, admins connected directly to XIV boxes. If you had 10 admins logged in, then every XIV box was managing 10 admin conversations. The new MSM acts as a go-between. The admins connect to the MSM, and the MSM connects to the XIV boxes. The MSM polls and caches the status of each XIV, greatly increasing the number of XIV boxes that an admin can manage.
Enhanced User Interface. A new Multi-system Manager server reduces the operational complexity for large and multi-site XIV deployments. We also added support for IPsec and US. Government (USGv6) certification for admistering the XIV over IPv6 networks. The XIV Mobile Dashboard app for iPhone and iPad is spiffed up. Finally, the GUI has been internationalized and translated to the Japanese language.
Enhanced Integration for Cloud. For OpenStack, XIV now offers a Nova-volume driver which provides persistent storage to OpenStack compute nodes. The Nova task force is now looking to move storage into its own project called Cinder. For VMware, XIV has full support for Site Recovery Manager (SRM) v4.1 and v5.0 releases. XIV now also supports the Microsoft System Center Virtual Machine Manager, which can manage Hyper-V, VMware and Citrix XenServer hypervisors.
Smaller entry point. The original XIV supported 1TB and 2TB drives, with the smallest offering being 27TB usable. When IBM introduced the XIV Gen3, the two choices were 2TB and 3TB disk drives. Unfortunately, this meant that the initial entry model was now 55TB in size, and each additional module would be more expensive as well. IBM is now going to offer 1TB support for XIV Gen3 for a lower price point, these are actually 2TB drives with half the capacity turned off.
Fellow Blogger BarryB mentions "chunk size" in his post [Blinded by the light],as it relates to Symmetrix Virtual Provisioning capability. Here is an excerpt:
I mean, seriously, who else but someone who's already implemented thin provisioning would really understand the implications of "chunk" size enough to care?
For those of you who don't know what the heck "chunk size" means (now listen up you folks over at IBM who have yet to implement thin provisioning on your own storage products), a "chunk" is the term used (and I think even trademarked by 3PAR) to refer to the unit of actual storage capacity that is assigned to a thin device when it receives a write to a previously unallocated region of the device.
For reference, Hitachi USP-V uses I think a 42MB chunk, XIV NEXTRA is definitely 1MB, and 3PAR uses 16K or 256K (depending upon how you look at it).
Thin Provisioning currently offered in IBM System Storage N serieswas technically "implemented" by NetApp, and that the Thin Provisioning that will be offered in our IBM XIV Nextrasystems will have been acquired from XIV. Lest I remind you that many of EMC's products were developed by other companies first, then later acquired by EMC, so no need for you to throw rocks from your glass houses in Hopkington.
"Thin provisioning" was first introduced by StorageTek in the 1990's and sold by IBM under the name of RAMAC Virtual Array (RVA). An alternative approach is "Dynamic Volume Expansion" (DVE). Rather than giving the host application a huge 2TB LUN but actually only use 50GB for data, DVE was based on the idea that you only give out 50GB they need now, but could expand in place as more space was required. This was specifically designed to avoid the biggest problem with "Thin Provisioning" which back then was called "Net Capacity Load" on the IBM RVA, but today is now referred to as "over-subscription". It gave Storage Administrators greater control over their environment with no surprises.
In the same manner as Thin Provisioning, DVE requires a "chunk size" to work with. Let's take a look:
On the DS4000 series, we use the term "segment size", and indicate that the choice of a segment size can have some influence on performance in both IOPS and throughput. Smaller segment sizes increase the request rate (IOPS) by allowing multiple disk drives to respond to multiple requests. Large segment sizes increase the data transfer rate(Mbps) by allowing multiple disk drives to participate in one I/O request. The segment size does not actually change what is stored in cache, just what is stored on the disk itself.It turns out in practice there is no advantage in using smaller sizes with RAID 1; only in a few instances does this help with RAID-5 if you can writea full stripe at once to calculate parity on outgoing data. For most business workloads, 64KB or 128KB are recommended. DVE expands by the same number of segments across all disks in the RAID rank, so for example in a 12+P rank using 128KB segment sizes, the chunk size would be thirteen segments, about 1.6MB in size.
SAN Volume Controller
On the SAN Volume Controller, we call this "extent size" and allow it to be various values 64MB to 512MB. Initially,IBM only managed four million extents, so this table was used to explain the maximum amount that could be managedby an SVC system (up to 8 nodes) depending on extent size selected.
IBM thought that since we externalized "segment size" on the DS4000, we should do the same for the SANVolume Controller. As it turned out, SVC is so fast up in the cache, that we could not measure any noticeable performance difference based on extent size. We did have a few problems. First, clients who chose 16MB andthen grew beyond the 64TB maximum addressable discovered that perhaps they should have chosen something larger.Second, clients called in our help desk to ask what size to choose and how to determine the size that was rightfor them. Third, we allowed people to choose different extent sizes per managed disk group, but that preventsmovement or copies between groups. You can only copy between groups that use the same extent size. The generalrecommendation now is to specify 256MB size, and use that for all managed disk groups across the data center.
The latest SVC expanded maximum addressability to 8PB, still more than most people have today in their shops.
Getting smarter each time we introduce new function, we chose 1GB chunks for the DS8000. Based on a mainframebackground, most CKD volumes are 3GB, 9GB, or 27GB in size, and so 1GB chunks simplified this approach. Spreadingthese 1GB chunks across multiple RAID ranks greatly reduced hot-spots that afflict other RAID-based systems.(Rather than fix the problem by re-designing the architecture, EMC will offer to sell you software to help you manually move data around inside the Symmetrix after the hot-spot is identified)
Unlike EMC's virtual positioning, IBM DS8000 dynamic volume expansion does work on CKD volumes for our System z mainframe customers.
The trade-off in each case was between granularity and table space. Smaller chunks allow finer control on the exact amount allocated for a LUN or volume, but larger chunks reduced the number of chunks managed. With our advanced caching algorithms, changes in chunk size did not noticeably impact performance. It is best just to come up with a convenient size, and either configure it as fixed in the architecture, or externalize it as a parameter with a good default value.
Meanwhile, back at EMC, BarryB indicates that they haven't determined the "optimal" chunk size for their newfunction. They plan to run tests and experiments to determine which size offers the best performance, and thenmake that a fixed value configured into the DMX-4. I find this funny coming from the same EMC that won't participate in [standardized SPC benchmarks] because they feel that performance is a personal and private matter between a customer and their trusted storage vendor, that all workloads are different, and you get the idea. Here's another excerpt:
Back at the office, they've taking to calling these "chunks" Thin Device Extents (note the linkage back to EMC's mainframe roots), and the big secret about the actual Extent size is...(wait for it...w.a.i.t...for....it...)...the engineers haven't decided yet!
That's right...being the smart bunch they are, they have implemented Symmetrix Virtual Provisioning in a manner that allows the Extent size to be configured so that they can test the impact on performance and utilization of different sizes with different applications, file systems and databases. Of course, they will choose the optimal setting before the product ships, but until then, there will be a lot of modeling, simulation, and real-world testing to ensure the setting is "optimal."
Finally, BarryB wraps up this section poking fun at the chunk sizes chosen by other disk manufacturers. I don't knowwhy HDS chose 42MB for their chunk size, but it has a great[Hitchiker's Guide to the Galaxy]sound to it, answering the ultimate question to life, the universe and everything. Hitachi probably went to theirDeep Thought computer and asked how big should their "chunk size" be for their USP-V, and the computer said: 42.Makes sense to me.
I have to agree that anything smaller than 1MB is probably too small. Here's the last excerpt:
Now, many customers and analysts I've spoken to have in fact noted that Hitachi's "chunk" size is almost ridiculously large; others have suggested that 3PAR's chunks are so small as to create performance problems (I've seen data that supports that theory, by the way).
Well, here's the thing: the "right" chunk size is extremely dependent upon the internal architecture of the implementation, and the intersection of that ideal with the actual write distribution pattern of the host/application/file system/database.
So my suggestion to EMC is, please, please, please take as much time as you need to come up with the perfect"chunk size" for this, one that handles all workloads across a variety of operating systems and applications, from solid-state Flash drives to 1TB SATA disk. Take months or years, as long as it takes. The rest of the world is in no hurry, as thin provisioning or dynamic volume expansion is readily available on most other disk systems today.
Maybe if you ask HDS nicely, they might let you ask their computer.
By combining multiple components into a single "integrated system", IBM can offer a blended disk-and-tape storage solutions. This provides the best of both worlds, high speed access using disk, while providing lower costs and more energy efficiency with tape. According to a study by the Clipper Group, tape can be 23 times less expensive than disk over a 5 year total cost of ownership (TCO).
I've also covered Hierarchical Storage Management, such as my post [Seven Tiers of Storage at ABN Amro], and my role as lead architect for DFSMS on z/OS in general, and DFSMShsm in particular.
However, some explanation might be warranted in the use of these two terms in regards to SONAS. In this case, ILM refers to policy-based file placement, movement and expiration on internal disk pools. This is actually a GPFS feature that has existed for some time, and was tested to work in this new configuration. Files can be individually placed on either SAS (15K RPM) or SATA (7200 RPM) drives. Policies can be written to move them from SAS to SATA based on size, age and days non-referenced.
HSM is also a form of ILM, in that it moves data from SONAS disk to external storage pools managed by IBM Tivoli Storage Manager. A small stub is left behind in the GPFS file system indicating the file has been "migrated". Any reference to read or update this file will cause the file to be "recalled" back from TSM to SONAS for processing. The external storage pools can be disk, tape or any other media supported by TSM. Some estimate that as much as 60 to 80 percent of files on NAS have low reference and should be stored on tape instead of disk, and now SONAS with HSM makes that possible.
This distinction allows the ILM movement to be done internally, within GPFS, and the HSM movement to be done externally, via TSM. Both ILM and HSM movement take advantage of the GPFS high-speed policy engine, which can process 10 million files per node, run in parallel across all interface nodes. Note that TSM is not required for ILM movement. In effect, SONAS brings the policy-based management features of DFSMS for z/OS mainframe to all the rest of the operating systems that access SONAS.
HTTP and NIS support
In addition to NFS v2, NFS v3, and CIFS, the SONAS v1.1.1 adds the HTTP protocol. Over time, IBM plans to add more protocols in subsequent releases. Let me know which protocols you are interested in, so I can pass that along to the architects designing future releases!
SONAS v1.1.1 also adds support for Network Information Service (NIS), a client/server based model for user administration. In SONAS, NIS is used for netgroup and ID mapping only. Authentication is done via Active Directory, LDAP or Samba PDC.
SONAS already had synchronous replication, which was limited in distance. Now, SONAS v1.1.1 provides asynchronous replication, using rsync, at the file level. This is done over Wide Area Network (WAN) across to any other SONAS at any distance.
Interface modules can now be configured with either 64GB or 128GB of cache. Storage now supports both 450GB and 600GB SAS (15K RPM) and both 1TB and 2TB SATA (7200 RPM) drives. However, at this time, an entire 60-drive drawer must be either all one type of SAS or all one type of SATA. I have been pushing the architects to allow each 10-pack RAID rank to be independently selectable. For now, a storage pod can have 240 drives, 60 drives of each type of disk, to provide four different tiers of storage. You can have up to 30 storage pods per SONAS, for a total of 7200 drives.
An alternative to internal drawers of disk is a new "Gateway" iRPQ that allows the two storage nodes of a SONAS storage pod to connect via Fibre Channel to one or two XIV disk systems. You cannot mix and match, a storage pod is either all internal disk, or all external XIV. A SONAS gateway combined with external XIV is referred to as a "Smart Business Storage Cloud" (SBSC), which can be configured off premises and managed by third-party personnel so your IT staff can focus on other things.
See the Announcement Letters for the SONAS [hardware] and [software] for more details.
For those who are wondering how this positions against IBM's other NAS solution, the IBM System Storage N series, the rule of thumb is simple. If your capacity needs can be satisfied with a single N series box per location, use that. If not, consider SONAS instead. For those with non-IBM NAS filers that realize now that SONAS is a better approach, IBM offers migration services.
Both the Information Archive and the SONAS can be accessed from z/OS or Linux on System z mainframe, from "IBM i", AIX and Linux on POWER systems, all x86-based operating systems that run on System x servers, as well as any non-IBM server that has a supported NAS client.
This week, July 26-30, 2010, I am in Washington DC for the annual [2010 System Storage Technical University]. As with last year, we have joined forces with the System x team. Since we are in Washington DC this time, IBM added a "Federal Track" to focus on government challenges and solutions. So, basically, offering attendees the option to attend three conferences for one low price.
This conference was previously called the "Symposium", but IBM changed the name to "Technical University" to emphasize the technical nature of the conference. No marketing puffery like "Journey to the Private Cloud" here! Instead, this is bona fide technical training, qualifying attendees to count this towards their Continuing Professional Education (CPE).
(Note to my readers:The blogosphere is like a playground. In the center are four-year-olds throwing sand into each other's faces, while mature adults sit on benches watching the action, and only jumping in as needed. For example, fellow blogger Chuck Hollis (EMC) got sand in his face for promising to resign if EMC ever offered a tacky storage guarantee, and then [failed to follow through on his promise] when it happened.
Several of my readers asked me to respond to another EMC blogger's latest [fistful of sand].
A few months ago, fellow blogger Barry Burke (EMC) committed to [stick to facts] in posts on his Storage Anarchist blog. That didn't last long! BarryB apparently has fallen in line with EMC's over-promise-then-under-deliver approach. Unfortunately, I will be busy covering the conference and IBM's robust portfolio of offerings, so won't have time to address BarryB's stinking pile of rumor and hearsay until next week or later. I am sorry to disappoint.)
This conference is designed to help IT professionals make their business and IT infrastructure more dynamic and, in the process, help reduce costs, mitigate risks, and improve service. This technical conference event is geared to IT and Business Managers, Data Center Managers, Project Managers, System Programmers, Server and Storage Administrators, Database Administrators, Business Continuity and Capacity Planners, IBM Business Partners and other IT Professionals. This week will offer over 300 different sessions and hands-on labs, certification exams, and a Solutions Center.
For those who want a quick stroll through memory lane, here are my posts from past events:
In keeping up with IBM's leadership in Social Media, IBM Systems Lab Services and Training team running this event have their own [Facebook Fan Page] and
[blog]. IBM Technical University has a Twitter account [@ibmtechconfs], and hashtag #ibmtechu. You can also follow me on Twitter [@az990tony].
Continuing my week in Chicago, for the IBM Storage Symposium 2008, we had sessions that focused on individual products. IBM System Storage SAN Volume Controller (SVC) was a popular topic.
SVC - Everything you wanted to know, but were afraid to ask!
Bill Wiegand, IBM ATS, who has been working with SAN Volume Controller since it was first introduced in 2003. answered some frequently asked questions about IBM System Storage SAN Volume Controller.
Do you have to upgrade all of your HBAs, switches and disk arrays to the recommended firmware levels before upgrading SVC? No. These are recommended levels, but not required. If you do plan to update firmware levels, focus on the host end first, switches next, and disk arrays last.
How do we request special support for stuff not yet listed on the Interop Matrix?
Submit an RPQ/SCORE, same as for any other IBM hardware.
How do we sign up for SVC hints and tips? Go to the IBM
[SVC Support Site] and select the "My Notifications" under the "Stay Informed" box on the right panel.
When we call IBM for SVC support, do we select "Hardware" or "Software"?
While the SVC is a piece of hardware, there are very few mechanical parts involved. Unless there are sparks,
smoke, or front bezel buttons dangling from springs, select "Software". Most of the questions are
related to the software components of SVC.
When we have SVC virtualizing non-IBM disk arrays, who should we call first?
IBM has world-renown service, with some of IT's smartest people working the queues. All of the major storage vendors play nice
as part of the [TSAnet Agreement when a mutual customer is impacted.
When in doubt, call IBM first, and if necessary, IBM will contact other vendors on your behalf to resolve.
What is the difference between livedump and a Full System Dump?
Most problems can be resolved with a livedump. While not complete information, it is generally enough,
and is completely non-disruptive. Other times, the full state of the machine is required, so a Full System Dump
is requested. This involves rebooting one of the two nodes, so virtual disks may temporarily run slower on that
What does "svc_snap -c" do?The "svc_snap" command on the CLI generates a snap file, which includes the cluster error log and trace files from all nodes. The "-c" parameter includes the configuration and virtual-to-physical mapping that can be useful for
disaster recovery and problem determination.
I just sent IBM a check to upgrade my TB-based license on my SVC, how long should I wait for IBM to send me a software license key?
IBM trusts its clients. No software license key will be sent. Once the check clears, you are good to go.
During migration from old disk arrays to new disk arrays, I will temporarily have 79TB more disk under SVC management, do I need to get a temporary TB-based license upgrade during the brief migration period?
Nope. Again, we trust you. However, if you are concerned about this at all, contact IBM and they will print out
a nice "Conformance Letter" in case you need to show your boss.
How should I maintain my Windows-based SVC Master Console or SSPC server?
Treat this like any other Windows-based server in your shop, install Microsoft-recommended Windows updates,
run Anti-virus scans, and so on.
Where can I find useful "How To" information on SVC?
Specify "SAN Volume Controller" in the search field of the
[IBM Redbooks vast library of helpful books.
I just added more managed disks to my managed disk group (MDG), can I get help writing a script to redistribute the extents to improve wide-striping performance?
Yes, IBM has scripting tools available for download on
[AlphaWorks]. For example, svctools will take
the output of the "lsinfo" command, and generate the appropriate SVC CLI to re-migrate the disks around to optimize
performance. Of course, if you prefer, you can use IBM Tivoli Storage Productivity Center instead for a more
Any rules of thumb for sizing SVC deployments?
IBM's Disk Magic tool includes support for SVC deployments. Plan for 250 IOPS/TB for light workloads,
500 IOPS/TB for average workloads, and 750 IOPS/TB for heavy workloads.
Can I migrate virtual disks from one manage disk group (MDG) to another of different extent size?
Yes, the new Vdisk Mirroring capability can be used to do this. Create the mirror for your Vdisk between the
two MDGs, wait for the copy to complete, and then split the mirror.
Can I add or replace SVC nodes non-disruptively? Absolutely, see the Technotes
[SVC Node Replacement page.
Can I really order an SVC EE in Flamingo Pink? Yes. While my blog post that started all
this [Pink It and Shrink It] was initially just some Photoshop humor, the IBM product manager for SVC accepted this color choice as an RPQ option.
The default color remains Raven Black.
Well, it's Tuesday again, and that means more IBM announcements!
Today, IBM announced the enhanced IBM System Storage DS3200 disk system.It is in our DS3000 series, the DS3200 is SAS-attach, DS3300 is iSCSI-attach, and DS3400 is FC-attach. All of them support up to 48 drives, which can be a mix of SAS and SATA drives.
The DS3200 supports the following operating environments (see IBM's [Interop Matrix] for details):
Linux (both Linux-x86 and Linux on POWER)
With today's announcements, the DS3200 can be used to boot from, as well as contain data. This is ideal to combine with IBM BladeCenter. With the IBM BladeCenter you can have 14 blades, either x86 or POWER based processors, attached to a DS3200 via SAS switch modules in the back of the chassis.
Let's take an example of how this can be used for a Scale-Out File Services[SoFS] deployment.
First, we start with servers. We can have either three [IBM System x3650] servers, but this would use up all six of the direct-attach ports. Instead, we'll choose the [BladeCenter H chassis], with three HS21 blades for SoFS, and that leaves us with eleven empty blade slots we could put in a management node, or other blades to run applications.
SAS connectivity modules
The IBM BladeCenter [SAS Connectivity Module] allows the blade servers to connect to a DS3200. Two of them fit right in the back of the BladeCenter chassis, providing full redundancy without consuming additional rack space.
DS3200 and EXP3000 expansion drawers
We'll have one DS3200 controller with twelve internal drives, and three expansion EXP3000 drawers with twelve drives each, for a total of 48 drives. Using 1TB SATA, this would be 48 TB raw capacity.
The end result? You get a 48TB NAS scalable storage solution, supporting up to 7500 concurrent CIFS and NFS users, with up to 700 MB/sec with large block transfers. By using BladeCenter, you can expand performance by adding more blades to the Chassis, or have some blades running SAP or Oracle RAC have direct read/write access to the SoFS data.
Just another example on how IBM can bring together all the components of a solution to provide customer value!
Did IBM XIV force EMC's hand to announce VMAXe? Let's take a stroll down memory lane.
In 2008, IBM XIV showed the world that it could ship a Tier-1, high-end, enterprise-class system using commodity parts. Technically, prior to its acquisition by IBM, the XIV team had boxes out in production since 2005. EMC incorrectly argued this announcement meant the death of the IBM DS8000. Just because EMC was unable to figure out how to have more than one high-end disk product, doesn't mean IBM or other storage vendors were equally challenged. Both IBM XIV and DS8000 are Tier-1, high-end, enterprise-class storage systems, as are the IBM N series N7900 and the IBM Scale-Out Network Attached Storage (SONAS).
In April 2009, EMC followed IBM's lead with their own V-Max system, based on Symmetrix Engenuity code, but on commodity x86 processors. Nobody at EMC suggested that the V-Max meant the death of their other Symmetrix box, the DMX-4, which means that EMC proved to themselves that a storage vendor could offer multiple high-end disk systems. Hitachi Data Systems (HDS) would later offer the VSP, which also includes some commodity hardware as well.
In July 2009, analysts at International Technology Group published their TCO findings that IBM XIV was 63 percent less expensive than EMC V-Max, in a whitepaper titled [COST/BENEFIT CASE
FOR IBM XIV STORAGE SYSTEM Comparing Costs for IBM XIV and EMC V-Max Systems]. Not surprisingly, EMC cried foul, feeling that EMC V-Max had not yet been successful in the field, it was too soon to compare newly minted EMC gear with a mature product like XIV that had been in production accounts for several years. Big companies like to wait for "Generation 1" of any new product to mature a bit before they purchase.
To compete against IBM XIV's very low TCO, EMC was forced to either deeply discount their Symmetrix, or counter-offer with lower-cost CLARiiON, their midrange disk offering. An ex-EMCer that now works for IBM on the XIV sales team put it in EMC terms -- "the IBM XIV provides a Symmetrix-like product at CLARiiON-like prices."
(Note: Somewhere in 2010, EMC dropped the hyphen, changing the name from V-Max to VMAX. I didn't see this formally announced anywhere, but it seems that the new spelling is the officially correct usage. A common marketing rule is that you should only rename failed products, so perhaps dropping the hyphen was EMC's way of preventing people from searching older reviews of the V-Max product.)
This month, IBM introduced the IBM XIV Gen3 model 114. The analysts at ITG updated their analysis, as there are now more customers that have either or both products, to provide a more thorough comparison. Their latest whitepaper, titled [Cost/Benefit Case for IBM XIV Systems: Comparing Cost
Structures for IBM XIV and EMC VMAX Systems], shows that IBM maintains its substantial cost savings advantage, representing 69 percent less Total Cost of Ownership (TCO) than EMC, on average, over the course of three years.
In response, EMC announced its new VMAXe, following the naming convention EMC established for VNX and VNXe. Customers cannot upgrade VNXe to VNX, nor VMAXe to VMAX, so at least EMC was consistent in that regard. Like the IBM XIV and XIV Gen3, the new EMC VMAXe eliminated "unnecessary distractions" like CKD volumes and FICON attachment needed for the IBM z/OS operating system on IBM System z mainframes. Fellow blogger Barry Burke from EMC explains everything about the VMAXe in his blog post [a big thing in a small package].
So, you have to wonder, did IBM XIV force EMC's hand into offering this new VMAXe storage unit? Surely, EMC sales reps will continue to lead with the more profitable DMX-4 or VMAX, and then only offer the VMAXe when the prospective customer mentions that the IBM XIV Gen3 is 69 percent less expensive. I haven't seen any list or street prices for the VMAXe yet, but I suspect it is less expensive than VMAX, on a dollar-per-GB basis, so that EMC will not have to discount it as much to compete against IBM.
This week I got a comment on my blog post [IBM Announces another SSD Disk offering!]. The exchange involved Solid State Disk storage inside the BladeCenter and System x server line. Sandeep offered his amazing performance results, but we have no way to get in contact with him. So, for those interested, I have posted on SlideShare.net a quick five-chart presentation on recent tests with various SSD offerings on the eX5 product line here: