This blog is for the open exchange of ideas relating to IBM Systems, storage and storage networking hardware, software and services.
(Short URL for this blog: ibm.co/Pearson )
Tony Pearson is a Master Inventor, Senior IT Architect and Event Content Manager for [IBM Systems for IBM Systems Technical University] events. With over 30 years with IBM Systems, Tony is frequent traveler, speaking to clients at events throughout the world.
Lloyd Dean is an IBM Senior Certified Executive IT Architect in Infrastructure Architecture. Lloyd has held numerous senior technical roles at IBM during his 19 plus years at IBM. Lloyd most recently has been leading efforts across the Communication/CSI Market as a senior Storage Solution Architect/CTS covering the Kansas City territory. In prior years Lloyd supported the industry accounts as a Storage Solution architect and prior to that as a Storage Software Solutions specialist during his time in the ATS organization.
Lloyd currently supports North America storage sales teams in his Storage Software Solution Architecture SME role in the Washington Systems Center team. His current focus is with IBM Cloud Private and he will be delivering and supporting sessions at Think2019, and Storage Technical University on the Value of IBM storage in this high value IBM solution a part of the IBM Cloud strategy. Lloyd maintains a Subject Matter Expert status across the IBM Spectrum Storage Software solutions. You can follow Lloyd on Twitter @ldean0558 and LinkedIn Lloyd Dean.
Tony Pearson's books are available on Lulu.com! Order your copies today!
Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
The developerWorks Connections Platform is now in read-only mode and content is only available for viewing. No new wiki pages, posts, or messages may be added. Please see our FAQ for more information. The developerWorks Connections platform will officially shut down on March 31, 2020 and content will no longer be available. More details available on our FAQ. (Read in Japanese.)
Tonight PBS plans to air Season 38, Episode 6 of NOVA, titled [Smartest Machine On Earth]. Here is an excerpt from the station listing:
"What's so special about human intelligence and will scientists ever build a computer that rivals the flexibility and power of a human brain? In "Artificial Intelligence," NOVA takes viewers inside an IBM lab where a crack team has been working for nearly three years to perfect a machine that can answer any question. The scientists hope their machine will be able to beat expert contestants in one of the USA's most challenging TV quiz shows -- Jeopardy, which has entertained viewers for over four decades. "Artificial Intelligence" presents the exclusive inside story of how the IBM team developed the world's smartest computer from scratch. Now they're racing to finish it for a special Jeopardy airdate in February 2011. They've built an exact replica of the studio at its research lab near New York and invited past champions to compete against the machine, a big black box code -- named Watson after IBM's founder, Thomas J. Watson. But will Watson be able to beat out its human competition?"
Like most supercomputers, Watson runs the Linux operating system. The system runs 2,880 cores (90 IBM Power 750 servers, four sockets each, eight cores per socket) to achieve 80 [TeraFlops]. TeraFlops is the unit of measure for supercomputers, representing a trillion floating point operations. By comparison, Hans Morvec, principal research scientist at the Robotics Institute of Carnegie Mellon University (CMU) estimates that the [human brain is about 100 TeraFlops]. So, in the three seconds that Watson gets to calculate its response, it would have processed 240 trillion operations.
Several readers of my blog have asked for details on the storage aspects of Watson. Basically, it is a modified version of IBM Scale-Out NAS [SONAS] that IBM offers commercially, but running Linux on POWER instead of Linux-x86. System p expansion drawers of SAS 15K RPM 450GB drives, 12 drives each, are dual-connected to two storage nodes, for a total of 21.6TB of raw disk capacity. The storage nodes use IBM's General Parallel File System (GPFS) to provide clustered NFS access to the rest of the system. Each Power 750 has minimal internal storage mostly to hold the Linux operating system and programs.
When Watson is booted up, the 15TB of total RAM are loaded up, and thereafter the DeepQA processing is all done from memory. According to IBM Research, "The actual size of the data (analyzed and indexed text, knowledge bases, etc.) used for candidate answer generation and evidence evaluation is under 1TB." For performance reasons, various subsets of the data are replicated in RAM on different functional groups of cluster nodes. The entire system is self-contained, Watson is NOT going to the internet searching for answers.
Continuing this week's coverage of IBM's 3Q announcements, today it's all about storage for our mainframe clients.
IBM System Storage DS8700
IBM is the leader in high-end disk attached to mainframes, with the IBM DS8700 being our latest model in a long series of successful products in this space. Here are some key features:
Full Disk Encryption (FDE), which I mentioned in my post [Different Meanings of the word "Protect"]. FDE are special 15K RPM Fibre Channel drives that include their own encryption chip, so that IBM DS8700 can encrypt the data at rest without impacting performance of reads or writes. The encryption keys are managed by IBM Tivoli Key Lifecycle Manager (TKLM).
Easy Tier, which I covered in my post [DS8700 Easy Tier Sub Lun Automatic Migration] which offers what EMC promised but has yet to deliver, the ability to have CKD volumes and FBA LUNs to straddle the fence between Solid State Drives (SSD) and spinning disk. For example, a 54GB CKD volume could have 4GB on SSD and the remaining 50GB on spinning drives. The hottest extents are moved automatically to SSD, and the coldest moved down to spinning disk. To learn more about Easy Tier, watch my [7-minute video] on IBM [Virtual Briefing Center].
z/OS Distributed Data Backup (zDDB), announced this week, provides the ability for a program running on z/OS to backup data written by distributed operating systems like Windows or UNIX stored in FBA format. In the past, to backup FBA LUNs involved a program like IBM Tivoli Storage Manager client to read the data natively, send it over Ethernet LAN to a TSM Server, which could run on the mainframe and use mainframe resources. This feature eliminates the Ethernet traffic by allowing a z/OS program to read the FBA blocks through standard FICON channels, which can then be written to z/OS disk or tape resources. Here is the [Announcement Letter] for more details.
One program that takes advantage of this new zDDB feature already is Innovation's [FDRSOS], which I pronounce "fudder sauce". If you are an existing FDRSOS customer, now is a good time to get rid of any EMC or HDS disk and replace with the new IBM DS8700 system.
IBM System Storage TS7680 ProtecTIER Deduplication Gateway for System z
When it comes to virtual tape libraries that attach to mainframes, the two main players are IBM TS7700 series and Oracle StorageTek Virtual Storage Manager (VSM). However, mainframe clients with StorageTek equipment are growing frustrated over Oracle's lack of commitment for mainframe-attachable storage. To make matters worse, Oracle recently missed a key delivery date for their latest enterprise tape drive.
What's new this week is that IBM now supports native IP-based asynchronous replication of virtual tapes at distance, from one TS7680 to another TS7680. This replaces the method of replication using the back end disk features. The problem with using disk replication is that all the virtual tapes will be copied over. Instead, the ProtecTIER administrator can decide which subset of virtual tapes should be replicated to the remote site, and that can reduce both storage requirements as well as bandwidth costs. See the [Announcement Letter] for more details.
Are you tired of hearing about Cloud Computing without having any hands-on experience? Here's your chance. IBM has recently launched its IBM Development and Test Cloud beta. This gives you a "sandbox" to play in. Here's a few steps to get started:
Generate a "key pair". There are two keys. A "public" key that will reside in the cloud, and a "private" key that you download to your personal computer. Don't lose this key.
Request an IP address. This step is optional, but I went ahead and got a static IP, so I don't have to type in long hostnames like "vm353.developer.ihost.com".
Request storage space. Again, this step is optional, but you can request a 50GB, 100GB and 200GB LUN. I picked a 200GB LUN. Note that each instance comes with some 10 to 30GB storage already. The advantage to a storage LUN is that it is persistent, and you can mount it to different instances.
Start an "instance". An "instance" is a virtual machine, pre-installed with whatever software you chose from the "asset catalog". These are Linux images running under Red Hat Enterprise Virtualization (RHEV) which is based on Linux's kernel virtual machine (KVM). When you start an instance, you get to decide its size (small, medium, or large), whether to use your static IP address, and where to mount your storage LUN. On the examples below, I had each instance with a static IP and mounted the storage LUN to /media/storage subdirectory. The process takes a few minutes.
So, now that you are ready to go, what instance should you pick from the catalog? Here are three examples to get you started:
IBM WebSphere sMASH Application Builder
Base OS server to run LAMP stack
Next, I decided to try out one of the base OS images. There are a lot of books on Linux, Apache, MySQL and PHP (LAMP) which represents nearly 70 percent of the web sites on the internet. This instance let's you install all the software from scratch. Between Red Hat and Novell SUSE distributions of Linux, Red Hat is focused on being the Hypervisor of choice, and SUSE is focusing on being the Guest OS of choice. Most of the images on the "asset catalog" are based on SLES 10 SP2. However, there was a base OS image of Red Hat Enterprise Linux (RHEL) 5.4, so I chose that.
To install software, you either have to find the appropriate RPM package, or download a tarball and compile from source. To try both methods out, I downloaded tarballs of Apache Web Server and PHP, and got the RPM packages for MySQL. If you just want to learn SQL, there are instances on the asset catalog with DB2 and DB2 Express-C already pre-installed. However, if you are already an expert in MySQL, or are following a tutorial or examples based on MySQL from a classroom textbook, or just want a development and test environment that matches what your company uses in production, then by all means install MySQL.
This is where my SSH client comes in handy. I am able to login to my instance and use "wget" to fetch the appropriate files. An alternative is to use "SCP" (also part of PuTTY) to do a secure copy from your personal computer up to the instance. You will need to do everything via command line interface, including editing files, so I found this [VI cheat sheet] useful. I copied all of the tarballs and RPMs on my storage LUN ( /media/storage ) so as not to have to download them again.
Compiling and configuring them is a different matter. By default, you login as an end user, "idcuser" (which stands for IBM Developer Cloud user). However, sometimes you need "root" level access. Use "sudo bash" to get into root level mode, and this allows you to put the files where they need to be. If you haven't done a configure/make/make install in awhile, here's your chance to relive those "glory days".
In the end, I was able to confirm that Apache, MySQL and PHP were all running correctly. I wrote a simple index.php that invoked phpinfo() to show all the settings were set correctly. I rebooted the instance to ensure that all of the services started at boot time.
Rational Application Developer over VDI
This last example, I started an instance pre-installed with Rational Application Developer (RAD), which is a full Integrated Development Environment (IDE) for Java and J2EE applications. I used the "NX Client" to launch a virtual desktop image (VDI) which in this case was Gnome on SLES 10 SP2. You might want to increase the screen resolution on your personal computer so that the VDI does not take up the entire screen.
From this VDI, you can launch any of the programs, just as if it were your own personal computer. Launch RAD, and you get the familiar environment. I created a short Java program and launched it on the internal WebSphere Application Server test image to confirm it was working correctly.
If you are thinking, "This is too good to be true!" there is a small catch. The instances are only up and running for 7 days. After that, they go away, and you have to start up another one. This includes any files you had on the local disk drive. You have a few options to save your work:
Copy the files you want to save to your storage LUN. This storage LUN appears persistent, and continues to exist after the instance goes away.
Take an "image" of your "instance", a function provided in the IBM Developer and Test Cloud. If you start a project Monday morning, work on it all week, then on Friday afternoon, take an "image". This will shutdown your instance, and backup all of the files to your own personal "asset catalog" so that the next time you request an instance, you can chose that "image" as the starting point.
Another option is to request an "extension" which gives you another 7 days for that instance. You can request up to five unique instances running at the same time, so if you wanted to develop and test a multi-host application, perhaps one host that acts as the front-end web server, another host that does some kind of processing, and a third host that manages the database, this is all possible. As far as I can tell, you can do all the above from either a Windows, Mac or Linux personal computer.
Getting hands-on access to Cloud Computing really helps to understand this technology!
Continuing my quest to "set the record straight" about [IBM XIV Storage System] and IBM's other products, I find myself amused at some of the FUD out there. Some are almost as absurd as the following analogy:
Humans share over 50 percent of DNA with bananas. [source]
If you peel a banana, and put the slippery skin down on the sidewalk outside your office building, it couldpose a risk to your employees
If you peel a human, the human skin placed on the sidewalk in a similar manner might also pose similar risks.
Mr. Jones, who applied for the opening in your storage administration team, is a human being.
You wouldn't hire a banana to manage your storage, would you? This might be too risky!
The conclusion we are led to believe is that hiring Mr. Jones, a human being, is as risky as puttinga banana peel down on the sidewalk. Some bloggers argue that they are merely making a series of factual observations,and letting their readers form their own conclusions. For example, the IBM XIV storage system has ECC-protected mirrored cache writes. Some false claims about this were [properly retracted]using strike out font to show the correction made, other times the same statement appears in another post from the same blogger that[have not yet beenretracted] (Update: has now been corrected). Other bloggers borrow the false statement [for their own blog], perhaps not realizing theretractions were made elsewhere. Newspapers are unable to fix a previous edition, so are forced to publishretractions in future papers. With blogs, you can edit the original and post the changed version, annotated accordingly, so mistakes can be corrected quickly.
While it is possible to compare bananas and humans on a variety of metrics--weight, height, and dare I say it,caloric value--it misses the finer differences of what makes them different. Humans might share 98 percent withchimpanzees, but having an opposable thumb allows humans to do things that chimpanzeesother animals cannot.
Full Disclosure: I am neither vegetarian nor cannibal, and harbor no ill will toward bananas nor chimpanzees.No bananas or chimpanzees were harmed in the writing of this blog post. Any similarity between the fictitiousMr. Jones in the above analogy and actual persons, living or dead, is purely coincidental.
So let's take a look at some of IBM XIV Storage System's "opposable thumbs".
The IBM XIV system comes pre-formatted and ready to use. You don't have to spend weeks in meetings deciding betweendifferent RAID levels and then formatting different RAID ranks to match those decisions. Instead, you can start using the storage on the IBM XIV Storage System right away.
The IBM XIV offers consistent performance, balancing I/O evenly across all disk drive modules, even when performing SnapShot processing, or recovering from component failure. You don't have to try to separate data to prevent one workload from stealing bandwidth from another. You don't have to purchase extra software to determine where the "hot spots" are on the disk. You don't have to buy othersoftware to help re-locate and re-separate the data to re-balance the I/Os. Instead, you just enjoy consistentperformance.
The IBM XIV offers thin provisioning, allowing LUNs to grow as needed to accommodate business needs. You don'thave to estimate or over-allocate space for planned future projects. You don't have to monitor if a LUN is reaching80 or 90 percent full. You don't have to carve larger and larger LUNs and schedule time on the weekends to move thedata over to these new bigger spaces. Instead, you just write to the disk, monitoring the box as a whole, ratherthan individual LUNs.
The IBM XIV Storage System's innovative RAID-X design allows drives to be replaced with drives of any larger or smaller capacity. You don't have to find the exact same 73GB 10K RPM drive to match the existing 73GB 10K RPM drive that failed. Some RAID systems allow "larger than original" substitutions, for example a 146GB drive to replace a 73GB drive, but the added capacity is wasted, because of the way most RAID levels work. The problemis that many failures happen 3-5 years out, and disk manufacturers move on to bigger capacities and differentform factors, making it sometimes difficult to find an exact replacement or forcing customers to keep their own stockof spare drives. Instead, with the IBM XIV architecture, you sleep well at night, knowing it allows future drive capacities to act as replacements, and getting the full value and usage of that capacity.
In the case of IBM XIV Storage System, it is not clear whether
"Vendors" are those from IBM and IBM Business Partners, including bloggers like me employed by IBM,and "everybody else" includes IBM's immediate competitors, including bloggers employed by them.
-- or --
"Vendors" includes IBM and its competitors including any bloggers, so that "everybody else" refers instead to anyone not selling storage systems, but opinionated enough to not qualify as "objective third-party sources".
-- or --
"Vendors" includes official statements from IBM and its competitors, and "everybody else" refers to bloggerspresenting their own personal or professional opinions, that may or may not correspond to their employers.
That said, feel free to comment below on which of these you think the last two points of Steinhardt's rule istrying to capture. Certainly, I can't argue with the top two: a customer's own experience and the experiencesof other customers, which I mentioned previously in my post[Deceptively Delicious].
In that light, here is a 5-minute video on IBM TV with a customer testimonial from the good folksat [NaviSite], one of our manycustomer references for the IBM XIV Storage System.
I am still wiping the coffee off my computer screen, inadvertently sprayed when I took a sip while reading HDS' uber-blogger Hu Yoshida's post on storage virtualization and vendor lock-in.
HDS is a major vendor for disk storage virtualization, and Hu Yoshida has been around for a while, so I felt it was fair to disagree with some of the generalizations he made to set the record straight. He's been more careful ever since.
However, his latest post [The Greening of IT: Oxymoron or Journey to a New Reality] mentions an expert panel at SNW that includedMark O’Gara Vice President of Infrastructure Management at Highmark. I was not at the SNW conference last week in Orlando, so I will just give the excerpt from Hu's account of what happened:
"Later I had the opportunity to have lunch with Mark O’Gara. Mark is a West Point graduate so he takes a very disciplined approach to addressing the greening of IT. He emphasized the need for measurements and setting targets. When he started out he did an analysis of power consumption based on vendor specifications and came up with a number of 513 KW for his data center infrastructure....
The physical measurements showed that the biggest consumers of power were in order: Business Intelligence Servers, SAN Storage, Robotic tape Library, and Virtual tape servers....
Another surprise may be that tape libraries are such large consumers of power. Since tape is not spinning most of the time they should consume much less power than spinning disk - right? Apparently not if they are sitting in a robotic tape library with a lot of mechanical moving parts and tape drives that have to accelerate and decelerate at tremendous speeds. A Virtual Tape Library with de-duplication factor of 25:1 and large capacity disks may draw significantly less power than a robotic tape library for a given amount of capacity.
Obviously, I know better than to sip coffee whenever reading Hu's blog. I am down here in South America this week, the coffee is very hot and very delicious, so I am glad I didn't waste any on my laptop screen this time, especially reading that last sentence!
In that report, a 5-year comparison found that a repository based on SATA disk was 23 times more expensive overall, and consumed 290 times more energy, than a tape library based on LTO-4 tape technology. The analysts even considered a disk-based Virtual Tape Library (VTL). Focusing just on backups, at a 20:1 deduplication ratio, the VTL solution was still 5 times per expensive than the tape library. If you use the 25:1 ratio that Hu Yoshida mentions in his post above, that would still be 4 times more than a tape library.
I am not disputing Mark O'Gara's disciplined approach. It is possible that Highmark is using a poorly written backup program, taking full backups every day, to an older non-IBM tape library, in a manner that causes no end of activity to the poor tape robotics inside. But rather than changing over to a VTL, perhaps Mark might be better off investigating the use of IBM Tivoli Storage Manager, using progressive backup techniques, appropriate policies, parameters and settings, to a more energy-efficient IBM tape library.In well tuned backup workloads, the robotics are not very busy. The robot mounts the tape, and then the backup runs for a long time filling up that tape, all the meanwhile the robot is idle waiting for another request.
(Update: My apologies to Mark and his colleagues at Highmark. The above paragraph implied that Mark was using badproducts or configured them incorrectly, and was inappropriate. Mark, my full apology [here])
If you do decide to go with a Virtual Tape Library, for reasons other than energy consumption, doesn't it make sense to buy it from a vendor that understands tape systems, rather than buying it from one that focuses on disk systems? Tape system vendors like IBM, HP or Sun understand tape workloads as well as related backup and archive software, and can provide better guidance and recommendations based on years of experience. Asking advice abouttape systems, including Virtual Tape Libraries, from a disk vendor is like asking for advice on different types of bread from your butcher, or advice about various cuts of meat at the bakery.
The butchers and bakers might give you answers, but it may not be the best advice.
Last July, IBM and EMC traded blog postings over SPC-1 benchmark results. Fellow EMC bloggerChuck Hollis wrote his post [Does Anyone Take The SPC Seriously?]. Here is an excerpt:
I think most storage users have figured this out. We've never done an SPC test, and probably will never do one. Anyone is free, however, to download the SPC code, lash it up to their CLARiiON, and have at it.
I responded with [Getting Under EMC Skin], and then followed up with a series explaining IBM SVC and SPC benchmarks here:
So what is the good news?Yesterday, our friends at NetApp took up Chuck's challenge and posted results on their FAS3040 as well as their EMC CLARiiON devices. IBM sells the FAS3040 under the name IBM System Storage N5300 disk system. Knowing that NetApp maintains excellent performance when it is doing point-in-time copies, NetApp ran both with and without on both boxes. I include DS4700 and DS4800 as well for comparison purposes, but only have them without FlashCopy running.
NetApp FAS3040 (IBM N5300)
NetApp FAS3040 (IBM N5300)
EMC CLARiiON CX3-40
IBM DS4700 Express
EMC CLARiiON CX3-40
One would expect some performance degradation with a box running point-in-time copies at the same time it is reading and writing data, but NetApp/IBM N5300 does not degrade by much, but EMC's drops a significant amount.
So what is the bad news? Last October, I welcomed HDS USP-V to the [Super High-End Club], but now we need to invite Texas Memory Systems as well.In 2006, I posted [Hybrid, Solid State and the future of RAID], and poked fun at Texas Memory Systems using the slogan "World's Fastest Storage", which at the time that honor belonged to IBM SAN Volume Controller instead.The VP of Texas Memory Systems, Woody Hutsell, explained the only reason their solid-state disk system, RAMSAN-320, didn't have faster results is that they didn't have the fastest IBM server to run against it. It may not surprise you that nearly everyone's SPC benchmarks use IBM servers because IBM has the fastest servers as well. I didn't have a million-dollar System p UNIX server to send Woody for this, but it looks like they have finally gotten one, and a new RAMSAN-400 device, as they have posted their latest results.
Texas Memory Systems RAMSAN-400
IBM SAN Volume Controller 4.2
EMC doesn't publish numbers for their Symmetrix box, despite their announcement of faster SSD drives. They claim that SSD drives make their overall disk system performance faster, but without SPC benchmarks, we will never know. If you have a Symmetrix, this YouTube video may help you decide where it belongs:
Wrapping up this week's theme on the XO laptop, I decided to take on thechallenge of printing. I managed to print from my XO laptop to my laserjet printer.I checked the One Laptop Per Child [OLPC] website,and found there is no built-in support for printers, but there have been several peopleasking how to print from the XO, so here are the steps I did to make it happen.
(Note: I did all of these steps successfully on my Qemu-emulated system first, and then performed them on my XO laptop)
Step 1: Determine if you have an acceptable printer
The XO laptop can only connect to a printer via USB cable or over the network.Check your printer to see if it supports either of these two options. In my case, my printer is connected to my Linksys hub that offers Wi-Fi in my home.
The XO runs a modified version of Red Hat's Fedora 7, so we need to also determineif the printer is supported on Linux.Check the [Open Printing Database]for the level of support. This database has come up with the following ranking system.Printers are categorized according to how well they work under Linux and Unix. The ratings do not pertain to whether or not the printer will be auto-recognized or auto-configured, but merely to the highest level of functionality achieved.
Perfectly - everything the printer can do is working also under Linux
Mostly - work almost perfectly - funny enhanced resolution modes may be missing, or the color is a bit off, but nothing that would make the printouts not useful
Partially - mostly don't work; you may be able to print only in black and white on a color printer, or the printouts look horrible
Paperweight - These printers don't work at all. They may work in the future, but don't count on it
If your printer only supports a parallel cable connection, or does not have a high enough ranking above, go buy another printer. The [Linux Foundation] websiteoffers a list of suggested printers and tutorials.
In my case, I have a Brother HL5250-DN black-and-white laserjet printer connected over a network to Windows XP, OS X and my other Linux systems. It is rated as supporting Linux perfectly, so I decided to use this for my XO laptop.
Step 2: Install Common UNIX Printing System (CUPS)
Technically, Linux is not UNIX, but for our purposes, close enough. Start the Terminalactivity, use "su" to change to root, and then use "yum" to install CUPS. Yum will automatically determine what other packages are needed, in this case paps and tmpwatch. Once installed, use "/usr/sbin/cupsd" to get the CUPS daemon started, and add this to the end ofrc.local so that it gets started every time you reboot.
Click graphic on the left to see larger view
[olpc@xo-10-CC-6F ~]$ subash-3.2# yum install cups...Total download size = 3.0 MIs this OK [y/N]? y
To download the appropriate drivers, you may need a browser that can handle file downloads. I have triedto do this with the built-in Browse activity (aka Gecko) but encountered problems. I have both Opera and Firefox installed, but I will focus on Opera for this effort.I also installed the older184.108.40.206 version of the Flash player (worked better than the latest 220.127.116.11 version) and Java JRE.Follow the OLPC Wiki instructions for [Opera, Adobe Flash,and Sun Java] installation, thenverify with the following [Java and Flash] testers.
Step 4: Download drivers and packages unique for your printer
In my case, I used Opera to get to the [Brother Linux Driver Homepage], and downloaded the RPM's for LPR and CUPS wrapper. These are the ones listed under "Drivers for Red Hat, Mandrake (Mandriva), SuSE". I saved these under "/home/olpc" directory.
By default, the root user has no password. However, you will need it to be something for later steps,so here is the process to create a root password. I set mine to "tony" which normallywould be considered too simple a password, but ignore those messages and continue.We will remove it in step 8 (below) to put things back to normal.
[olpc@xo-10-CC-6F ~]$ subash-3.2# passwdChanging password for user root.New UNIX password: tonyBAD PASSWORD: it is too shortRetype new UNIX password: tonypasswd: all authentication tokens updated successfullybash-3.2# exit[olpc@xo-10-CC-6F ~]$
Step 6: Launch CUPS administration
Here I followed the instructions in Robert Spotswood's [Printing In Linux with CUPS] tutorial.Launch the Opera browser, and enter "http://localhost:631/admin" as the URL. The localhostrefers to the laptop itself, and 631 is the special port that CUPS listens to from browsers. You can alsouse 127.0.0.1 as a shortcut for "localhost", and can be used interchangeably.
In my case, it detected both of my networked printers, so I selected the HL5250DN, entered thelocation of my PPD file "/usr/share/cups/model/HL5250DN.ppd" that was created in Step 4. I set the URI to "lpd://192.168.0.75/binary_p1" per the instructions [Network Setting in CUPS based Linux system] in the Brother FAQ page. I chage the page size from "A4" to "Letter".I set this printer as the default printer. When it asks for userid and password, that is whereyou would enter "root" for the user, and "tony" or whatever you decided to set your root password to.
Select "Print a Test Page" to verify that everything is working.
Step 7: Printing actual files
Sadly, I don't know Opera well enough to know how to print from there. So, I went over to my trustedFirefox browser. Select File->Page Setup to specify the settings, File->Print Preview tosee what it will look like, and then File->Print to send it to the printer.
To print the file "out.txt" that is in your /home/olpc directory, for example, enter"file:///home/olpc/out.txt" as the URL of the firefox browser. This will show the file,which you can then print to your printer. I had to specify 200% scaling otherwise the fontswere too small to read.
Step 8: Remove the "root" password
If you want to remove the root password, here are the steps.
[olpc@xo-10-CC-6F ~]$ suPassword: tonybash-3.2# passwd -d rootRemoving password for user root.passwd: Successbash-3.2# exit[olpc@xo-10-CC-6F ~]$
Now the problem is that there is no way to print stuff from any of the Sugar activities. The best place toput in print support would be the Journal activity. Along the bottom where the mounted USB keys arelocated could be an icon for a printer, and dragging a file down to the printer ojbect could cause it tobe send to the printer.
The alternative is to write some scripts invocable from the Terminal activity to determine what isin the journal, and send them to LPR with the appropriate parameters.
I did not have time to do either of these, but perhaps someone out there can take on that as a project.
As we wrap up the year, people's thoughts turn to archive anddata retention.
The [Robert Frances Group] have put out a research paper titled Optimizing Data Retention and Archiving - November 2007 that helps IT executives understand the cost differences for a disk-only archive approach versus disk/tape archive approach and how an [IBM System Storage DR550] offering can help address the long-term storage archive requirements with a world-class storage strategy that reduces cost, improves efficiency and supports compliance. Here is an excerpt:
Ongoing legal, audit, and regulatory requirementswill continue to drive IT groups to improvearchive policies, processes, strategy, andefficiency. The choice of which technologies touse will have a profound impact on the success ofsuch efforts, since technologies like the DR550embody many aspects of the strategy, processes,and policies that must be decided upon. When itcomes to tape, IBM's DR550 is unique inproviding that support. Competitors tout disk-onlysolutions as the wave of the future, but researchindicates otherwise. The most basic benefits arecost and mobility, and despite the various vendorproclamations to the contrary, tape is still only afraction of the cost of disk and will remain so inthe foreseeable future.
This paper is yet another nail in the coffin of EMC Centera.In his post [Anyone Naughty on Your List…], Jon W Toigo points to an eBay fire sale of an EMC Centera Gen 4.
There has never been a better time to switch from EMC Centera to theIBM System Storage DR550.
IBM doesn't publicly report subset numbers on individual product lines, but we are growing, albeit single-digit growth, on the high-end with our IBM System Storage DS8000 and DS6000 series products. Single digit growth is not "booming", but it is what we expected in this space, so it is not like we are"feeling the chill" as Robin stated.Obviously, if the U.S. market overall is doing poorly, then it must be from something else. IBM's success appears to be from organic growth in our Asia and Europe markets, and taking marketshare away from the top two contenders, EMC and HDS. Here are my thoughts why:
EMC is remodeling its kitchen
Not happy with its status as #1 disk hardware specialty shop, EMC is admirably trying to redefine itself as an ["information infrastructure"] company, buying up software companies and introducing new storage services. [Byte and Switch] reports onEMC's recent acquisitions:
EMC is the latest vendor to pin its colors to the SaaS mast, revealing its plan to offer SaaS-based archiving services during its recent Innovation Day in Boston.
EMC gave another clear indication of its SaaS intentions last month, when it spent $76 million to acquire online backup specialist Mozy.
IBM has offered[Managed Storage Services] foryears through our Global Technology Services (GTS) division. Gartner recognized IBM as the #1 leader in storageservices, with three times more revenues than EMC in this space.
As with a restaurant that is remodeling its kitchen, it can expect a temporary drop inrevenue. If it is done right, customers will come back to a bigger brighter restaurant. If not, the restaurant re-opens as a much smaller lesser version of itself. Recent events this year might incent EMC to get that kitchen done quickly:
A recent [class-action lawsuit]might result in having EMC's "86 percent male" sales force goes to sexual harassment sensitivity training, takingtime away from selling high-end storage arrays in the field. Analysts consider "high-end" boxes as those costingover $300,000 US dollars. Because of the money involved, there is a lot of competition for high-end storage, so face-to-face time with prospective customers is crucial to making the sale.Anytime any vendor is mentioned in a lawsuit (andcertainly IBM has had its share in the past, as Chuck Hollis correctly points out in the comment below), priorities get shifted, and there is potential dip in revenues.
Dell acquires EMC's rival EqualLogic. Dell resold EMC midrange storage, like CLARiiON, so this should notimpact their high-end storage sales. While Dell will be allowed to sell EMC until 2011, this new acquisition mightmean Dell leads with the EqualLogic offerings, and that could potentially reduce EMC revenues in the midrange space.
IBM went through a similar phase in the 1990's, redefining itself from an "IT Technology" company, intoa "Systems, Software and Services" company. These transitions can't be done in a quarter, or even a year, theytake several years. IBM lost business to EMC in the 1990s, but is back with a stronger portfolio in the 2000's, and so IBM's kitchen remodeling effort appears to be paying off. We will see what happens with EMC in a few years.
HDS puts on the white lab coats
Meanwhile, HDS appears interested in taking over as #1 disk hardware specialty shop.For years, Hitachi was the stereotypical JCM (Japanese IBM-compatible manufacturer) that made well-engineered"me, too" storage arrays. They would see what innovators like IBM and EMC were doing, and copy them. Recently,however, they seemed to have changed strategy, introducing new featuresand functions on their high-end USP-V device, like[Dynamic Provisioning].
The problem is that customers don't want to feel like [Guinea pigs] in an experimental lab, especially withmission-critical data that they trust to their most-available, most-reliable high-end disk storage systems.Like IBM and EMC and the rest of the major storage vendors, Hitachi has top-notch engineers making quality products, but new features scare people, and so there is a lag in the adoption of new technologies.
In our youth, we might have preferred beer with recent born-on dates, and tequila aged less than 90 days. But as weget older, we switch to drinks like wine and whiskey, aged years, not weeks. The same is true for themarketplace. New start-ups and other "early adopters"might be willing to try fresh new features and functions on their storage systems, but more established enterprises prefer storage with more mature and stable microcode.Storage admins want to leave at the end of the day, knowing that the data will still be there the next morning. In tough financial times, many established companies want the technological equivalent to ["comfort food"], nothing spicy or exotic, but simplehearty fare that fills the belly and keeps you satisfied.
Recognizing this, IBM often introduces new features and functions on its midrange lines first, and position them accordingly. Once customers are comfortable with the concepts, IBM then can consider moving them into the high-end lines. For example, dynamic volume expansion was introduced on the DS4000 and SAN Volume Controller first, and once proven safe and effective, brought over to the DS8000 series. This strategy has served us well.
Well those are my theories. If you have a different explanation of why storage vendors are not doing well in thehigh-end, drop me a comment!
It's official! My "blook" Inside System Storage - Volume I is now available.
This blog-based book, or “blook”, comprises the first twelve months of posts from this Inside System Storage blog,165 posts in all, from September 1, 2006 to August 31, 2007. Foreword by Jennifer Jones. 404 pages.
IT storage and storage networking concepts
IBM strategy, hardware, software and services
Disk systems, Tape systems, and storage networking
Storage and infrastructure management software
Second Life, Facebook, and other Web 2.0 platforms
IBM’s many alliances, partners and competitors
How IT storage impacts society and industry
You can choose between hardcover (with dust jacket) or paperback versions:
This is not the first time I've been published. I have authored articles for storage industry magazines, written large sections of IBM publications and manuals, submitted presentations and whitepapers to conference proceedings, and even had a short story published with illustrations by the famous cartoon writer[Ted Rall].
But I can say this is my first blook, and as far as I can tell, the first blook from IBM's many bloggers on DeveloperWorks, and the first blook about the IT storage industry.I got the idea when I saw [Lulu Publishing] run a "blook" contest. The Lulu Blooker Prize is the world's first literary prize devoted to "blooks"--books based on blogs or other websites, including webcomics. The [Lulu Blooker Blog] lists past year winners. Lulu is one of the new innovative "print-on-demand" publishers. Rather than printing hundredsor thousands of books in advance, as other publishers require, Lulu doesn't print them until you order them.
I considered cute titles like A Year of Living Dangerously, orAn Engineer in Marketing La-La land, or Around the World in 165 Posts, but settled on a title that matched closely the name of the blog.
In addition to my blog posts, I provide additional insights and behind-the-scenes commentary. If you go to the Luluwebsite above, you can preview an entire chapter in its entirety before purchase. I have added a hefty 56-page Glossary of Acronyms and Terms (GOAT) with over 900 storage-related terms defined, which also doubles as an index back to the post (or posts) that use or further explain each term.
So who might be interested in this blook?
Business Partners and Sales Reps looking to give a nice gift to their best clients and colleagues
Managers looking to reward early-tenure employees and retain the best talent
IT specialists and technicians wanting a marketing perspective of the storage industry
Mentors interested in providing motivation and encouragement to their proteges
Educators looking to provide books for their classroom or library collection
Authors looking to write a blook themselves, to see how to format and structure a finished product
Marketing personnel that want to better understand Web 2.0, Second Life and social networking
Analysts and journalists looking to understand how storage impacts the IT industry, and society overall
College graduates and others interested in a career as a storage administrator
And yes, according to Lulu, if you order soon, you can have it by December 25.