Tony Pearson is a Master Inventor and Senior IT Architect for the IBM Storage product line at the
IBM Systems Client Experience Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services.
(Short URL for this blog: ibm.co/Pearson )
My books are available on Lulu.com! Order your copies today!
Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Continuing coverage of my week in Washington DC for the annual [2010 System Storage Technical University], I attended several XIV sessions throughout the week. There were many XIV sessions. I could not attend all of them. Jack Arnold, one of my colleagues at the IBM Tucson Executive Briefing Center, often presents XIV to clients and Business Partners. He covered all the basics of XIV architecture, configuration, and features like snapshots and migration. Carlos Lizarralde presented "Solving VMware Challenges with XIV". Ola Mayer presented "XIV Active Data Migration and Disaster Recovery".
Here is my quick recap of two in particular that I attended:
XIV Client Success Stories - Randy Arseneau
Randy reported that IBM had its best quarter ever for the XIV, reflecting an unexpected surge shortly after my blog post debunking the DDF myth last April. He presented successful case studies of client deployments. Many followed a familiar pattern. First, the client would only purchase one or two XIV units. Second, the client would beat the crap out of them, putting all kinds of stress from different workloads. Third, the client would discover that the XIV is really as amazing as IBM and IBM Business Partners have told them. Finally, in the fourth phase, the client would deploy the XIV for mission-critical production applications.
A large US bank holding company managed to get 5.3 GB/sec from a pair of XIV boxes for their analytics environment. They now have 14 XIV boxes deployed in mission-critical applications.
A large equipment manufacturer compared the offerings among seven different storage vendors, and IBM XIV came out the winner. They now have 11 XIV boxes in production and another four boxes for development/test. They have moved their entire VMware infrastructure to IBM XIV, running over 12,000 guest instances.
A financial services company bought their first XIV in early 2009 and now has 34 XIV units in production attached to a variety of Windows, Solaris, AIX, Linux servers and VMware hosts. Their entire Microsoft Exchange was moved from HP and EMC disk to IBM XIV, and experienced noticeable performance improvement.
When a University health system replaced two competitive disk systems with XIV, their data center temperature dropped from 74 to 68 degrees Fahrenheit. In general, XIV systems are 20 to 30 percent more energy efficient per usable TB than traditional disk systems.
A service provider that had used EMC disk systems for over 10 years evaluated the IBM XIV versus upgrading to EMC V-Max. The three year total cost of ownership (TCO) of EMC's V-Max was $7 Million US dollars higher, so EMC counter-proposed CLARiiON CX4 instead. But, in the end, IBM XIV proved to be the better fit, and now the customer is happy having made the switch.
The manager of an information communications technology service provider was impressed that the XIV was up and running in just a couple of days. They now have over two dozen XIV systems.
Another XIV client had lost all of their Computer Room Air Conditioning (CRAC) units for several hours. The data center heated up to 126 degrees Fahrenheit, but the customer did not lose any data on either of their two XIV boxes, which continued to run in these extreme conditions.
Optimizing XIV Performance - Brian Cormody
This session was an update from the [one presented last year] by Izhar Sharon. Brian presented various best practices for optimizing the performance when using specific application workloads with IBM XIV disk systems.
Oracle ASM: Many people allocate lots of small LUNs, because this made sense a long time ago when all you had was just a bunch of disks (JBOD). In fact, many of the practices that DBAs use to configure databases across disks become unnecessary with XIV. Wth XIV, you are better off allocating a few number of very large LUNs from the XIV. The best option was a 1-volume ASM pool with 8MB AU stripe. A single LUN can contain multiple Oracle databases. A single LUN can be used to store all of the logs.
VMware: Over 70 percent of XIV customers use it with VMware. For VMFS, IBM recommends allocating a few number of large LUNs. You can specify the maximum of 2181 GB. Do not use VMware's internal LUN extension capability, as IBM XIV already has thin provisioning and works better to allow XIV to do this for you. XIV Snapshots provide crash-consistent copies without all the VMware overhead of VMware Snapshots.
SAP: For planning purposes, the "SAPS" unit equates roughly to 0.4 IOPS for ERP OLTP workloads, and 0.6 IOPS for BW/BI OLAP workloads. In general, an XIV can deliver 25-30,000 IOPS at 10-15 msec response time, and 60,000 IOPS at 30 msec response time. With SAP, our clients have managed to get 60,000 IOPS at less than 15 msec.
Microsoft Exchange: Even my friends in Redmond could not believe how awesome XIV was during ESRP testing. Five Exchange 2010 servers connected two a pair of XIV boxes using the new 2TB drawers managed 40,000 mailboxes at the high profile (0.15 IOPS per mailbox). Another client found four XIV boxes (720 drives) was able to handle 60,000 mailboxes (5GB max), which would have taken over 4000 drives if internal disk drives were used instead. Who said SANs are obsolete for MS Exchange?
Asynchronous Replication: IBM now has an "Async Calculator" to model and help design an XIV async replication solution. In general, dark fiber works best, and MPLS clouds had the worst results. The latest 10.2.2 microcode for the IBM XIV can now handle 10 Mbps at less than 250 msec roundtrip. During the initial sync between locations, IBM recommends setting the "schedule=never" to consume as much bandwidth as possible. If you don't trust the bandwidth measurements your telco provider is reporting, consider testing the bandwidth yourself with [iPerf] open source tool.
By combining multiple components into a single "integrated system", IBM can offer a blended disk-and-tape storage solutions. This provides the best of both worlds, high speed access using disk, while providing lower costs and more energy efficiency with tape. According to a study by the Clipper Group, tape can be 23 times less expensive than disk over a 5 year total cost of ownership (TCO).
I've also covered Hierarchical Storage Management, such as my post [Seven Tiers of Storage at ABN Amro], and my role as lead architect for DFSMS on z/OS in general, and DFSMShsm in particular.
However, some explanation might be warranted in the use of these two terms in regards to SONAS. In this case, ILM refers to policy-based file placement, movement and expiration on internal disk pools. This is actually a GPFS feature that has existed for some time, and was tested to work in this new configuration. Files can be individually placed on either SAS (15K RPM) or SATA (7200 RPM) drives. Policies can be written to move them from SAS to SATA based on size, age and days non-referenced.
HSM is also a form of ILM, in that it moves data from SONAS disk to external storage pools managed by IBM Tivoli Storage Manager. A small stub is left behind in the GPFS file system indicating the file has been "migrated". Any reference to read or update this file will cause the file to be "recalled" back from TSM to SONAS for processing. The external storage pools can be disk, tape or any other media supported by TSM. Some estimate that as much as 60 to 80 percent of files on NAS have low reference and should be stored on tape instead of disk, and now SONAS with HSM makes that possible.
This distinction allows the ILM movement to be done internally, within GPFS, and the HSM movement to be done externally, via TSM. Both ILM and HSM movement take advantage of the GPFS high-speed policy engine, which can process 10 million files per node, run in parallel across all interface nodes. Note that TSM is not required for ILM movement. In effect, SONAS brings the policy-based management features of DFSMS for z/OS mainframe to all the rest of the operating systems that access SONAS.
HTTP and NIS support
In addition to NFS v2, NFS v3, and CIFS, the SONAS v1.1.1 adds the HTTP protocol. Over time, IBM plans to add more protocols in subsequent releases. Let me know which protocols you are interested in, so I can pass that along to the architects designing future releases!
SONAS v1.1.1 also adds support for Network Information Service (NIS), a client/server based model for user administration. In SONAS, NIS is used for netgroup and ID mapping only. Authentication is done via Active Directory, LDAP or Samba PDC.
SONAS already had synchronous replication, which was limited in distance. Now, SONAS v1.1.1 provides asynchronous replication, using rsync, at the file level. This is done over Wide Area Network (WAN) across to any other SONAS at any distance.
Interface modules can now be configured with either 64GB or 128GB of cache. Storage now supports both 450GB and 600GB SAS (15K RPM) and both 1TB and 2TB SATA (7200 RPM) drives. However, at this time, an entire 60-drive drawer must be either all one type of SAS or all one type of SATA. I have been pushing the architects to allow each 10-pack RAID rank to be independently selectable. For now, a storage pod can have 240 drives, 60 drives of each type of disk, to provide four different tiers of storage. You can have up to 30 storage pods per SONAS, for a total of 7200 drives.
An alternative to internal drawers of disk is a new "Gateway" iRPQ that allows the two storage nodes of a SONAS storage pod to connect via Fibre Channel to one or two XIV disk systems. You cannot mix and match, a storage pod is either all internal disk, or all external XIV. A SONAS gateway combined with external XIV is referred to as a "Smart Business Storage Cloud" (SBSC), which can be configured off premises and managed by third-party personnel so your IT staff can focus on other things.
See the Announcement Letters for the SONAS [hardware] and [software] for more details.
For those who are wondering how this positions against IBM's other NAS solution, the IBM System Storage N series, the rule of thumb is simple. If your capacity needs can be satisfied with a single N series box per location, use that. If not, consider SONAS instead. For those with non-IBM NAS filers that realize now that SONAS is a better approach, IBM offers migration services.
Both the Information Archive and the SONAS can be accessed from z/OS or Linux on System z mainframe, from "IBM i", AIX and Linux on POWER systems, all x86-based operating systems that run on System x servers, as well as any non-IBM server that has a supported NAS client.
Well, I'm back safely from my tour of Asia. I am glad to report that Tokyo, Beijing and Kuala Lumpur are pretty much how I remember them from the last time I was there in each city. I have since been fighting jet lag by watching the last thirteen episodes of LOST season 6 and the series finale.
Recently, I have started seeing a lot of buzz on the term "Storage Federation". The concept is not new, but rather based on the work in database federation, first introduced in 1985 by [A federated architecture for information management] by Heimbigner and McLeod. For those not familiar with database federation, you can take several independent autonomous databases, and treat them as one big federated system. For example, this would allow you to issue a single query and get results across all the databases in the federated system. The advantage is that it is often easier to federate several disparate heterogeneous databases than to merge them into a single database. [IBM Infosphere Federation Server] is a market leader in this space, with the capability to federate DB2, Oracle and SQL Server databases.
Storage expansion: You want to increase the storage capacity of an existing storage system that cannot accommodate the total amount of capacity desired. Storage Federation allows you to add additional storage capacity by adding a whole new system.
Storage migration: You want to migrate from an aging storage system to a new one. Storage Federation allows the joining of the two systems and the evacuation from storage resources on the first onto the second and then the first system is removed.
Safe system upgrades: System upgrades can be problematic for a number of reasons. Storage Federation allows a system to be removed from the federation and be re-inserted again after the successful completion of the upgrade.
Load balancing: Similar to storage expansion, but on the performance axis, you might want to add additional storage systems to a Storage Federation in order to spread the workload across multiple systems.
Storage tiering: In a similar light, storage systems in a Storage Federation could have different capacity/performance ratios that you could use for tiering data. This is similar to the idea of dynamically re-striping data across the disk drives within a single storage system, such as with 3PAR's Dynamic Optimization software, but extends the concept to cross storage system boundaries.
To some extent, IBM SAN Volume Controller (SVC), XIV, Scale-Out NAS (SONAS), and Information Archive (IA) offer most, if not all, of these capabilities. EMC claims its VPLEX will be able to offer storage federation, but only with other VPLEX clusters, which brings up a good question. What about heterogenous storage federation? Before anyone accuses me of throwing stones at glass houses, let's take a look at each IBM solution:
IBM SAN Volume Controller
The IBM SAN Volume Controller has been doing storage federation since 2003. Not only can IBM SAN Volume Controller bring together storage from a variety of heterogenous storage, the SVC cluster itself can be a mix of different hardware models. You can have a 2145-8A4 node pair, 2145-8G4 node pair, and the new 2145-CF8 node pair, all combined together into a single SVC cluster. Upgrading SVC hardware nodes in an SVC cluster is always non-disruptive.
IBM XIV storage system
The IBM XIV has two kinds of independent modules. Data modules have processor, cache and 12 disks. Interface modules are data modules with additional processor, FC and Ethernet (iSCSI) adapters. Because these two modules play different roles in an XIV "colony", that number of each type is predetermined. Entry-level six-module systems have 2 interface and 4 data modules. Full 15-module systems have 6 interface and 9 data modules. Individual modules can be added or removed non-disruptively in an XIV.
IBM Scale-Out NAS
The SONAS is comprised of three kinds of nodes that work together in concert. A management node, one or more interface nodes, and two or more storage nodes. The storage nodes are paired to manage up to 240 nodes in a storage pod. Individual interface or data nodes can be added or removed non-disruptively in the SONAS. The underlying technology, the General Parallel File System, has been doing storage federation since 1996 for some of the largest top 500 supercomputers in the world.
IBM Information Archive (IA)
For the IA, there are 1, 2 or 3 nodes, which manages a set of collections. A collection can either be file-based using industry-standard NAS protocols, or object-based using the popular System Storage™ Archive Manager (SSAM) interface. Normally, you have as many collections as you have nodes, but nodes are powerful enough to manage two collections to provide N-1 availability. This allows a node to be removed, and a new node added into the IA "colony", in a non-disruptive manner.
Even in an ant colony, there are only a few types of ants, with typically one queen, several males, and lots of workers. But all the ants are red. You don't see colonies that mix between different species of ants. For databases, federation was a way to avoid the much harder task of merging databases from different platforms. For storage, I am surprised people have latched on to the term "federation", given our mixed results in the other "federations" we have formed, which I have conveniently (IMHO) ranked from least effective to most effective:
The Union of Soviet Socialist Republics (USSR)
My father used to say, "If the Soviet Union were in charge of the Sahara desert, they would run out of sand in 50 years." The [Soviet Union] actually lasted 68 years, from 1922 to 1991.
The United Nations (UN)
After the previous League of Nations failed, the UN was formed in 1945 to facilitate cooperation in international law, international security, economic development, social progress, human rights, and the achieving of world peace by stopping wars between countries, and to provide a platform for dialogue.
The European Union (EU)
With the collapse of the Greek economy, and the [rapid growth of debt] in the UK, Spain and France, there are concerns that the EU might not last past 2020.
The United States of America (USA)
My own country is a federation of states, each with its own government. California's financial crisis was compared to the one in Greece. My own state of Arizona is under boycott from other states because of its recent [immigration law]. However, I think the US has managed better than the EU because it has evolved over the past 200 years.
The Organization of the Petroleum Exporting Countries [OPEC]
Technically, OPEC is not a federation of cooperating countries, but rather a cartel of competing countries that have agreed on total industry output of oil to increase individual members' profits. Note that it was a non-OPEC company, BP, that could not "control their output" in what has now become the worst oil spill in US history. OPEC was formed in 1960, and is expected to collapse sometime around 2030 when the world's oil reserves run out. Matt Savinar has a nice article on [Life After the Oil Crash].
United Federation of Planets
The [Federation] fictitiously described in the Star Trek series appears to work well, an optimistic view of what federations could become if you let them evolve long enough.
Given the mixed results with "federation", I think I will avoid using the term for storage, and stick to the original term "scale-out architecture".
Continuing my coverage of the IBM Dynamic Infrastructure Executive Summit at the Fairmont Resort in Scottsdale, Arizona, we had a day full main-tent sessions. Here is a quick recap of the sessions presented in the afternoon.
Taming the Information Explosion
Doug Balog, IBM Vice President and Disk Storage Business Line Executive, presented on the information explosion. Storage Admins are focused on managing storage growth and the related costs and complexity, proper forecasting and capacity planning, and backup administration. IBM's strategy is to help clients in the following areas:
Storage Efficiency - getting the most use out of the resources you invest
Service Delivery - ensuring that information gets to the right people at the right time
Data Protection - protecting data against unethical tampering, unauthorized access, and unexpected loss and corruption
Cory Vokey, Senior Manager of IT Systems Operations at Research in Motion, Ltd., the people who bring you BlackBerry phone service, provided a client testimonial for the XIV storage system. Before the XIV, RIM suffered high storage costs and per-volume software licensing. Over the past 15 months, RIM deployed XIV as a corporate standard. With the XIV, they have had 100 percent up-time, and enjoyed 50 percent costs savings compared to their previous storage systems. They have increased capacity 300 percent, without any increase to their storage admin staff. XIV has greatly improved their procurement process, as they no longer need to "true up" their software licenses to the volume of data managed, a sore point with their previous storage vendor.
Mainframe Innovations and Integration
Tom Rosamillia, IBM General Manager of the System z mainframe platform, presented on mainframe servers. After 40 years, IBM's mainframe remains the gold standard, able to handle hundreds of workloads on a single server, facilitating immediate growth with scalability. The key values of the System z mainframe are:
Industry leading virtualization, management and qualities of service
A comprehensive portfolio for business intelligence and data warehousing
The premier platform for modernizing the enterprise
A large and growing portfolio of leading-applications ISV support
Steve Phillips, CIO of Avnet, presented the client testimonial for their use of a System z10 mainframe. Last year, Avnet was ranked Fortune's Number One "Most admired" for Technology distribution. Avnet distributes technology from 300 suppliers to over 100,000 resellers, ISVs and end users. They have modernized their system running SAP on System z with DB2 as the database management system, using Hypersockets virtual LAN inside the server to communicate between logical partitions (LPARs). The folks at Avnet especially like the ability for on-the-fly re-assignment of capacity. This is used for end-of-quarter peak processing, and to adjust between test and development workloads. They also like the various special purpose engines available:
z Integrated Information Processor (zIIP) for DB2 workloads
z Application Assist Processor (zAAP) for Java processing under WebSphere
Integrated Facility for Linux (IFL) for Linux applications
Cloud Computing: Real Capabilities, Real Stories
Mike Hill, IBM Vice President of Enterprise Initiatives, presented on IBM's leadership in cloud computing. He covered three trends that are driving IT today. First, there is a consumerization and industrialization of IT interfaces. Second, a convergence of the infrastructure that is driving a new focus on standards. Third, delivering IT as a service has brought about new delivery choices. The result is cloud computing, with on-demand self-service, ubiquitous network access, location-independent resource pooling, rapid elasticity, and flexible pricing models. Government agencies and businesses in Retail, Manufacturing and Utilities are leading the charge to cloud computing.
Mike covered IBM's five cloud computing deployment models, and shared his views on which workloads might be ready for cloud, and which may not be there yet. Organizations are certainly seeing significant results: reduced labor costs, improved capital utilization, reduced provisioning cycle times, improved quality through reduced software defects, and reduced end user IT support costs.
Mitch Daniels, Director of Technology at ManTech International Corporation, presented the customer testimonial for an IBM private cloud for Development and Test. Mantech chose a private cloud as they work with US Federal agencies like Department of Defense, Homeland Security and the Intelligence community. The private cloud was built from:
IBM Cloudburst virtualized server environment
Tivoli Unified Process to document process and workflow
Tivoli Service Automation Manager to request, deliver and manage IT services
Tivoli Self-Service Portal and Service Catalog to allow developers and testers to request resources as needed
The result: Mantech saved 50 percent in labor costs, and can now provision development and test resources in minutes instead of weeks.
The IBM Transformation Story
Leslie Gordon, IBM Vice President of Application and Infrastructure Services Management, presented IBM's own transformation story, becoming the premier "Globally Integrated Enterprise". Based on IBM's 2009 CIO study, CIOs must balance three roles with seemingly contradictory demands:
Make innovations real, be both an insightful visionary but also an able pragmatist
Raise the Return on Investment (ROI) of IT, determine savvy ways to create value but also be ruthless at cutting costs
Expanding the business impact of IT, be a collaborative business leader with the other C-level executives, but also be an inspiring manager for the IT staff.
In this case, IBM drinks its own champagne, using its own solutions to help run its internal operations. In 1997, IBM used over 15,000 applications, but this has been simplified down to 4500 applications today. Thousands of servers were consolidated to Linux on System z mainframes. The applications workloads were categorized as Blue, Bronze, Silver, and Gold to help prioritize the consolidation. IBM's key lessons from all this were:
Gather data at the business unit level, but build the business case from an enterprise view.
Start small and monitor progress continually, run operations concurrently with transformational projects
Address cultural and organizational changes by deploying transformation in waves
I found the client testimonials insightful. It is always good to hear that IBM's solutions work "as advertised" right out of the box.
While clients and IBM executives were in meetings today, in and around the Scottsdale Fairmont resort here in Scottsdale, Arizona, I helped to set up the "Solutions Showcase". There were three stations:
David Ayd and I manned this one, covering storage and server systems. From left to right: a fully-populated 15-module XIV storage system, my laptop running the XIV GUI; two-socket 16-core POWER p770 server, a solid-state drive, PS702 POWER blade, my book Inside System Storage: Volume I, HX5 x86 blade, and four-socket 16-core x3850 M3 server with MAX5 memory extension; David's laptop with various POWER and System x presentations, and our Kaon V-Osk interactive plasma screen display.
Eric Kern manned the Smarter Clouds station. He had live guest images on the IBM Developer and Test cloud, which one the "Best of Interop" award up in Las Vegas this week. I covered IBM's cloud offering in my post [Three Things To Do on the IBM Cloud].
Smarter Data Centers
Ken Schneebeli manned the "Smarter Data Centers" station. He directed people out to the parking lot to see Brian Canney and the Portable Modular Data Center (PMDC). The one here is 8.5 feet by 8.5 feet by 40 feet in size and can be configured and deployed in 12-14 weeks to any location. We can fit any mix of IBM and non-IBM equipment, provided it meets physical dimensions. Want a DS8700 disk system? The PMDC can hold up to 3-frame configurations of the DS8700. Want an eclectic mix of Sun, HP and Dell servers with HDS and EMC disk in your PMDC? IBM can do that too.
After we finished setup, we joined the clients at the "Welcome Reception" on the Lagoon Lawn. The weather was quite pleasant.
Special thanks to Jasdeep Purdhani, Lisa Gates, and Kelly Olson for their help organizing this event.
This week, Tuesday, Wednesday and Thursday, I am at the IBM Dynamic Infrastructure Executive Summit at the beautiful Fairmont Resort in Scottsdale, Arizona. This is a mix of indoor and outdoor meetings, one-on-ones with IBM executives, and main-tent sessions.
The Solutions Showcase will cover the following:
As the bar for performance gets higher and the need to manage, store and analyze massive amounts of information escalates, systems must scale to meet the needs of the business. The latest server and storage technology innovations including: POWER7, eX5, XIV, ProtecTIER, SONAS, and System z Solution Editions.
Smarter Data Centers
Today’s data centers are under extreme power and cooling pressures and space constraints. How can you get more out of your existing facility, while planning for future requirements? IBM energy efficiency consultants will tell you how you can reduce both CAPEX and OPEX costs and plan for future growth with consolidation and virtualization, energy efficient (energy star) equipment and modular data center solutions. Be sure to check out the IBM Portable Modular Data Center (PMDC) that fits in a standard shipping crate!
IBM’s Cloud Computing solutions provide you with flexible, dynamic, secure and cost-efficient delivery choices from pay-per-use (by the hour, week or year) at IBM cloud centers around the world, conditioning your infrastructure to build your own private cloud or out-of-the box cloud solutions that are quick and easy to deploy. Which workloads are the best fit for cloud computing? How do you decide which cloud computing is right for your organization? Cloud experts will talk about the options, give you recommendations based on your business objectives and help you get started.
My colleagues, Harley Puckett (left) and Jack Arnold (right) were highlighted in today's Arizona Daily Star, our local newspaper, as part of an article on IBM's success and leadership in the IT storage industry. At 1400 employees here in Tucson, IBM is Southern Arizona's 36th largest employer.
Highlighted in the article:
DS8700 with the new Easy Tier feature
TS7650 ProtecTIER virtual tape library with data deduplication capability
LTO-5 tape and the new Long Term File System (LTFS)
XIV with the new 2TB drive, for a maximum per-rack usable capacity of 161 TB.
Continuing my discussion of this week's announcements of IBM storage products, I will cover the announcements that double storage capacity per footprint.
Linear Tape Open - Generation 5
IBM announced [LTO-5 drives], the TS2250 half-height and the TS2350 full-height drives, as well as support for LTO-5 drives in its various tape libraries: TS3100, TS3200, and TS3500. The native 1.5TB capacity of the LTO-5 cartridge is nearly double the 800GB capacity of the LTO-4 predecessor. With 2:1 compression, that's 3TB of data per cartridge! Performance-wise, the data transfer rate is 140 MB/sec, about 17 percent improvement over the 120MB/sec of the LTO-4 technology. The TS2250, TS2350, TS3100 and TS3200 now all offer dual-SAS ports for higher availability.
LTO-5 carries forward many of the advancements of past generations. For example, LTO-5 continues the G-2/G-1 "backward compatibility" architecture, which means that the LTO-5 drive can read LTO-3 and LTO-4 cartridges, and can write LTO-4 cartridges. Like the LTO-3 and LTO-4, the same LTO-5 drive can read and write WORM or regular rewriteable cartridges. Like the LTO-4, the LTO-5 offers drive-level data-at-rest encryption. These use a symmetric 256-bit AES key, managed by IBM Tivoli Key Lifecycle Manager (TKLM).
One thing that is new in LTO-5 is the Long Term File System [LTFS] available on the TS2250 and TS2350, which allows you to treat the tape as a hierarchical file system, with files and folders, that you can drag and drop like any other file system.
XIV storage system
IBM [doubles the capacity of the XIV storage system] by supporting 2TB SATA drives. A full 15-module frame can hold up to 161TB of usable capacity. The smallest 6-module system with 2TB can hold up to 55TB of usable capacity. At this time, all of the drives in an XIV must be the same type, so we do not yet allow intermix of 1TB and 2TB in the same frame. The 2TB are more energy efficient, with a full 15-module frame consuming on average 6.7 kVA, compared to 7.8 kVA for the 1TB drives. The performance is roughly the same, so if, for example, your application workload got 3700 IOPS per module with 1TB drives, it will get about the same 3700 IOPS per module with 2TB drives.
The EXN1000 and EXN3000 can now double in capacity with 2TB SATA drives. These can be attached to the N3000 entry-level models, such as the N3400.
DS3000 disk system
The DS3200, DS3300 and DS3400, as well as their related expansion drawers, now supports 2TB SATA drives. This means that a single control unit with three expansion drawers can hold up to 96TB of raw capacity (48 drives).
DS8700 disk system
The DS8700 also now supports 2TB SATA drives, for a maximum raw capacity over 2PB, as well as new 600GB Fibre Channel drives. Now that IBM offers [Easy Tier] functionality, pairing Solid State Drives with slower, energy-efficient SATA disk makes a lot of financial sense.
That's a lot of announcements! As always, feel free to dig into each of the links to learn more about each product.
Now that the US Recession has been declared over, companies are looking to invest in IT again. To help you plan your upcoming investments, here are some upcoming events in April.
SNW Spring 2010, April 12-15
IBM is a Platinum Plus sponsor at this [Storage Networking World event], to be held April 12-15 at the Rosen Shingle Creek Resort in Orlando, Florida. If you are planning to go, here's what you can go look for:
IBM booth at the Solution Center featuring the DS8700 and XIV disk systems, SONAS and the Smart Business Storage Cloud (SBSC), and various Tivoli storage software
IBM kiosk at the Platinum Galleria focusing on storage solutions for SAP and Microsoft environments
IBM Senior Engineer Mark Fleming presenting "Understanding High Availability in the SAN"
IBM sponsored "Expo Lunch" on Tuesday, April 13, featuring Neville Yates, CTO of IBM ProtecTIER, presenting "Data Deduplication -- It's not Magic - It's Math!"
IBM CTO Vincent Hsu presenting "Intelligent Storage: High Performance and Hot Spot Elimination"
IBM Senior Technical Staff Member (STSM) Gordon Arnold presenting "Cloud Storage Security"
One-on-One meetings with IBM executives
I have personally worked with Mark, Neville, Vincent and Gordon, so I am sure they will do a great job in their presentations. Sadly, I won't be there myself, but fellow blogger [Rich Swain from IBM] will be at the event to blog about all the actviities there.
Jim Stallings - General Manager, Global Markets, IBM Systems and Technology Group
Scott Handy - Vice President, WW Marketing, Power Systems, IBM Systems and Technology Group
Dan Galvan - Vice President, Marketing & Strategy, Storage and Networking Systems, IBM Systems and Technology Group
Inna Kuznetsova - Vice President, Marketing and Sales Enablement, Systems Software, IBM Systems and Technology Group
Jeanine Cotter - Vice President, Systems Services, IBM Global Technology Services
The webinar will include client testimonials from various companies as well.
Dynamic Infrastructure Executive Summit, April 27-29
I will be there, at this this 2-and-a-half-day [Executive Summit] in Scottsdale, Arizona, to talk to company executives. Discover how IBM can help you manage your ever-increasing amount of information with an end-to-end, innovative approach to building a dynamic infrastructure. You will learn all of our innovative solutions and find out how you can effectively transform your enterprise for a smarter planet.
“In times of universal deceit, telling the truth will be a revolutionary act.”
-- George Orwell
Well, it has been over two years since I first covered IBM's acquisition of the XIV company. Amazingly, I still see a lot of misperceptions out in the blogosphere, especially those regarding double drive failures for the XIV storage system. Despite various attempts to [explain XIV resiliency] and to [dispel the rumors], there are still competitors making stuff up, putting fear, uncertainty and doubt into the minds of prospective XIV clients.
Clients love the IBM XIV storage system! In this economy, companies are not stupid. Before buying any enterprise-class disk system, they ask the tough questions, run evaluation tests, and all the other due diligence often referred to as "kicking the tires". Here is what some IBM clients have said about their XIV systems:
“3-5 minutes vs. 8-10 hours rebuild time...”
-- satisfied XIV client
“...we tested an entire module failure - all data is re-distributed in under 6 hours...only 3-5% performance degradation during rebuild...”
-- excited XIV client
“Not only did XIV meet our expectations, it greatly exceeded them...”
In this blog post, I hope to set the record straight. It is not my intent to embarrass anyone in particular, so instead will focus on a fact-based approach.
Fact: IBM has sold THOUSANDS of XIV systems
XIV is "proven" technology with thousands of XIV systems in company data centers. And by systems, I mean full disk systems with 6 to 15 modules in a single rack, twelve drives per module. That equates to hundreds of thousands of disk drives in production TODAY, comparable to the number of disk drives studied by [Google], and [Carnegie Mellon University] that I discussed in my blog post [Fleet Cars and Skin Cells].
Fact: To date, no customer has lost data as a result of a Double Drive Failure on XIV storage system
This has always been true, both when XIV was a stand-alone company and since the IBM acquisition two years ago. When examining the resilience of an array to any single or multiple component failures, it's important to understand the architecture and the design of the system and not assume all systems are alike. At it's core, XIV is a grid-based storage system. IBM XIV does not use traditional RAID-5 or RAID-10 method, but instead data is distributed across loosely connected data modules which act as independent building blocks. XIV divides each LUN into 1MB "chunks", and stores two copies of each chunk on separate drives in separate modules. We call this "RAID-X".
Spreading all the data across many drives is not unique to XIV. Many disk systems, including EMC CLARiiON-based V-Max, HP EVA, and Hitachi Data Systems (HDS) USP-V, allow customers to get XIV-like performance by spreading LUNs across multiple RAID ranks. This is known in the industry as "wide-striping". Some vendors use the terms "metavolumes" or "extent pools" to refer to their implementations of wide-striping. Clients have coined their own phrases, such as "stripes across stripes", "plaid stripes", or "RAID 500". It is highly unlikely that an XIV will experience a double drive failure that ultimately requires recovery of files or LUNs, and is substantially less vulnerable to data loss than an EVA, USP-V or V-Max configured in RAID-5. Fellow blogger Keith Stevenson (IBM) compared XIV's RAID-X design to other forms of RAID in his post [RAID in the 21st Centure].
Fact: IBM XIV is designed to minimize the likelihood and impact of a double drive failure
The independent failure of two drives is a rare occurrence. More data has been lost from hash collisions on EMC Centera than from double drive failures on XIV, and hash collisions are also very rare. While the published worst-case time to re-protect from a 1TB drive failure for a fully-configured XIV is 30 minutes, field experience shows XIV regaining full redundancy on average in 12 minutes. That is 40 times less likely than a typical 8-10 hour window for a RAID-5 configuration.
A lot of bad things can happen in those 8-10 hours of traditional RAID rebuild. Performance can be seriously degraded. Other components may be affected, as they share cache, connected to the same backplane or bus, or co-dependent in some other manner. An engineer supporting the customer onsite during a RAID-5 rebuild might pull the wrong drive, thereby causing a double drive failure they were hoping to avoid. Having IBM XIV rebuild in only a few minutes addresses this "human factor".
In his post [XIV drive management], fellow blogger Jim Kelly (IBM) covers a variety of reasons why storage admins feel double drive failures are more than just random chance. XIV avoids load stress normally associated with traditional RAID rebuild by evenly spreading out the workload across all drives. This is known in the industry as "wear-leveling". When the first drive fails, the recovery is spread across the remaining 179 drives, so that each drive only processes about 1 percent of the data. The [Ultrastar A7K1000] 1TB SATA disk drives that IBM uses from HGST have specified 1.2 million hours mean-time-between-failures [MTBF] would average about one drive failing every nine months in a 180-drive XIV system. However, field experience shows that an XIV system will experience, on average, one drive failure per 13 months, comparable to what companies experience with more robust Fibre Channel drives. That's innovative XIV wear-leveling at work!
Fact: In the highly unlikely event that a DDF were to occur, you will have full read/write access to nearly all of your data on the XIV, all but a few GB.
Even though it has NEVER happened in the field, some clients and prospects are curious what a double drive failure on an XIV would look like. First, a critical alert message would be sent to both the client and IBM, and a "union list" is generated, identifying all the chunks in common. The worst case on a 15-module XIV fully loaded with 79TB data is approximately 9000 chunks, or 9GB of data. The remaining 78.991 TB of unaffected data are fully accessible for read or write. Any I/O requests for the chunks in the "union list" will have no response yet, so there is no way for host applications to access outdated information or cause any corruption.
(One blogger compared losing data on the XIV to drilling a hole through the phone book. Mathematically, the drill bit would be only 1/16th of an inch, or 1.60 millimeters for you folks outside the USA. Enough to knock out perhaps one character from a name or phone number on each page. If you have ever seen an actor in the movies look up a phone number in a telephone booth then yank out a page from the phone book, the XIV equivalent would be cutting out 1/8th of a page from an 1100 page phone book. In both cases, all of the rest of the unaffected information is full accessible, and it is easy to identify which information is missing.)
If the second drive failed several minutes after the first drive, the process for full redundancy is already well under way. This means the union list is considerably shorter or completely empty, and substantially fewer chunks are impacted. Contrast this with RAID-5, where being 99 percent complete on the rebuild when the second drive fails is just as catastrophic as having both drives fail simultaneously.
Fact: After a DDF event, the files on these few GB can be identified for recovery.
Once IBM receives notification of a critical event, an IBM engineer immediately connects to the XIV using remote service support method. There is no need to send someone physically onsite, the repair actions can be done remotely. The IBM engineer has tools from HGST to recover, in most cases, all of the data.
Any "union" chunk that the HGST tools are unable to recover will be set to "media error" mode. The IBM engineer can provide the client a list of the XIV LUNs and LBAs that are on the "media error" list. From this list, the client can determine which hosts these LUNs are attached to, and run file scan utility to the file systems that these LUNs represent. Files that get a media error during this scan will be listed as needing recovery. A chunk could contain several small files, or the chunk could be just part of a large file. To minimize time, the scans and recoveries can all be prioritized and performed in parallel across host systems zoned to these LUNs.
As with any file or volume recovery, keep in mind that these might be part of a larger consistency group, and that your recovery procedures should make sense for the applications involved. In any case, you are probably going to be up-and-running in less time with XIV than recovery from a RAID-5 double failure would take, and certainly nowhere near "beyond repair" that other vendors might have you believe.
Fact: This does not mean you can eliminate all Disaster Recovery planning!
To put this in perspective, you are more likely to lose XIV data from an earthquake, hurricane, fire or flood than from a double drive failure. As with any unlikely disaster, it is best to have a disaster recovery plan than to hope it never happens. All disk systems that sit on a single datacenter floor are vulnerable to such disasters.
For mission-critical applications, IBM recommends using disk mirroring capability. IBM XIV storage system offers synchronous and asynchronous mirroring natively, both included at no additional charge.
Well, it's Tuesday again, and that means IBM announcements! Right on the heels of our big storage launch on February 9, today IBM announced some exciting options for its modular disk systems. Let's take a look:
2TB SATA-II drives
That's right, you can now DOUBLE your capacity with 2TB SATA type-II drives on the DS3950, DS4200, DS4700, DS5020, DS5100 and DS5300 disk controllers, as well as the DS4000 EXP420, EXP520, EXP810, EXP5000 and EXP5060 expansion drawers. Here are the Announcement Letters for the [HVEC] and [AAS] ordering systems.
300GB Solid State Drives
IBM also announces 300GB solid state drives (SSD) for the DS5100 and DS5300. These are four times larger than the 73GB drives IBM offered last year, for those workloads that need high read IOPS such as Online Transaction Processing (OLTP) and Enterprise Resource Planning (ERP) applications. Here is the [Announcement Letter].
New N series model N3400
For customers that need less than the minimum 21TB that our IBM Scale-Out Network Attach Storage (SONAS) can provide, IBM offers the new N3400 unified storage disk system, with support for NFS, CIFS, iSCSI and FCP. This is a 2U high 12 drive model that can be expanded up to 136 drives, basically doubling all the stats from last year's N3300 model. Fellow blogger, Rich Swain (IBM), does a great job recapping the speeds and feeds over on his blog [News and Information about IBM N series].
It also appears that the reports and rumors of the death of the DS6800 are premature. Don't believe misleading statements from competitors, such as those found written by fellow blogger BarryB (EMC), aka "the Storage Anarchist", in his latest post [Bring Out Your Dead] showing a cute little tombstone with "Feb 2010" on the bottom. Actually, if he had bothered to read IBM's [Announcement Letter], he would have realized that IBM plans to continue to sell these until June. Of course, IBM will continue to support both new and existing DS6800 customers for many years to come.
Technically, BarryB does not make any factually incorrect statements for me to correct on his blog. The idea that a product is "dead" is, of course, just opinion, and competitors poke fun at each others' announcements every day. One could argue that the EMC V-Max was "dead" after the ITG whitepaper [Cost/Benefit Case for IBM XIV Storage System - Comparing Costs for IBM XIV and EMC V-Max Systems] demonstrated that the IBM XIV cost 63 percent less than a comparable EMC V-Max over the life of three years total cost of ownership (TCO) back in July 2009. The comparison was made with data from clients in a variety of industries including manufacturing, health care, life sciences, telecommunications, financial services, and the public sector. This could explain why so many EMC customers are buying or investigating the IBM XIV and the rest of the IBM storage portfolio.
Continuing my drawn out coverage of IBM's big storage launch of February 9, today I'll cover the IBM System Storage TS7680 ProtecTIER data deduplication gateway for System z.
On the host side, TS7680 connects to mainframe systems running z/OS or z/VM over FICON attachment, emulating an automated tape library with 3592-J1A devices. The TS7680 includes two controllers that emulate the 3592 C06 model, with 4 FICON ports each. Each controller emulates up to 128 virtual 3592 tape drives, for a total of 256 virtual drives per TS7680 system. The mainframe sees up to 1 million virtual tape cartridges, up to 100GB raw capacity each, before compression. For z/OS, the automated library has full SMS Tape and Integrated Library Management capability that you would expect.
Inside, the two control units are both connected to a redundant pair cluster of ProtecTIER engines running the HyperFactor deduplication algorithm that is able to process the deduplication inline, as data is ingested, rather than post-process that other deduplication solutions use. These engines are similar to the TS7650 gateway machines for distributed systems.
On the back end, these ProtecTIER deduplication engines are then connected to external disk, up to 1PB. If you get 25x data deduplication ratio on your data, that would be 25PB of mainframe data stored on only 1PB of physical disk. The disk can be any disk supported by ProtecTIER over FCP protocol, not just the IBM System Storage DS8000, but also the IBM DS4000, DS5000 or IBM XIV storage system, various models of EMC and HDS, and of course the IBM SAN Volume Controller (SVC) with all of its supported disk systems.
Continuing my coverage of the Data Center Conference, held Dec 1-4 in Las Vegas, an analyst presented the challenges of managing the rapid growth in storage capacity. Administrators ability to manage storage is not keeping up with the growth. His recommendations:
Aim to just meet but not exceed service level agreements (SLAs)
Revisit past IT decisions. This includes evaluating your SAN to NAS ratio.
Embrace new technologies when they are effective, this includes cloud storage, solid state drives, and interconnect technologies like FCoCEE.
Follow vendor management best practices, update your vendor "short list".
A survey of the audience found:
20 percent have a single external storage vendor
39 percent have two external storage vendors
18 percent have three external storage vendors
23 percent have four or more external storage vendors
Throughout the industry, storage vendors are following IBM's example of using commodity hardware parts. This is because custom ASICs are expensive, and changes take a minimum of three months development time. Software-based implementations can be updated more quickly.
In terms of technologies deployed of SAN, NAS, Compliance Archive (such as the IBM Information Archive), and Virtual Tape Library (VTL) such as the IBM TS7650 ProtecTIER data deduplications solution, here was the survey of the audience:
8 percent: SAN only
14 percent: SAN and NAS
23 percent: SAN, NAS and Compliance Archive
9 percent: SAN and VTL
14 percent: SAN, NAS and VTL
32 percent: SAN, NAS, Compliance Archive and VTL
Cost reduction techniques including thin provisioning, compression, data deduplication, Quality of Service tiers, and archiving. To reduce power and cooling requirements, switch from FC to SATA disk wherever possible, and move storage out of the data center, such as on tape cartridges or cloud storage.
For emerging technologies, the following survey:
16 percent have already implemented a new emerging technology (IBM XIV, Pillar, 3PAR, etc.)
30 percent plan to do so in 12-24 months
4 percent plan to do so in 24-48 months
50 percent have no plans, and will continue to stick with traditional storage technologies
As for adopting Cloud storage, here was the survey:
14 percent already have
31 percent plan to use Cloud storage in 12-24 months
13 percent plan to use Cloud storage in 24-48 months
42 percent have no plans to adopt Cloud storage
My take-away from this is that many companies are still "exploring" into different options available to them. Fortunately, IBM offers a broad portfolio of complete end-to-end solutions to make acquiring the right mix of technologies that are optimized for your workloads possible.
Well, it's Tuesday again, and we have more IBM announcements.
XIV asynchronous mirror
For those not using XIV behind SAN Volume Controller, [XIV now offers native asynchronous mirroring] support to another XIV far, far away. Unlike other disk systems that are limited to two or three sites, an XIV can mirror to up to 15 other sites. The mirroring can be at the individual volume, or a consistency group of multiple volumes. Each mirror pair can have its own recovery point objective (RPO). For example, a consistency group of mission critical application data might be given an RPO of 30 seconds, but less important data might be given an RPO of 20 minutes. This allows the XIV to prioritize packets it sends across the network.
As with XIV synchronous mirror, this new asynchronous mirror feature can send the data over either its
Fibre Channel ports (via FCIP) or its Ethernet ports.
The IBM System Storage SAN384B and SAN768B directors now offer [two new blades!]
A 24-port FCoCEE blade where each port can handle 10Gb convergence enhanced Ethernet (CEE). CEE can be used to transmit Fibre Channel, TCP/IP, iSCSI and other Ethernet protocols. This connect directly to server's converged network adapter (CNA) cards.
A 24-port mixed blade, with 12 FC ports (1Gbps, 2Ggbs, 4Gbps, 8Gbps), 10 Ethernet ports (1GbE) and 2 Ethernet ports (10GbE). This would connect to traditional server NIC, TOE and HBA cards as well as traditional NAS, iSCSI and FC based storage devices.
IBM also announced the IBM System Storage [SAN06B-R Fibre Channel router]. This has 16 FC ports (1Gbps up to 8Gbps) and six Ethernet ports (1GbE), with support for both FC routing as well as FCIP extended distance support.
With the holiday season coming up at the end of the year, now is a great time to ask Santa for a new shiny pair of XIV systems, and some extra networking gear to connect them.
Well, it's Tuesday again, but this time, today we had our third big storage launch of 2009! A lot got announced today as part of IBM's big "Dynamic Infrastructure" marketing campaign. I will just focus on the
disk-related announcements today:
IBM System Storage DS8700
IBM adds a new model to its DS8000 series with the
[IBM System Storage DS8700]. Earlier this month, fellow blogger and arch-nemesis Barry Burke from EMC posted [R.I.P DS8300] on this mistaken assumption that the new DS8700 meant that DS8300 was going away, or that anyone who bought a DS8300 recently would be out of luck. Obviously, I could not respond until today's announcement, as the last thing I want to do is lose my job disclosing confidential information. BarryB is wrong on both counts:
IBM will continue to sell the DS8100 and DS8300, in addition to the new DS8700.
Clients can upgrade their existing DS8100 or DS8300 systems to DS8700.
BarryB's latest post [What's In a Name - DS8700] is fair game, given all the fun and ridicule everyone had at his expense over EMC's "V-Max" name.
So the DS8700 is new hardware with only 4 percent new software. On the hardware side, it uses faster POWER6 processors instead of POWER5+, has faster PCI-e buses instead of the RIO-G loops, and faster four-port device adapters (DAs) for added bandwidth between cache and drives. The DS8700 can be ordered as a single-frame dual 2-way that supports up to 128 drives and 128GB of cache, or as a dual 4-way, consisting of one primary frame, and up to four expansion frames, with up to 384GB of cache and 1024 drives.
Not mentioned explicitly in the announcements were the things the DS8700 does not support:
ESCON attachment - Now that FICON is well-established for the mainframe market, there is no need to support the slower, bulkier ESCON options. This greatly reduced testing effort. The 2-way DS8700 can support up to 16 four-port FICON/FCP host adapters, and the 4-way can support up to 32 host adapters, for a maximum of 128 ports. The FICON/FCP host adapter ports can auto-negotiate between 4Gbps, 2Gbps and 1Gbps as needed.
LPAR mode - When IBM and HDS introduced LPAR mode back in 2004, it sounded like a great idea the engineers came up with. Most other major vendors followed our lead to offer similar "partitioning". However, it turned out to be what we call in the storage biz a "selling apple" not a "buying apple". In other words, something the salesman can offer as a differentiating feature, but that few clients actually use. It turned out that supporting both LPAR and non-LPAR modes merely doubled the testing effort, so IBM got rid of it for the DS8700.
Update: I have been reminded that both IBM and HDS delivered LPAR mode within a month of each other back in 2004, so it was wrong for me to imply that HDS followed IBM's lead when obviously development happened in both companies for the most part concurrently prior to that. EMC was late to the "partition" party, but who's keeping track?
Initial performance tests show up to 50 percent improvement for random workloads, and up to 150 percent improvement for sequential workloads, and up to 60 percent improvement in background data movement for FlashCopy functions. The results varied slightly between Fixed Block (FB) LUNs and Count-Key-Data (CKD) volumes, and I hope to see some SPC-1 and SPC-2 benchmark numbers published soon.
The DS8700 is compatible for Metro Mirror, Global Mirror, and Metro/Global Mirror with the rest of the DS8000 series, as well as the ESS model 750, ESS model 800 and DS6000 series.
New 600GB FC and FDE drives
IBM now offers [600GB drives] for the DS4700 and DS5020 disk systems, as well as the EXP520 and EXP810 expansion drawers. In each case, we are able to pack up to 16 drives into a 3U enclosure.
Personally, I think the DS5020 should have been given a DS4xxx designation, as it resembles the DS4700
more than the other models of the DS5000 series. Back in 2006-2007, I was the marketing strategist for IBM System Storage product line, and part of my job involved all of the meetings to name or rename products. Mostly I gave reasons why products should NOT be renamed, and why it was important to name the products correctly at the beginning.
IBM System Storage SAN Volume Controller hardware and software
Fellow IBM master inventory Barry Whyte has been covering the latest on the [SVC 2145-CF8 hardware]. IBM put out a press release last week on this, and today is the formal announcement with prices and details. Barry's latest post
[SVC CF8 hardware and SSD in depth] covers just part of the entire
The other part of the announcement was the [SVC 5.1 software] which can be loaded
on earlier SVC models 8F2, 8F4, and 8G4 to gain better performance and functionality.
To avoid confusion on what is hardware machine type/model (2145-CF8 or 2145-8A4) and what is software program (5639-VC5 or 5639-VW2), IBM has introduced two new [Solution Offering Identifiers]:
5465-028 Standard SAN Volume Controller
5465-029 Entry Edition SAN Volume Controller
The latter is designed for smaller deployments, supports only a single SVC node-pair managing up to
150 disk drives, available in Raven Black or Flamingo Pink.
EXN3000 and EXP5060 Expansion Drawers
IBM offers the [EXN3000 for the IBM N series]. These expansion drawers can pack 24 drives in a 4U enclosure. The drives can either be all-SAS, or all-SATA, supporting 300GB, 450GB, 500GB and 1TB size capacity drives.
The [EXP5060 for the IBM DS5000 series] is a high-density expansion drawer that can pack up to 60 drives into a 4U enclosure. A DS5100 or DS5300
can handle up to eight of these expansion drawers, for a total of 480 drives.
Pre-installed with Tivoli Storage Productivity Center Basic Edition. Basic Edition can be upgraded with license keys to support Data, Disk and Standard Edition to extend support and functionality to report and manage XIV, N series, and non-IBM disk systems.
Pre-installed with Tivoli Key Lifecycle Manager (TKLM). This can be used to manage the Full Disk Encryption (FDE) encryption-capable disk drives in the DS8000 and DS5000, as well as LTO and TS1100 series tape drives.
IBM Tivoli Storage FlashCopy Manager v2.1
The [IBM Tivoli Storage FlashCopy Manager V2.1] replaces two products in one. IBM used
to offer IBM Tivoli Storage Manager for Copy Services (TSM for CS) that protected Windows application data, and IBM Tivoli Storage Manager for Advanced Copy Services (TSM for ACS) that protected AIX application data.
The new product has some excellent advantages. FlashCopy Manager offers application-aware backup of LUNs containing SAP, Oracle, DB2, SQL server and Microsoft Exchange data. It can support IBM DS8000, SVC and XIV point-in-time copy functions, as well as the Volume Shadow Copy Services (VSS) interfaces of the IBM DS5000, DS4000 and DS3000 series disk systems. It is priced by the amount of TB you copy, not on the speed or number of CPU processors inside the server.
Don't let the name fool you. IBM FlashCopy Manager does not require that you use Tivoli Storage Manager (TSM) as your backup product. You can run IBM FlashCopy Manager on its own, and it will manage your FlashCopy target versions on disk, and these can be backed up to tape or another disk using any backup product. However, if you are lucky enough to also be using TSM, then there is optional integration that allows TSM to manage the target copies, move them to tape, inventory them in its DB2 database, and provide complete reporting.
Yup, that's a lot to announce in one day. And this was just the disk-related portion of the launch!