Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is a Master Inventor and Senior IT Specialist for the IBM System Storage product line at the
IBM Executive Briefing Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2011, Tony celebrated his 25th year anniversary with IBM Storage on the same day as the IBM's Centennial. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services. You can also follow him on Twitter @az990tony.
(Short URL for this blog: ibm.co/Pearson
From New York, Rolf went to London, Paris, Madrid, Morocco, Cairo, South Africa, Bangkok Thailand, Malaysia, Singapore, New Zealand, Australia, and then back to United States. I was hoping to run into him while I was in Australia and New Zealand last month, but our schedules did not line up.
Travelingwithout baggage is more than just a convenience, it is a metaphor for the philosophy that we should keep only what we need, and leave behind what we don't. This was the approach taken by IBM in the design of the IBM Storwize V7000 midrange disk system.
The IBM Storwize V7000 disk system consists of 2U enclosures. Controller enclosures have dual-controllers and drives. Expansion enclosures have just drives. Enclosures can have either 24 smaller form factor (SFF) 2.5-inch drives, or twelve larger 3.5-inch drives. A controller enclosure can be connected up to nine expansion enclosures.
The drives are all connected via 6 Gbps SAS, and come in a variety of speeds and sizes: 300GB Solid-State Drive (SSD); 300GB/450GB/600GB high-speed 10K RPM; and 2TB low-speed 7200 RPM drives. The 12-bay enclosures can be intermixed with 24-bay enclosures on the same system, and within an enclosure different speeds and sizes can be intermixed. A half-rack system (20U) could hold as much as 480TB of raw disk capacity.
This new system, freshly designed entirely within IBM, competes directly against systems that carry a lot of baggage, including the HDS AMS, HP EVA, an EMC CLARiiON CX4 systems. Instead, we decided to keep the what we wanted from our other successful IBM products.
Inspired by our successful XIV storage system, IBM has developed a web-based GUI that focuses on ease-of-use. This GUI uses the latest HTML5 and dojo widgets to provide an incredible user experience.
Borrowed from our IBM DS8000 high-end disk systems, state-of-the-art device adapters provide 6 Gbps SAS connectivity with a variety of RAID levels: 0, 1, 5, 6, and 10.
From our SAN Volume Controller, the embedded [ SVC 6.1 firmware] provides all of the features and functions normally associated with enterprise-class systems, including Easy Tier sub-LUN automated tiering between Solid-State Drives and Spinning disk, thin provisioning, external disk virtualization, point-in-time FlashCopy, disk mirroring, built-in migration capability, and long-distance synchronous and asynchronous replication.
Finally, the various "internal NDA" that kept me from publishing this sooner have expired, so now I have the long-awaited [Inside System Storage: Volume II], documenting IBM's transformation in its storage strategy, including behind-the-scenes commentary about IBM's acquisitions of XIV and Diligent. Available initially in paperback form. I am still working on the hard cover and eBook editions.
For those who have not yet read my first book, Inside System Storage: Volume I, it is still available from my publisher Lulu, in [hard cover], [paperback] and [eBook] editions.
IBM System Storage DS8800
A lesson IBM learned long ago was not to make radical changes to high-end disk systems, as clients who run mission-critical applications are more concerned about reliability, availability and serviceability than they are performance or functionality. Shipping any product before it was ready meant painfully having to fix the problems in the field instead.
(EMC apparently is learning this same lesson now with their VMAX disk system. Their Engenuity code from Symmetrix DMX4 was ported over to new CLARiiON-based hardware. With several hundred boxes in the field, they have already racked up over 150 severity 1 problems, roughly half of these resulted in data loss or unavailability issues. For the sake of our mutual clients that have both IBM servers and EMC disk, I hope they get their act together soon.)
To avoid this, IBM made incremental changes to the successful design and architecture of its predecessors. The new DS8800 shares 85 percent of the stable microcode from the DS8700 system. Functions like Metro Mirror, Global Mirror, and Metro/Global Mirror, are compatible with all of the previous models of the DS8000 series, as well as previous models of the IBM Enterprise Storage Server (ESS) line.
The previous models of DS8000 series were designed to take in cold air from both front and back, and route the hot air out the top, known as chimney design. However, many companies are re-arranging their data centers into separate cold aisles and hot aisles. The new DS8800 has front-to-back cooling to help accommodate this design.
My colleague Curtis Neal would call the rest of this a "BFD" announcement, which of course stands for "Bigger, Faster and Denser". The new DS8800 scales-up to more drives than its DS8700 predecessor, and can scale-out from a single-frame 2-way system to a multi-frame 4-way system. IBM has upgraded to faster 5GHz POWER6+ processors, with dual-core 8 Gbps FC and FICON host adapters, 8 Gbps device adapters, and 6 Gbps SAS connectivity to smaller form factor (SFF) 2.5-inch SAS drives. IBM Easy Tier will provide sub-LUN automated tiering between Solid-State Drives and spinning disk. The denser packaging with SFF drives means that we can pack over 1000 drives in only three frames, compared to five frames required for the DS8700.
The [IBM System Storage SAN Volume Controller] software release v6.1 brings Easy Tier sub-LUN automated tiering to the rest of the world. IBM Easy Tier moves the hottest, most active extents up to Solid-State Drives (SSD) and moves the coldest, least active down to spinning disk. This works whether the SSD is inside the SVC 2145-CF8 nodes, or in the managed disk pool.
Tired of waiting for EMC to finally deliver FAST v2 for your VMAX? It has been 18 months since they first announced that someday they would have sub-LUN automatic tiering. What is taking them so long? Why not virtualize your VMAX with SVC, and you can have it sooner!
SVC 6.1 also upgrades to a sexy new web-based GUI, which like the one for the IBM Storwize V7000, is based on the latest HTML5 and dojo widget standards. Inspired by the popular GUI from the IBM XIV Storage System, this GUI has greatly improved ease-of-use.
Well, I'm back safely from my tour of Asia. I am glad to report that Tokyo, Beijing and Kuala Lumpur are pretty much how I remember them from the last time I was there in each city. I have since been fighting jet lag by watching the last thirteen episodes of LOST season 6 and the series finale.
Recently, I have started seeing a lot of buzz on the term "Storage Federation". The concept is not new, but rather based on the work in database federation, first introduced in 1985 by [A federated architecture for information management] by Heimbigner and McLeod. For those not familiar with database federation, you can take several independent autonomous databases, and treat them as one big federated system. For example, this would allow you to issue a single query and get results across all the databases in the federated system. The advantage is that it is often easier to federate several disparate heterogeneous databases than to merge them into a single database. [IBM Infosphere Federation Server] is a market leader in this space, with the capability to federate DB2, Oracle and SQL Server databases.
Storage expansion: You want to increase the storage capacity of an existing storage system that cannot accommodate the total amount of capacity desired. Storage Federation allows you to add additional storage capacity by adding a whole new system.
Storage migration: You want to migrate from an aging storage system to a new one. Storage Federation allows the joining of the two systems and the evacuation from storage resources on the first onto the second and then the first system is removed.
Safe system upgrades: System upgrades can be problematic for a number of reasons. Storage Federation allows a system to be removed from the federation and be re-inserted again after the successful completion of the upgrade.
Load balancing: Similar to storage expansion, but on the performance axis, you might want to add additional storage systems to a Storage Federation in order to spread the workload across multiple systems.
Storage tiering: In a similar light, storage systems in a Storage Federation could have different capacity/performance ratios that you could use for tiering data. This is similar to the idea of dynamically re-striping data across the disk drives within a single storage system, such as with 3PAR's Dynamic Optimization software, but extends the concept to cross storage system boundaries.
To some extent, IBM SAN Volume Controller (SVC), XIV, Scale-Out NAS (SONAS), and Information Archive (IA) offer most, if not all, of these capabilities. EMC claims its VPLEX will be able to offer storage federation, but only with other VPLEX clusters, which brings up a good question. What about heterogenous storage federation? Before anyone accuses me of throwing stones at glass houses, let's take a look at each IBM solution:
IBM SAN Volume Controller
The IBM SAN Volume Controller has been doing storage federation since 2003. Not only can IBM SAN Volume Controller bring together storage from a variety of heterogenous storage, the SVC cluster itself can be a mix of different hardware models. You can have a 2145-8A4 node pair, 2145-8G4 node pair, and the new 2145-CF8 node pair, all combined together into a single SVC cluster. Upgrading SVC hardware nodes in an SVC cluster is always non-disruptive.
IBM XIV storage system
The IBM XIV has two kinds of independent modules. Data modules have processor, cache and 12 disks. Interface modules are data modules with additional processor, FC and Ethernet (iSCSI) adapters. Because these two modules play different roles in an XIV "colony", that number of each type is predetermined. Entry-level six-module systems have 2 interface and 4 data modules. Full 15-module systems have 6 interface and 9 data modules. Individual modules can be added or removed non-disruptively in an XIV.
IBM Scale-Out NAS
The SONAS is comprised of three kinds of nodes that work together in concert. A management node, one or more interface nodes, and two or more storage nodes. The storage nodes are paired to manage up to 240 nodes in a storage pod. Individual interface or data nodes can be added or removed non-disruptively in the SONAS. The underlying technology, the General Parallel File System, has been doing storage federation since 1996 for some of the largest top 500 supercomputers in the world.
IBM Information Archive (IA)
For the IA, there are 1, 2 or 3 nodes, which manages a set of collections. A collection can either be file-based using industry-standard NAS protocols, or object-based using the popular System Storage™ Archive Manager (SSAM) interface. Normally, you have as many collections as you have nodes, but nodes are powerful enough to manage two collections to provide N-1 availability. This allows a node to be removed, and a new node added into the IA "colony", in a non-disruptive manner.
Even in an ant colony, there are only a few types of ants, with typically one queen, several males, and lots of workers. But all the ants are red. You don't see colonies that mix between different species of ants. For databases, federation was a way to avoid the much harder task of merging databases from different platforms. For storage, I am surprised people have latched on to the term "federation", given our mixed results in the other "federations" we have formed, which I have conveniently (IMHO) ranked from least effective to most effective:
The Union of Soviet Socialist Republics (USSR)
My father used to say, "If the Soviet Union were in charge of the Sahara desert, they would run out of sand in 50 years." The [Soviet Union] actually lasted 68 years, from 1922 to 1991.
The United Nations (UN)
After the previous League of Nations failed, the UN was formed in 1945 to facilitate cooperation in international law, international security, economic development, social progress, human rights, and the achieving of world peace by stopping wars between countries, and to provide a platform for dialogue.
The European Union (EU)
With the collapse of the Greek economy, and the [rapid growth of debt] in the UK, Spain and France, there are concerns that the EU might not last past 2020.
The United States of America (USA)
My own country is a federation of states, each with its own government. California's financial crisis was compared to the one in Greece. My own state of Arizona is under boycott from other states because of its recent [immigration law]. However, I think the US has managed better than the EU because it has evolved over the past 200 years.
The Organization of the Petroleum Exporting Countries [OPEC]
Technically, OPEC is not a federation of cooperating countries, but rather a cartel of competing countries that have agreed on total industry output of oil to increase individual members' profits. Note that it was a non-OPEC company, BP, that could not "control their output" in what has now become the worst oil spill in US history. OPEC was formed in 1960, and is expected to collapse sometime around 2030 when the world's oil reserves run out. Matt Savinar has a nice article on [Life After the Oil Crash].
United Federation of Planets
The [Federation] fictitiously described in the Star Trek series appears to work well, an optimistic view of what federations could become if you let them evolve long enough.
Given the mixed results with "federation", I think I will avoid using the term for storage, and stick to the original term "scale-out architecture".
Here I am, day 11 of a 17-day business trip, on my last leg of the trip this week, in Kuala Lumpur in Malaysia. I have been flooded with requests to give my take on EMC's latest re-interpretation of storage virtualization, VPLEX.
I'll leave it to my fellow IBM master inventor Barry Whyte to cover the detailed technical side-by-side comparison. Instead, I will focus on the business side of things, using Simon Sinek's Why-How-What sequence. Here is a [TED video] from Garr Reynold's post
[The importance of starting from Why].
Let's start with the problem we are trying to solve.
Problem: migration from old gear to new gear, old technology to new technology, from one vendor to another vendor, is disruptive, time-consuming and painful.
Given that IT storage is typically replaced every 3-5 years, then pretty much every company with an internal IT department has this problem, the exception being those companies that don't last that long, and those that use public cloud solutions. IT storage can be expensive, so companies would like their new purchases to be fully utilized on day 1, and be completely empty on day 1500 when the lease expires. I have spoken to clients who have spent 6-9 months planning for the replacement or removal of a storage array.
A solution to make the data migration non-disruptive would benefit the clients (make it easier for their IT staff to keep their data center modern and current) as well as the vendors (reduce the obstacle of selling and deploying new features and functions). Storage virtualization can be employed to help solve this problem. I define virtualization as "technology that makes one set of resources look and feel like a different set of resources, preferably with more desirable characteristics.". By making different storage resources, old and new, look and feel like a single type of resource, migration can be performed without disrupting applications.
Before VPLEX, here is a breakdown of each solution:
Non-disruptive tech refresh, and a unified platform to provide management and functionality across heterogeneous storage.
Non-disruptive tech refresh, and a unified platform to provide management and functionality between internal tier-1 HDS storage, and external tier-2 heterogeneous storage.
Non-disruptive tech refresh, with unified multi-pathing driver that allows host attachment of heterogeneous storage.
New in-band storage virtualization device
Add in-band storage virtualization to existing storage array
New out-of-band storage virtualization device with new "smart" SAN switches
SAN Volume Controller
HDS USP-V and USP-VM
For IBM, the motivation was clear: Protect customers existing investment in older storage arrays and introduce new IBM storage with a solution that allows both to be managed with a single set of interfaces and provide a common set of functionality, improving capacity utilization and availability. IBM SAN Volume Controller eliminated vendor lock-in, providing clients choice in multi-pathing driver, and allowing any-to-any migration and copy services. For example, IBM SVC can be used to help migrate data from an old HDS USP-V to a new HDS USP-V.
With EMC, however, the motivation appeared to protect software revenues from their PowerPath multi-pathing driver, TimeFinder and SRDF copy services. Back in 2005, when EMC Invista was first announced, these three software represented 60 percent of EMC's bottom-line profit. (Ok, I made that last part up, but you get my point! EMC charges a lot for these.)
Back in 2006, fellow blogger Chuck Hollis (EMC) suggested that SVC was just a [bump in the wire] which could not possibly improve performance of existing disk arrays. IBM showed clients that putting cache(SVC) in front of other cache(back end devices) does indeed improve performance, in the same way that multi-core processors successfully use L1/L2/L3 cache. Now, EMC is claiming their cache-based VPLEX improves performance of back-end disk. My how EMC's story has changed!
So now, EMC announces VPLEX, which sports a blend of SVC-like and Invista-like characteristics. Based on blogs, tweets and publicly available materials I found on EMC's website, I have been able to determine the following comparison table. (Of course, VPLEX is not yet generally available, so what is eventually delivered may differ.)
Scalable, 1 to 4 node-pairs
One size fits all, single pair of CPCs
SVC-like, 1 to 4 director-pairs
Works with any SAN switches or directors
Required special "smart" switches (vendor lock-in)
SVC-like, works with any SAN switches or directors
Broad selection of IBM Subsystem Device Driver (SDD) offered at no additional charge, as well as OS-native drivers Windows MPIO, AIX MPIO, Solaris MPxIO, HP-UX PV-Links, VMware MPP, Linux DM-MP, and comercial third-party driver Symantec DMP.
Limited selection, with focus on priced PowerPath driver
Invista-like, PowerPath and Windows MPIO
Read cache, and choice of fast-write or write-through cache, offering the ability to improve performance.
No cache, Split-Path architecture cracked open Fibre Channel packets in flight, delayed every IO by 20 nanoseconds, and redirected modified packets to the appropriate physical device.
SVC-like, Read and write-through cache, offering the ability to improve performance.
Space-Efficient Point-in-Time copies
SVC FlashCopy supports up to 256 space-efficient targets, copies of copies, read-only or writeable, and incremental persistent pairs.
Like Invista, No
Remote distance mirror
Choice of SVC Metro Mirror (synchronous up to 300km) and Global Mirror (asynchronous), or use the functionality of the back-end storage arrays
No native support, use functionality of back-end storage arrays, or purchase separate product called EMC RecoverPoint to cover this lack of functionality
Limited synchronous remote-distance mirror within VPLEX (up to 100km only), no native asynchronous support, use functionality of back-end storage arrays
Provides thin provisioning to devices that don't offer this natively
Like Invista, No
SVC Split-Cluster allows concurrent read/write access of data to be accessed from hosts at two different locations several miles apart
I don't think so
PLEX-Metro, similar in concept but implemented differently
Non-disruptive tech refresh
Can upgrade or replace storage arrays, SAN switches, and even the SVC nodes software AND hardware themselves, non-disruptively
Tech refresh for storage arrays, but not for Invista CPCs
Tech refresh of back end devices, and upgrade of VPLEX software, non-disruptively. Not clear if VPLEX engines themselves can be upgraded non-disruptively like the SVC.
Heterogeneous Storage Support
Broad support of over 140 different storage models from all major vendors, including all CLARiiON, Symmetrix and VMAX from EMC, and storage from many smaller startups you may not have heard of
Invista-like. VPLEX claims to support a variety of arrays from a variety of vendors, but as far as I can find, only DS8000 supported from the list of IBM devices. Fellow blogger Barry Burke (EMC) suggests [putting SVC between VPLEX and third party storage devices] to get the heterogeneous coverage most companies demand.
Back-end storage requirement
Must define quorum disks on any IBM or non-IBM back end storage array. SVC can run entirely on non-IBM storage arrays
HP SVSP-like, requires at least one EMC storage array to hold metadata
SVC 2145-CF8 model supports up to four solid-state drives (SSD) per node that can treated as managed disk to store end-user data
Invista-like. VPLEX has an internal 30GB SSD, but this is used only for operating system and logs, not for end-user data.
In-band virtualization solutions from IBM and HDS dominate the market. Being able to migrate data from old devices to new ones non-disruptively turned out to be only the [tip of the iceberg] of benefits from storage virtualization. In today's highly virtualized server environment, being able to non-disruptively migrate data comes in handy all the time. SVC is one of the best storage solutions for VMware, Hyper-V, XEN and PowerVM environments. EMC watched and learned in the shadows, taking notes of what people like about the SVC, and decided to follow IBM's time-tested leadership to provide a similar offering.
EMC re-invented the wheel, and it is round. On a scale from Invista (zero) to SVC (ten), I give EMC's new VPLEX a six.
Continuing my drawn out coverage of IBM's big storage launch of February 9, today I'll cover the IBM System Storage TS7680 ProtecTIER data deduplication gateway for System z.
On the host side, TS7680 connects to mainframe systems running z/OS or z/VM over FICON attachment, emulating an automated tape library with 3592-J1A devices. The TS7680 includes two controllers that emulate the 3592 C06 model, with 4 FICON ports each. Each controller emulates up to 128 virtual 3592 tape drives, for a total of 256 virtual drives per TS7680 system. The mainframe sees up to 1 million virtual tape cartridges, up to 100GB raw capacity each, before compression. For z/OS, the automated library has full SMS Tape and Integrated Library Management capability that you would expect.
Inside, the two control units are both connected to a redundant pair cluster of ProtecTIER engines running the HyperFactor deduplication algorithm that is able to process the deduplication inline, as data is ingested, rather than post-process that other deduplication solutions use. These engines are similar to the TS7650 gateway machines for distributed systems.
On the back end, these ProtecTIER deduplication engines are then connected to external disk, up to 1PB. If you get 25x data deduplication ratio on your data, that would be 25PB of mainframe data stored on only 1PB of physical disk. The disk can be any disk supported by ProtecTIER over FCP protocol, not just the IBM System Storage DS8000, but also the IBM DS4000, DS5000 or IBM XIV storage system, various models of EMC and HDS, and of course the IBM SAN Volume Controller (SVC) with all of its supported disk systems.
Well, it's Tuesday again, but this time, today we had our third big storage launch of 2009! A lot got announced today as part of IBM's big "Dynamic Infrastructure" marketing campaign. I will just focus on the
disk-related announcements today:
IBM System Storage DS8700
IBM adds a new model to its DS8000 series with the
[IBM System Storage DS8700]. Earlier this month, fellow blogger and arch-nemesis Barry Burke from EMC posted [R.I.P DS8300] on this mistaken assumption that the new DS8700 meant that DS8300 was going away, or that anyone who bought a DS8300 recently would be out of luck. Obviously, I could not respond until today's announcement, as the last thing I want to do is lose my job disclosing confidential information. BarryB is wrong on both counts:
IBM will continue to sell the DS8100 and DS8300, in addition to the new DS8700.
Clients can upgrade their existing DS8100 or DS8300 systems to DS8700.
BarryB's latest post [What's In a Name - DS8700] is fair game, given all the fun and ridicule everyone had at his expense over EMC's "V-Max" name.
So the DS8700 is new hardware with only 4 percent new software. On the hardware side, it uses faster POWER6 processors instead of POWER5+, has faster PCI-e buses instead of the RIO-G loops, and faster four-port device adapters (DAs) for added bandwidth between cache and drives. The DS8700 can be ordered as a single-frame dual 2-way that supports up to 128 drives and 128GB of cache, or as a dual 4-way, consisting of one primary frame, and up to four expansion frames, with up to 384GB of cache and 1024 drives.
Not mentioned explicitly in the announcements were the things the DS8700 does not support:
ESCON attachment - Now that FICON is well-established for the mainframe market, there is no need to support the slower, bulkier ESCON options. This greatly reduced testing effort. The 2-way DS8700 can support up to 16 four-port FICON/FCP host adapters, and the 4-way can support up to 32 host adapters, for a maximum of 128 ports. The FICON/FCP host adapter ports can auto-negotiate between 4Gbps, 2Gbps and 1Gbps as needed.
LPAR mode - When IBM and HDS introduced LPAR mode back in 2004, it sounded like a great idea the engineers came up with. Most other major vendors followed our lead to offer similar "partitioning". However, it turned out to be what we call in the storage biz a "selling apple" not a "buying apple". In other words, something the salesman can offer as a differentiating feature, but that few clients actually use. It turned out that supporting both LPAR and non-LPAR modes merely doubled the testing effort, so IBM got rid of it for the DS8700.
Update: I have been reminded that both IBM and HDS delivered LPAR mode within a month of each other back in 2004, so it was wrong for me to imply that HDS followed IBM's lead when obviously development happened in both companies for the most part concurrently prior to that. EMC was late to the "partition" party, but who's keeping track?
Initial performance tests show up to 50 percent improvement for random workloads, and up to 150 percent improvement for sequential workloads, and up to 60 percent improvement in background data movement for FlashCopy functions. The results varied slightly between Fixed Block (FB) LUNs and Count-Key-Data (CKD) volumes, and I hope to see some SPC-1 and SPC-2 benchmark numbers published soon.
The DS8700 is compatible for Metro Mirror, Global Mirror, and Metro/Global Mirror with the rest of the DS8000 series, as well as the ESS model 750, ESS model 800 and DS6000 series.
New 600GB FC and FDE drives
IBM now offers [600GB drives] for the DS4700 and DS5020 disk systems, as well as the EXP520 and EXP810 expansion drawers. In each case, we are able to pack up to 16 drives into a 3U enclosure.
Personally, I think the DS5020 should have been given a DS4xxx designation, as it resembles the DS4700
more than the other models of the DS5000 series. Back in 2006-2007, I was the marketing strategist for IBM System Storage product line, and part of my job involved all of the meetings to name or rename products. Mostly I gave reasons why products should NOT be renamed, and why it was important to name the products correctly at the beginning.
IBM System Storage SAN Volume Controller hardware and software
Fellow IBM master inventory Barry Whyte has been covering the latest on the [SVC 2145-CF8 hardware]. IBM put out a press release last week on this, and today is the formal announcement with prices and details. Barry's latest post
[SVC CF8 hardware and SSD in depth] covers just part of the entire
The other part of the announcement was the [SVC 5.1 software] which can be loaded
on earlier SVC models 8F2, 8F4, and 8G4 to gain better performance and functionality.
To avoid confusion on what is hardware machine type/model (2145-CF8 or 2145-8A4) and what is software program (5639-VC5 or 5639-VW2), IBM has introduced two new [Solution Offering Identifiers]:
5465-028 Standard SAN Volume Controller
5465-029 Entry Edition SAN Volume Controller
The latter is designed for smaller deployments, supports only a single SVC node-pair managing up to
150 disk drives, available in Raven Black or Flamingo Pink.
EXN3000 and EXP5060 Expansion Drawers
IBM offers the [EXN3000 for the IBM N series]. These expansion drawers can pack 24 drives in a 4U enclosure. The drives can either be all-SAS, or all-SATA, supporting 300GB, 450GB, 500GB and 1TB size capacity drives.
The [EXP5060 for the IBM DS5000 series] is a high-density expansion drawer that can pack up to 60 drives into a 4U enclosure. A DS5100 or DS5300
can handle up to eight of these expansion drawers, for a total of 480 drives.
Pre-installed with Tivoli Storage Productivity Center Basic Edition. Basic Edition can be upgraded with license keys to support Data, Disk and Standard Edition to extend support and functionality to report and manage XIV, N series, and non-IBM disk systems.
Pre-installed with Tivoli Key Lifecycle Manager (TKLM). This can be used to manage the Full Disk Encryption (FDE) encryption-capable disk drives in the DS8000 and DS5000, as well as LTO and TS1100 series tape drives.
IBM Tivoli Storage FlashCopy Manager v2.1
The [IBM Tivoli Storage FlashCopy Manager V2.1] replaces two products in one. IBM used
to offer IBM Tivoli Storage Manager for Copy Services (TSM for CS) that protected Windows application data, and IBM Tivoli Storage Manager for Advanced Copy Services (TSM for ACS) that protected AIX application data.
The new product has some excellent advantages. FlashCopy Manager offers application-aware backup of LUNs containing SAP, Oracle, DB2, SQL server and Microsoft Exchange data. It can support IBM DS8000, SVC and XIV point-in-time copy functions, as well as the Volume Shadow Copy Services (VSS) interfaces of the IBM DS5000, DS4000 and DS3000 series disk systems. It is priced by the amount of TB you copy, not on the speed or number of CPU processors inside the server.
Don't let the name fool you. IBM FlashCopy Manager does not require that you use Tivoli Storage Manager (TSM) as your backup product. You can run IBM FlashCopy Manager on its own, and it will manage your FlashCopy target versions on disk, and these can be backed up to tape or another disk using any backup product. However, if you are lucky enough to also be using TSM, then there is optional integration that allows TSM to manage the target copies, move them to tape, inventory them in its DB2 database, and provide complete reporting.
Yup, that's a lot to announce in one day. And this was just the disk-related portion of the launch!
A lot was announced yesterday, so I decided to break it up into several separate posts. This is part 2 in my 3-part series, focusing on: Storwize V7000 Unified, LTO-6 tape, and the SmartCloud Virtual Storage Center.
The Storwize V7000 Unified is a product that consists of a 2U-high Storwize V7000 control enclosure that provides block-based access, combined with two 2U-high File Modules that provide file-based NAS protocols: CIFS, NFS, HTTPS, SCP and FTP. The problem was that when it was introduced, it was based on Storwize V7000 v6.3, so when the Storwize V7000 v6.4 features were announced last June, they did not apply to the Storwize V7000 Unified.
That is all fixed now, so the Storwize V7000 Unified now supports the full v6.4 features, including Real-time Compression for both file and block-based access to primary data, and Fibre Channel over Ethernet (FCoE) for block access.
The two File Modules are no longer limited to a single Storwize V7000 control enclosure, you can now connect to up to four control enclosures clustered together. Combined with up to nine expansion enclosures for additional disk raises the total maximum to 960 drives.
If you don't already have an Active Directory or LDAP server, the Storwize V7000 Unified now offers an embedded LDAP server, for smaller deployments that want to reduce the number of servers they need to purchase for a complete solution.
Like the [IBM XIV Gen3 storage system], both the Storwize V7000 and V7000 Unified now also support the OpenStack Nova-volume interface.
Lastly, if you have a Storwize V7000 v6.4, you can upgrade it to a Storwize V7000 Unified by simply adding the two File Modules. This can be done in the field.
IBM LTO-6 for tape libraries and drives
IBM introduces the sixth generation of Linear Tape Open (LTO-6) drives, which can be used as stand-alone IBM TS1060 drives, or in IBM tape libraries. As with previous models of LTO, the LTO-6 can read two older generations (LTO-4 and LTO-5) tape media, and can write to previous generation (LTO-5) tape media. You can buy the LTO-6 drives now, and use the older media until LTO-6 tape cartridges are available (hopefully later this year!)
My friend, Brad Johns, from Brad Johns Consulting, has a great post on this [LTO-6 Announcement]. While you expect the new drives to be faster with a denser tape media format, the key advantage to the LTO-6 is that it improves the compression algorithm, from the previous 2:1 to the new 2.5:1 compression ratio:
Thus, with the improved compression, the LTO-6 is 40 percent faster, with double the tape cartridge density. This can reduce backup times by 30 percent, increase the amount of data that sits in your automated tape libraries, and reduce the courier costs sending tapes off-site.
IBM SmartCloud Virtual Storage Center v5.1
Last year, IBM coined the phrase "Storage Hypervisor" to refer to the underlying technology in the IBM SAN Volume Controller (SVC) and Storwize V7000 disk systems.
At the IBM Edge conference last June, my colleague Mike Griese presented [SmartCloud Virtual Storage Center]. Back then, it was a pilot program (beta test), and this week, IBM announces that it will be formally available as a product.
The idea was simple: take the basic storage hypervisor, and add the necessary software to make it a complete solution.
If all of your disk is currently virtualized behind IBM SAN Volume Controller (SVC), or you want to put all of your data behind SVC, then SmartCloud Virtual Storage Center is for you. Basically, for one per-TB price, you get all of the following:
The software features of SAN Volume Controller v6.4, including FlashCopy, Metro Mirror and Global Mirror.
The full advanced features of IBM Tivoli Storage Productivity Center v5.1, including the Storage Analytics Engine that does "Right-Tiering", recommending which LUNs should be moved entirely from one disk system to another, based on policies and access patterns.
IBM Tivoli Storage FlashCopy Manager v3.2 which manages FlashCopy with full coordination with applications, including Microsoft Exchange, SQL Server, DB2, Oracle, SAP, and VMware. This ensures that the FlashCopy destination copies are clean, eliminating the need to run backout or redo logs to correct any incomplete units of work.
If this combination sounds familiar, it was based on IBM's previous attempt called [Rapid Application Storage] which combined the Storwize V7000 with Tivoli Storage Productivity Center Midrange Edition and FlashCopy Manager.
The key difference is that SmartCloud VSC does not include the SVC hardware itself, you buy this separately. If you want Real-time Compression, that is charged separately for the subset of TB of the volumes that you select for compression.
Earlier this week, Jon Erickson from Forrester Reserch, and Chris Saul from IBM, co-presented a webcast on the economic impact of using SAN Volume Controller for storage virtualization. The event was co-sponsored by IBM, InformationWeek, and UBM TechWeb, The Global Leader in Business Technology Media, a Division of UBM LLC. Jon spoke first, covering the cost savings and financial benefits of using SAN Volume Controller in your environment. His analysis shows a payback period of only 18 months!
Chris Saul (IBM) then covered the latest features introduced last June for SAN Volume Controller v6.4 release. Many of these features are available on older hardware models of SAN Volume Controller. One of the most exciting features is Real-time Compression.
If you missed the webcast, you can listen to the [Replay]. There is also a [whitepaper] if you prefer that format.
The Real-time Compression benefits can vary by the type of data compressed. Some data compresses only 20% savings. Other data compresses 80% or more. The best way to find out how much Compression would benefit your environment is to run the [IBM Comprestimator Tool] that runs against your own data!
If you are constantly battling out-of-space conditions, and would like to make extra room on your existing storage devices, your dreams have come true!
This week, I am in Taipei, teaching Top Gun class. There was concern that another typhoon would hit the island of Taiwan later this week, but it looks like it is now headed for Hong Kong instead.
Elsewhere in the world, there are several events going on next week, so I thought I would bring them to your attention.
ECTY - South Africa
Next week, Jerry Kluck, IBM Global Sales Executive for Storage Optimization and Integration Services, will be the keynote speaker at "Edge Comes to You" (ECTY) conference in South Africa. This is a one-day event, similar to the [ECTY event in Moscow, Russia] that I spoke at last June.
Here is the schedule for South Africa next week:
Monday, August 20, 2012 - Johannesburg
Wednesday, August 22, 2012 - Cape Town
(I have been to both Jo'burg and Cape Town back in 1994. A month after Apartheid had just ended, I was part of a small group of IBMers sent to re-establish IBM's business operations there. I would have liked to have attended the events next week, not just to hear Jerry speak, but also to see how much the country has changed over the past 18 years, but I could not get a work permit in time.)
If you are interested in attending either of these next week, contact your local IBM Business Partner or sales rep to attend.
Forrester's Total Economic Impact Study of Virtualized Storage
Virtualized storage can help organizations stretch their storage investment dollar and storage administration and management resources. Jon Erickson from Forrester Research will review the latest findings from IBM SAN Volume Control (SVC) users studied as part of the recently completed Forrester Total Economic Impact Study of IBM System Storage SAN Volume Controller.
Date: Tuesday, August 21, 2012
Time: 10:00 AM PDT / 1:00 PM EDT
Duration: 60 minutes
Among the findings, users were able to:
Avoid the capital cost of additional storage
Increase IT productivity
Provide greater end user data availability
The second presenter is Chris Saul, IBM Storage Virtualization Manager, who will explain how SVC can manage heterogeneous disk from a single point of control, autonomously manage tiered disk storage and can store up to five times as much data on your existing disk using IBM Real-time Compression.
Not all virtualization solutions are created equal! That's true for storage virtualization, like the SAN Volume Controller mentioned above, and it's true for server virtualization as well.
This webcast discusses the real-world impact on businesses that deploy IBM's PowerVM®
virtualization technology as compared to those using Oracle® VM for SPARC (OVM SPARC), Microsoft® Hyper-V, VMware® vSphere or other competing products.
Date: Wednesday, August 22, 2012
Time: 10:00 AM PDT / 1:00 PM EDT
Duration: 60 minutes
This webcast will include findings from a [Solitaire Interglobal] study of over 61,000 customer sites on the value of virtualization from a business perspective and how IBM's PowerVM provides real business value.
Other key discussion points that will be covered during this webcast include:
Behavioral characteristics of server virtualization technologies that were examined and analyzed from survey participant's environments
How IT colleagues were able to obtain a faster time-to-market for business initiatives when using IBM PowerVM
Why the learning curve time for PowerVM is as much as 2.58 times faster than for other offerings
Why VM reboot comparisons for PowerVM vs competitive platforms resulted in downtime of 5.5 times less than with other options
A TCO reduction of up to 71.4% for PowerVM compared to alternative options
This webcast will also feature an in-depth discussion on the IBM PowerVM solution from an IBM product expert who will share the unique virtualization features available when PowerVM is utilized within the IBM Power Systems™ environment.
Every year, I teach hundreds of sellers how to sell IBM storage products. I have been doing this since the late 1990s, and it is one task that has carried forward from one job to another as I transitioned through various roles from development, to marketing, to consulting.
This week, I am in the city of Taipei [Taipei] to teach Top Gun sales class, part of IBM's [Sales Training] curriculum. This is only my second time here on the island of Taiwan.
As you can see from this photo, Taipei is a large city with just row after row of buildings. The metropolitan area has about seven million people, and I saw lots of construction for more on my ride in from the airport.
The student body consists of IBM Business Partners and field sales reps eager to learn how to become better sellers. Typically, some of the students might have just been hired on, just finished IBM Sales School, a few might have transferred from selling other product lines, while others are established storage sellers looking for a refresher on the latest solutions and technologies.
I am part of the teach team comprised of seven instructors from different countries. Here is what the week entails for me:
Monday - I will present "Selling Scale-Out NAS Solutions" that covers the IBM SONAS appliance and gateway configurations, and be part of a panel discussion on Disk with several other experts.
Tuesday - I have two topics, "Selling Disk Virtualization Solutions" and "Selling Unified Storage Solutions", which cover the IBM SAN Volume Controller (SVC), Storwize V7000 and Storwize V7000 Unified products.
Wednesday - I will explain how to position and sell IBM products against the competition.
Thursday - I will present "Selling Infrastructure Management Solutions" and "Selling Unified Recovery Management Solutions", which focus on the IBM Tivoli Storage portfolio, including Tivoli Storage Productivity Center, Tivoli Storage Manager (TSM), and Tivoli Storage FlashCopy Manager (FCM). The day ends with the dreaded "Final Exam".
Friday - The students will present their "Team Value Workshop" presentations, and the class concludes with a formal graduation ceremony for the subset of students who pass. A few outstanding students will be honored with "Top Gun" status.
These are the solution areas I present most often as a consultant at the IBM Executive Briefing Center in Tucson, so I can provide real-life stories of different client situations to help illustrate my examples.
The weather here in Taipei calls for rain every day! I was able to take this photo on Sunday morning while it was still nice and clear, but later in the afternoon, we had quite the downpour. I am glad I brought my raincoat!
This week I am in Orlando, Florida for the IBM Edge conference. This is the last day, so it ends early for people who want to get home to their datacenters (er.. families) for the weekend.
How Real-Time Compression Can Maximize Storage Efficiency for Production Applications
This was a split session with two speakers. First, Ian Rimmer, Senior IT Engineer and Architect at iBurst, presented their experience with the IBM Real-Time Compression Appliance in front of NetApp NAS storage arrays. Second, Jerry Haigh, IBM offering manager for IBM System Storage, presented the new Real-Time compression feature announced this week on IBM SAN Volume Controller (SVC) and Storwize V7000.
iBurst is the #1 Wireless Telecom for South Africa. The also offer cable broadband and VOIP. They have 200 employees servicing 120,000 subscriber/households. They need to keep five years' worth of text files, and have chosen real-time compression of their NAS storage. This was before IBM acquired the Storwize company, as they have been using it for the past six years.
The monetary savings from compression was used to purchase Performance Accelerator Modules (PAM) cards for their NetApp NAS gear, which benefit from the compression (more data stored in SSD to improve performance).
For backup, they use NDMP with Symantec NetBackup that keeps data in its compressed form as it is written to tape. They have an IBM TS3100 library with LTO tape as the backup repository.
Jerry Haigh presented Real-Time compression for primary disk data. Unlike the competition, this is designed to be used with primary data, including databases, and does this real-time, not post-process. In some performance tests, DB2 compressed on 48 drives out-performed the same data uncompressed on 96 drives. In another test focused on VMware Vmark benchmark, the compressed data was able to be same or better performance as uncompressed. In a third test with SVC virtualizing XIV running Oracle ORION test, the Oracle databases compressed 50 to 64 percent, and had better performance.
For those who already have SVC or Storwize V7000, consider a 45-day trial to check out compression for yourself.
NAS File Systems: Access and Authentication
Mark Taylor, IBM Technical Specialist for SONAS, N series and Storwize V7000 Unified, presented the nuances of authentication and authorization for NAS file systems. The differences between these two are:
Authentication - Yes, you are who you are.
Authorization - Yes, you are permitted to do what you are trying to do
(Prior to working with SONAS, my only experience with access and authentication in NAS was setting up my LAN at home, which I have connecting my Mac, Linux and Windows machines. I have both N series and SONAS at the IBM Executive Briefing Center in Tucson, Arizona, so I know first-hand how complicated NAS access and authentication systems can be.
A few months ago, I taught "Intro to NAS" as one of my topics at the Top Gun class in Argentina and Brazil. Several of the students had mentioned they thought they knew NAS solutions but had not realized all the technical issues with access and authentication that I discussed in my presentation.)
Mark explained the differences between Windows NTFS-style System identifiers (SID), versus UNIX-style user and group identifiers (UID, GID). For NAS solutions that support both CIFS and NFS, there are four options:
Microsoft Active Director (AD) extended with Identity Management for UNIX, formerly known as Services for UNIX (SFU). AD servers normally store SID information, but the extensions add extra columns to hold UID/GID mappings.
AD with Network Information Service (NIS) server. The problem with this approach is that AD and NIS are separate databases, and you need to coordinate updates to them, and their backups.
Lightweight Directory Access Protocol (LDAP) with SAMBA extensions. LDAP holds UID/GID information, and the SAMBA extensions adds extra columns to hold SID mapping.
Local mapping. The dangerous part of local mapping is that the storage admin is also the security admin, and you may want different people doing these roles.
Of these four methods, Mark recommends the first and third as best practices for multi-protocol authentication.
SID-to-UID mapping, UID-to-SID mapping
SONAS and Storwize V7000
SID-to-UID/GID mapping, NFS v4 ACLs
NFS v4 ACLs
Mark then explained how NFS v4 ACLs work, basically an ordered collection of "Access Control Elements" or ACEs. Each ACE on the ACL may "allow" or "deny" the request. You want to avoid "Inheritance" as that can cause problems and unxpected results.
That's it folks. Next week, I am spending time with my research buddies at the Almaden Research Center near San Jose, California, and then it is off to Moscow, Russia to kick off a series of IBM events called "Edge Comes to You" (ECTY).
The ECTY conferences will be a smaller subset of the Edge conference here in Orlando, but offered in other countries for those who were unable to travel to the United States.
This week I am in Orlando, Florida for the IBM Edge conference. Thursday evening after all the other sessions, we had a Free-for-All, a Q&A panel across all storage topics, moderated by Scott Drummond. The conference officially ends at noon tomorrow, but for many, this is the last session, as people fly out Friday morning. Here are the questions and the panel responses during the session.
When will IBM unify their storage management between Mainframe z/OS and the distributed systems platforms?
IBM offers a Change and Configuration Management Data Base (CCMDB) for this purpose with appropriate collectors from z/OS and distributed systems, but hasn't sold well.
When will IBM devices have RESTful interfaces?
Both IBM Systems Director and IBM Tivoli Storage Productivity Center (TPC) offer RESTful APIs. IBM Systems Director can manage z/VM and Linux on System z, as well as Power Systems and x86 based distributed systems. Since October 2008, IBM's Project Zero introduced RESTful interfaces to PHP and Groovy software running on WebSphere sMash environments. We have not heard much about this since 2008.
Will IBM TPC support NPIV on Power Systems?
TPC 5.1 has toleration support for this, showing the first port connection discovered, but not all connections, and we expect to retrofit this toleration to TPC 4.2.2 Fixpack 2. Hopefully, we will have full support in a future release.
We would like TPC for Replication to run on Linux for System z. We do not run z/OS at the disaster recovery site location.
Submit an IBM Request for Enhancement [RFE] for this. We have TPC for Replication on z/OS, as well as the distributed systems version that runs on Windows, Linux and AIX.
We have enhancements we would like to see for XIV and SONAS also, can we use the RFE process for this also?
Yes, submit the requirements for our review.
We heard the Statement of Direction that there would be storage integrated into the PureSystems. What exactly does that mean?
The PureSystems family of expert-integrated systems is based on a new chassis that has a front part, a midplane, and a back-part. All IBM System Storage products that support x86 and Power Systems can work with PureSystems. However, IBM does not yet offer storage that fits in the front part of the PureFlex chassis, but the Statement of Direction indicates that we intend to offer that option. Until then, the IBM Storwize V7000 is the storage of choice that can be put into the PureSystems rack, but outside the individual chasses.
We see some features like Real-Time Compression being put into the SAN Volume Controller (SVC), and other features put into the back-end devices. How are we supposed to make sense of this?
IBM's new pilot program, the SmartCloud Virtual Storage Center, to bring these all together. In general, we have design teams of system architects that determine which features go in which products, and prioritize accordingly.
We heard the IBM Executives during the opening session indicate that IBM's strategy involves supporting Big Data, but I haven't seen any storage that supports native Hadoop interfaces. Did I miss something?
First, I want to emphasize that Big Data is more than just MapReduce workloads. IBM offers Streams and BigInsights software to handle text, as well as Business Intelligence and Data Warehouse solutions for structured data. IBM's General Parallel File System (GPFS) has a Shared-Nothing-Cluster (SNC) mode with Hadoop interfaces that runs twice as fast as Hadoop's native HDFS file system. The storage products we recommend for Big Data are the SONAS and the DCS3700 disk systems, as both are optimized for the sequential workloads Big Data represents.
Everytime we upgrade our SVC, we review the list for SDDPCM multi-pathing and see that we need to upgrade our back-end DS8000 microcode up to recommended levels. Can we get a list of combinations that work from other customers?
The advantage of storage hypervisors like SVC is that we can separate the multi-pathing driver from the back-end managed disk systems. You only need the SDDPCM to support the SVC, not the back-end devices. For the most part, SVC has not dropped support for any level of previously supported OS or multi-pathing software.
On SVC, when we migrate volumes (vDisks) from one storage pool to another, we would like to throttle this process during FlashCopy.
Yes, we had several requests like this, which is why we now recommend using Volume Mirorring to perform migrations. In fact the GUI wizard uses Volume Mirroring by default when migrations are performed. As for throttling, IBM has implemented "I/O Priority Manager" that offers Quality of Service classes for DS8000 and XIV Gen3, and might consider porting this to other products in our portfolio.
Sizing systems is an art. I just need to know if the DS8000 is running hot. Can we have the equivalent of "red lines" for our disk systems similar to automobile engines?
Storage Optimizer was added to TPC 4.2 to help in this area, identifying heat-maps for IBM DS8000, DS6000, DS5000, DS4000, SVC and Storwize V7000. We recommend you look at the performance violation reports.
How can we evaluate the characteristics of our workloads?
Yes, TPC can do this.
When we are replacing non-IBM storage with IBM, we don't have good tools to evaluate the non-IBM equipment. What is IBM doing for this?
IBM's Disk Magic modeling tool can take inputs from a variety of sources, including iostat from the servers themselves. You can also install a 90-day trial of TPC to help with this.
We really like EMC's "Grab" program, does IBM have one also?
Updating the Host Attachment Kit (HAK) for AIX is quite painful for the SVC. We prefer the method employed for the XIV.
Thanks for the feedback.
For SVC, we need to correlate disk with VMware and VIOS. Can we get vSCSI information on VIOS?
TPC 5.1 has this support, and we believe it has been retrofitted to TPC 4.2.2 Fixpack 2, coming out this month.
Currently, with SVC, when volumes are part of a Global Mirror (GM) session, we need to cancel GM, expand the source volume, expand the target volume, then restart GM. We would like this to be fully automated and non-disruptive.
Sounds like a great requirement to submit for the RFE process.
Can we get an RSS Feed for the RFE community.
Yes, you can subscribe to it. You can also set up "Watch Lists".
Thanks to all of the IBM experts on the panel for their participation at this event!
Earlier this year, I wrote a Web article titled [Data Footprint Reduction] which covered data deduplication and compression, and was asked to present this at IBM Edge. I have expanded it to include:
Space-Efficient Point-in-Time copies
After I presented the basic concepts, Sanjay Bhikot, a Unix and Storage admin at RICOH, presented his real-world experiences with data deduplication using the IBM ProtecTIER and real-time compression Beta experience using the SAN Volume Controller (SVC).
IBM Active Cloud Engine Implementation on IBM SONAS 1.3 and IBM Storwize V7000 Unified
John Sing (IBM) presented the latest enhancements in the v1.3.2 release of SONAS and Storwize V7000 Unified.
Introducing VMware vSphere Storage Features
Fellow blogger Stephen Foskett presented this session on VMware's storage features. This included VMware APIs for Array Integration (VAAI), VMware Array Storage Awareness (VASA), vCenter plug-ins, and a new concept he called "vVol" which de-multiplexes the "I/O Blender" that server hypervisors do by tagging individual requests to individual OS guests to provide added benefit. IBM is a leading reseller of VMware, so it makes sense that most of our storage meets all of Steve's requirements for recommendation.
IBM's Storage Strategy in the Smarter Computing Era
Last year, I presented this on the fourth day of the conference, and feedback we received from attendees was that this should have been presented sooner in the week, as it provides great context for the more detailed product presentations.
To address this concern, the IBM executives presented IBM strategy on Monday's keynote session, but allowed me to present this on Wednesday for several reasons:
You may have missed the keynote session. For example, you may not have arrived in time to hear the executives speak due to weather or mechanical problems causing travel delays.
You may have attended the keynote session, but want to hear it again. Maybe you were a bit hung-over, or just may have been overwhelmed with the size and scope of this event. I have read for strategic topics, audiences may have to hear the message five to seven times before they truly appreciate and understand it.
You may want to ask questions, and explore the implications in more detail. While keynote sessions can reach a broader audience, the communication is very much uni-directional. With break-out sessions with a few hundred people, the venue is more intimate and can afford opportunties for information exchange.
The title of this session rolls off the tongue nicely, much like "James and the Giant Peach", "Harold and the Purple Crayon", or "Charlie and the Chocolate Factory".
When people say they are interested in "Cloud Storage", what exactly do they mean. After discussions with hundreds of clients, IBM has worked out a "taxonomy" that identifies four distinct types of storage:
In this session, I presented how IBM SONAS addresses all four of these categories, as well as other IBM storage products that can address specific categories in the taxonomy.
In the evening, the attendees at IBM Edge joined the attendees from Innovate2012 (focused on IBM Rational products) at SeaWorld, with BBQ dinner, rides, Shamu the whale show, and a concert featuring Foreigner!
Well it's Tuesday again, and you know what that means... IBM announcements! Yesterday, at the IBM Edge conference here in Orlando, Florida, IBM announced its new apporach to storage, and a whole bunch of storage products, enhancements, and services. I will focus on some key ones here, and save the rest for next week.
IBM SAN Volume Controller (SVC) v6.4
The SVC is IBM's enterprise-class storage hypervisor. The latest software release, v6.4, can be installed on any SVC hardware, from the 2145-8F2 introduced back in 2005, to newer models like the 2145-CG8. Here are the key features:
Fibre Channel over Ethernet (FCoE) -- This is complete end-to-end support. For SVC units with 10GbE ports, these ports can be now be used for FCoE. This allows hosts to attach to SVC via FCoE, allows SVC node-to-node communication for clustering, and allows SVC to communicate to back-end devices via FCoE.
Real-Time Compression -- IBM ported over the patent Random Access Compression Engine (RACE) from the Real-Time Compression Appliances to SVC v6.4. This allows primary data, accessed via block-based protocols, to be compressed up to 80 percent. This feature is an extra priced feature by TB.
Non-Disruptive Volume move between I/O Groups -- If you don't already have SVC, you don't need to worry about this. For existing SVC customers, this allows volumes to be associated with two or more I/O groups, and that you can add or remove I/O groups non-disruptively. For example, if you want to move a volume from IOG1 to IOG2, then you add IOG2 to the list of I/O groups for the volume, let the multi-pathing software discover the additional paths, the remove IOG1, which then marks the previous IOG1 paths inactive. All this can be done while applications read and write data.
Dedicate FCP ports for Replication -- If you activate the two 10GbE Ethernet ports for FCoE, you can free up two FCP ports that you can dedicate for long-distance Metro Mirror or Global Mirror.
If you have SVC today, but are running an old release like v4.3 or v5.1, I recommennd you upgrade up to at least v6.2.05 release now. This release has been out for a year and is very stable, and serves as a great platform for a later upgrade to SVC v6.4.
IBM Storwize V7000 v6.4
The Storwize V7000 is IBM's midrange storage hypervisor. The latest software release, v6.4, can be installed on existing block-only Storwize V7000 units in the field. The Storwize V7000 v6.4 gets all the features listed above, as well as the following:
Four-way clustering -- Previously, you could cluster two Storwize V7000 controller enclosures together (4 canisters total). To cluster three or four controllers required an RPQ. Now, IBM supports up to four Storwize V7000 controller enclosures (8 canisters) without an RPQ.
Direct Fibre Channel attach -- A lot of people are using Storwize V7000 inside single-rack configurations, so it makes sense not to require a SAN switch for just a few Windows, Linux or VMware servers. An RPQ is now available to allow this to happen.
IBM Tivoli Storage Productivity Center (TPC) v5.1
TPC is already ranked one of the best Storage Infrastructure Management software in the market, and this release will just solidify its lead. Key features include:
Upward integration to higher level management systems
A new, intuitive, easy-to-use web-based GUI inspired by the XIV GUI
Integration of COGNOS to be able to generate and customize reports
Support for SONAS systems
There are several presentations on TPC this week that will go into more detail. Check out the [TPC Facebook page].
My latest book Inside System Storage: Volume IV is now available!
Yes, can you believe it? I have published my fourth volume in my "Inside System Storage" series! It is available in three formats:
Hardcover with dust jacket
eBook (Adobe Acrobat PDF)
You can order this, and all my other books, in all formats, directly from my [Author Spotlight] page. The paperback will also be available soon from other online booksellers, search for ISBN 978-1-105-72213-4.
IBM DS3500 Express
The DS3500 is our entry-level block-based device, designed specifically for random I/O workloads. This includes databases, email repositories, traditional business applications, and on-line transactional workloads. Here are the new features:
Dynamic Disk Pooling, similar to what XIV does to reduce disk rebuild times, but using a RAID-6 like approach per chunk of data.
Thin Provisioning using Dynamic Disk Pooling
Asynchronous Logical Unit Access (ALUA) failover
Enhanced FlashCopy, improved scalability, consistency groups and rollback support
VMware API for Array Integration (VAAI) support. This includes Write Same, Extended Copy, and Atomic Test & Set.
The DS3500 replaces the previous models of DS3200, DS3300 and DS3400 models.
The DCS3700 is our entry-level/midrange block-based device, replacing the DCS9900 model, designed specifically for sequential I/O workloads. This includes Big Data analytics, Hadoop, High Performance Computing (HPC), video surveillance, and television broadcasting. It holds 60 drives in a 4U controller enclosure.
Well, it's Wednesday, and you know what that means... IBM Announcements!
(Actually most IBM announcements are on Tuesdays, but IBM gave me extra time to recover from my trip to Europe!)
Today, IBM announced [IBM PureSystems], a new family of expert-integrated systems that combine storage, servers, networking, and software, based on IBM's decades of experience in the IT industry. You can register for the [Launch Event] today (April 11) at 2pm EDT, and download the companion "Integrated Expertise" event app for Apple, Android or Blackberry smartphones.
(If you are thinking, "Hey, wait a minute, hasn't this been done before?" you are not alone. Yes, IBM introduced the System/360 back in 1964, and the AS/400 back in 1988, so today's announcement is on scheduled for this 24-year cycle. Based on IBM's past success in this area, others have followed, most recently, Oracle, HP and Cisco.)
Initially, there are two offerings:
IBM PureFlex™ System
IBM PureFlex is like IaaS-in-a-box, allowing you to manage the system as a pool of virtual resources. It can be used for private cloud deployments, hybrid cloud deployments, or by service providers to offer public cloud solutions. IBM drinks its own champagne, and will have no problem integrating these into its [IBM SmartCloud] offerings.
To simplify ordering, the IBM PureFlex comes in three tee-shirt sizes: Express, Standard and Enterprise.
IBM PureFlex is based on a 10U-high, 19-inch wide, standard rack-mountable chassis that holds 14 bays, organized in a 7 by 2 matrix. Unlike BladeCenter where blades are inserted vertically, the IBM PureFlex nodes are horizontal. Some of the nodes take up a single bay (half-wide), but a few are full-wide, take up two bays, the full 19-inch width of the chassis. Compute and storage snap in the front, while power supplies, fans, and networking snap in the back. You can fit up to four chassis in a standard 42U rack.
Unlike competitive offerings, IBM does not limit you to x86 architectures. Both x86 and POWER-based compute nodes can be mixed into a single chassis. Out of the box, the IBM PureFlex supports four operating systems (AIX, IBM i, Linux and Windows), four server hypervisors (Hyper-V, Linux KVM, PowerVM, and VMware), and two storage hypervisors (SAN Volume Controller and Storwize V7000).
There are a variety of storage options for this. IBM will offer SSD and HDD inside the compute nodes themselves, direct-attached storage nodes, and an integrated version of the Storwize V7000 disk system. Of course, every IBM System Storage product is supported as external storage. Since Storwize V7000 and SAN Volume Controller support external virtualization, many non-IBM devices will be supported automatically as well.
Networking is also optimized, with options for 10Gb and 40Gb Ethernet/FCoE, 40Gb and 56Gb Infiniband, 8Gbps and 16Gbps Fibre Channel. Much of the networking traffic can be handled within the chassis, to minimize traffic on external switches and directors.
For management, IBM offers the Flex System Manager, that allows you to manage all the resources from a single pane of glass. The goal is to greatly simplify the IT lifecycle experience of procurement, installation, deployment and maintenance.
IBM PureApplication™ System
IBM PureApplication is like PaaS-in-a-box. Based on the IBM PureFlex infrastructure, the IBM PureApplication adds additional software layers focused on transactional web, business logic, and database workloads. Initially, it will offer two platforms: Linux platform based on x86 processors, Linux KVM and Red Hat Enterprise Linux (RHEL); and a UNIX platform based on POWER7 processors, PowerVM and AIX operating system. It will be offered in four tee-shirt sizes (small, medium, large and extra large).
In addition to having IBM's middleware like DB2 and WebSphere optimized for this platform, over 600 companies will announce this week that they will support and participate in the IBM PureSystems ecosystem as well. Already, there are 150 "Patterns of Expertise" ready to deploy from IBM PureSystem Centre, a kind of a "data center app store", borrowing an idea used today with smartphones.
By packaging applications in this manner, workloads can easily shift between private, hybrid and public clouds.
If you are unhappy with the inflexibility of your VCE Vblock, HP Integrity, or Oracle ExaLogic, talk to your local IBM Business Partner or Sales Representative. We might be able to buy your boat anchor off your hands, as part of an IBM PureSystems sale, with an attractive IBM Global Financing plan.
Have you ever noticed that sometimes two movies come out that seem eerily similar to each other, released by different studios within months or weeks of each other? My sister used to review film scripts for a living, she would read ten of them and have to pick her top three favorites, and tells me that scripts for nearly identical concepts came all the time. Here are a few of my favorite examples:
1994: [Wyatt Earp] and [Tombstone] were Westerns recounting the famed gunfight at the O.K. Corral. Tombstone, Arizona is near Tucson, and the gunfight is recreated fairly often for tourists.
1998: [Armageddon] and [Deep Impact] were a pair of disaster movies dealing with a large rock heading to destroy all life on earth. I was in Mazatlan, Mexico to see the latter, dubbed in Spanish as "Impacto Profundo".
1998: [A Bug's Life] and [Antz] were computer-animated tales of the struggle of one individual ant in an ant colony.
2000: [Mission to Mars] and [Red Planet] were sci-fi pics exploring what a manned mission to our neighboring planet might entail.
This is different than copy-cat movies that are re-made or re-imagined many years later based on the previous successes of an original. Ever since my blog post [VPLEX: EMC's Latest Wheel is Round] in 2010 comparing EMC's copy-cat product that came our seven years after IBM's SAN Volume Controller (SVC), I've noticed EMC doesn't talk about VPLEX that much anymore.
This week, IBM announced [XIV Gen3 Solid-State Drive support] and our friends over at EMC announced [VFCache SSD-based PCIe cards]. Neither of these should be a surprise to anyone who follows the IT industry, as IBM had announced its XIV Gen3 as "SSD-Ready" last year specifically for this purpose, and EMC has been touting its "Project Lightning" since last May.
Fellow blogger Chuck Hollis from EMC has a blog post [VFCache means Very Fast Cache indeed] that provides additional detail. Chuck claims the VFCache is faster than popular [Fusion-IO PCIe cards] available for IBM servers. I haven't seen the performance spec sheets, but typically SSD is four to five times slower than the DRAM cache used in the XIV Gen3. The VFCache's SSD is probably similar in performance to the SSD supported in the IBM XIV Gen3, DS8000, DS5000, SVC, N series, and Storwize V7000 disk systems.
Nonetheless, I've been asked my opinions on the comparison between these two announcements, as they both deal with improving application performance through the use of Solid-State Drives as an added layer of read cache.
(FTC Disclosure: I am both a full-time employee and stockholder of the IBM Corporation. The U.S. Federal Trade Commission may consider this blog post as a paid celebrity endorsement of IBM servers and storage systems. This blog post is based on my interpretation and opinions of publicly-available information, as I have no hands-on access to any of these third-party PCIe cards. I have no financial interest in EMC, Fusion-IO, Texas Memory Systems, or any other third party vendor of PCIe cards designed to fit inside IBM servers, and I have not been paid by anyone to mention their name, brands or products on this blog post.)
The solutions are different in that IBM XIV Gen3 the SSD is "storage-side" in the external storage device, and EMC VFCache is "server-side" as a PCI Express [PCIe] card. Aside from that, both implement SSD as an additional read cache layer in front of spinning disk to boost performance. Neither is an industry first, as IBM has offered server-side SSD since 2007, and IBM and EMC have offered storage-side SSD in many of their other external storage devices. The use of SSD as read cache has already been available in IBM N series using [Performance Accelerator Module (PAM)] cards.
IBM has offered cooperative caching synergy between its servers and its storage arrays for some time now. The predecessor to today's POWER7-based were the iSeries i5 servers that used PCI-X IOP cards with cache to connect i5/OS applications to IBM's external disk and tape systems. To compete in this space, EMC created their own PCI-X cards to attach their own disk systems. In 2006, IBM did the right thing for our clients and fostered competition by entering in a [Landmark agreement] with EMC to [license the i5 interfaces]. Today, VIOS on IBM POWER systems allows a much broader choice of disk options for IBM i clients, including the IBM SVC, Storwize V7000 and XIV storage systems.
Can a little SSD really help performance? Yes! An IBM client running a [DB2 Universal Database] cluster across eight System x servers was able to replace an 800-drive EMC Symmetrix by putting eight SSD Fusion-IO cards in each server, for a total of 64 Solid-State drives, saving money and improving performance. DB2 has the Data Partitioning Feature that has multi-system DB2 configurations using a Grid-like architecture similar to how XIV is designed. Most IBM System x and BladeCenter servers support internal SSD storage options, and many offer PCIe slots for third-party SSD cards. Sadly, you can't do this with a VFCache card, since you can have only one VFCache card in each server, the data is unprotected, and only for ephemeral data like transaction logs or other temporary data. With multiple Fusion-IO cards in an IBM server, you can configure a RAID rank across the SSD, and use it for persistent storage like DB2 databases.
Here then is my side-by-side comparison:
IBM XIV Gen3 SSD Caching
Selected x86-based models of Cisco UCS, Dell PowerEdge, HP ProLiant DL, and IBM xSeries and System x servers
All of these, plus any other blade or rack-optimized server currently supported by XIV Gen3, including Oracle SPARC, HP Titanium, IBM POWER systems, and even IBM System z mainframes running Linux
Operating System support
Linux RHEL 5.6 and 5.7, VMware vSphere 4.1 and 5.0, and Windows 2008 x64 and R2.
All of these, plus all the other operating systems supported by XIV Gen3, including AIX, IBM i, Solaris, HP-UX, and Mac OS X
FCP and iSCSI
Vendor-supplied driver required on the server
Yes, the VFCache driver must be installed to use this feature.
No, IBM XIV Gen3 uses native OS-based multi-pathing drivers.
External disk storage systems required
None, it appears the VFCache has no direct interaction with the back-end disk array, so in theory the benefits are the same whether you use this VFCache card in front of EMC storage or IBM storage
XIV Gen3 is required, as the SSD slots are not available on older models of IBM XIV.
Shared disk support
No, VFCache has to be disabled and removed for vMotion to take place.
Yes! XIV Gen3 SSD caching shared disk supports VMware vMotion and Live Partition Mobility.
Support for multiple servers
An advantage of the XIV Gen3 SSD caching approach is that the cache can be dynamically allocated to the busiest data from any server or servers.
Support for active/active server clusters
Aware of changes made to back-end disk
No, it appears the VFCache has no direct interaction with the back-end disk array, so any changes to the data on the box itself are not communicated back to the VFCache card itself to invalidate the cache contents.
None identified. However, VFCache only caches blocks 64KB or smaller, so any sequential processing with larger blocks will bypass the VFCache.
Yes! XIV algorithms detect sequential access and avoid polluting the SSD with these blocks of data.
Number of SSD supported
One, which seems odd as IBM supports multiple Fusion-IO cards for its servers. However, this is not really a single point of failure (SPOF) as an application experiencing a VFCache failure merely drops down to external disk array speed, no data is lost since it is only read cache.
6 to 15 (one per XIV module) for high availability.
Pin data in SSD cache
Yes, using split-card mode, you can designate a portion of the 300GB to serve as Direct-attached storage (DAS). All data written to the DAS portion will be kept in SSD. However, since only one card is supported per server and the data is unprotected, this should only be used for ephemeral data like logs and temp files.
No, there is no option to designate an XIV Gen3 volume to be SSD-only. Consider using Fusion-IO PCIe card as a DAS alternative, or another IBM storage system for that requirement.
Pre-sales Estimating tools
Yes! CDF and Disk Magic tools are available to help cost-justify the purchase of SSD based on workload performance analysis.
IBM has the advantage that it designs and manufactures both servers and storage, and can design optimal solutions for our clients in that regard.
IBM Tivoli Storage Productivity Center v4.2.2 Overview and Update
This was an updated version of the presentation I gave last July in Orlando, Florida (see my post [IBM Storage University - Day 1]). Since it might have been awhile since the Australian audience had heard about the latest and greatest for Tivoli Storage Productivity Center, I decided to cover the enhancements of 4.2.0, 4.2.1 and 4.2.1 combined.
IBM Tivoli Storage Productivity Center is an important part of IBM's "Storage Hypervisor" solution, combining a single pane of glass for management with non-disruptive storage virtualization with SVC and Storwize V7000.
IBM Storwize V7000 and SVC integration with VMware
Alexi Giral from IBM Sydney presented this session on how Storwize V7000 and SVC serve as the "Storage Hypervisor" for VMware server virtualization environments. The focus was on the FCP and iSCSI block-only access modes of these devices, although one could use IBM Storwize V7000 Unified to provide NFS file-level access to VMware. Alexi covered both VMware Vsphere v4 and v5, as there are a few differences.
IBM Storwize V7000 and SVC supports thin provisioning, VMware's VAAI interface, VMware's Site Recovery Manager, and provides a storage management plug-in to Vmware's vCenter. The SVC has extended the distance for split-cluster configurations that support VMware's vMotion live partition mobility and High Availiability (HA) up to 300km using active DWDM.
Tape Storage Reinvented: What's New and Exciting in the Tape World?
Special thanks to Jim Fisher and Jim Karp for providing me this presentation, videos and supporting materials for me to present this session. I gave this as the first break-out session on Tuesday, and then repeated as the last break-out session on Thursday. Several of the attendees in the audience mocked my title, with taunts like "What could be NEW or EXCITING about tape?" I covered four key areas:
The new TS1140 tape drive, including the corresponding model-JC tape that holds 4TB native (12 TB compressed!).
The enhanced TS3500 with the Tape Library Connector Shuttle. I had a video that shows how tapes can be sent from one TS3500 tape library string to another.
The new Linear Tape File System (LTFS), both the single drive edition and the library edition
The new 3592-C07 FICON controller for our mainframe clients
By the end of the session, the folks that taunted me were honestly impressed that they learned a few things, and had not realized so much has been developed recently in the world of tape.
Continuing my coverage of the [IBM System x and System Storage Technical Symposium], I thought I would start with some photos. I took these with cell phone, and without realizing how much it would cost, uploaded them to Flickr at international data roaming rates. Oops!
Here are some of the banners used at the conference. Each break-out session room was outfitted with a "Presentation Briefcase" that had everything a speaker might need, including power plug adapters and dry-erase markers for the whiteboard. What a clever idea!
Here is a recap of the last and final day 3:
Understanding IBM's Storage Encryption Options
Special thanks to Jack Arnold for providing me his deck for this presentation. I presented IBM's leadership in encryption standards, including the [OASIS Key Management Interoperability Protocol] that allows many software and hardware vendors to interoperate. IBM offers the IBM Tivoli Key Lifecycle Manager (TKLM v2) for Windows, Linux, AIX and Solaris operating systems, and the IBM Security Key Lifecycle Manager (v1.1) for z/OS.
Encrypting data at rest can be done several ways, by the application at the host server, in a SAN-based switch, or at the storage system itself. I presented how IBM Tivoli Storage Manager, the IBM SAN32B-E4 SAN switch, and various disk and tape devices accomplish this level of protection.
NAS @ IBM
Rich Swain, IBM Field Technical Sales Specialist for NAS solutions, provided an overview of IBM's NAS strategy and the three products: Scale-Out Network Attached Storage (SONAS), Storwize V7000 Unified, and N series.
IBM System Networking Convergence CEE/DCB/FCoE
Mike Easterly, IBM Global Field Marketing Manager for IBM System Networking, presented on Network convergence. He wants to emphasize that "Convergence is not just FCoE!" rather it is bringing together FCoE with iSCSI, CIFS, NFS and other Ethernet-based protocols. In his view, "All roads lead to Ethernet!"
There are a lot new standards that didn't exist a few years ago, such as PCI-SIG's Single Root I/O Virtualization [SR-IOV], Virtual Ethernet Port Aggregator [VEPA], and [VN-Tag], Data Center Bridging [DCB], Layer-2 Multipath [L2MP], and my favorite: Transparent Interconnect of Lots of Links [TRILL].
Last year, IBM acquired Blade Network Technologies (BNT), which was the company that made IBM BladeCenter's Advanced Management Module (AMM) and BladeCenter Open Fabric Manager (BOFM). BNT also makes Ethernet switches, so it has been merged with IBM's System Storage team, forming the IBM System Storage and Networking team. Most of today's 10GbE is either fiber optic, Direct Attach Copper (DAC) that supports up to 8.5 meter length cables, or 10GBASE-T which provides longer distances of twisted pair. IBM's DS3500 uses 10GBASE-T for its 10GbE iSCSI support.
Last month, IBM announced 40GbE! I missed that one. The IT industry also expects to deliver 100GbE by 2013. For now, these will be used as up-links between other switches, as most servers don't have the capacity to pump this much data through their buses. With 40GbE and 100GbE, it would be hard to ignore Ethernet as the common network standard to drive convergence.
Fibre Channel, such as FCP and FICON, are still the dominant storage networking technology, but this is expected to peak around 2013 and start declining thereafter in favor of iSCSI, NAS and FCoE technologies. Already the enhancements like "Priority-based Flow Control" made to Ethernet to support FCoE have also helped out iSCSI and NAS deployments as well.
The iSCSI protocol is being used with Microsoft Exchange, PXE Boot, Server virtualization hypervisors like VMware and Hyper-V, as well as large Database and OLTP. IBM's SVC, Storwize V7000, XIV, DS5000, DS3500 and N series all support iSCSI.
IBM's [RackSwitch] family of products can help offload traffic at $500 per port, compared to traditional $2000 per port for IBM SAN32B or Cisco Nexus5000 converged top-of-rack switches.
IBM's System Networking strategy has two parts. For Ethernet, offer its own IBM System Networking product line as well as continue its partnership with Juniper Networks. For Fibre Channel and FCoE, continue strategic partnerships with Brocade and Cisco. IBM will lead the industry, help drive open standards to adopt Converged Enhanced Ethernet (CEE), provide flexibility and validate data center networking solutions that work end-to-end.
Well, it's Tuesday, and you know what that means... IBM announcements!
In today's environment, clients expect more from their storage, and from their storage provider. The announcements span the gamut, from helping to use Business Analytics to analyze Big Data for trends, insights and patterns, to managing private, public and hybrid cloud environments, all with systems that are optimized for their particular workloads.
There are over a dozen different announcements, so I will split these up into separate posts. Here is part 1.
IBM Scale Out Network Attach Storage (SONAS) R1.3
I have covered [IBM SONAS] for quite some time now. Based on IBM's General Parallel File System (GPFS), this integrated system combines servers, storage and software into a fully functional scale-out NAS solution that support NFS, CIFS, FTP/SFTP, HTTP/HTTPS, and SCP protocols. IBM continues its technical leadership in the scale-out NAS marketplace with new hardware and software features.
The hardware adds new disk options, with 900GB SAS 15K RPM drives, and 3TB NL-SAS 7200 RPM drives. These come in 4U drawers of 60 drives each, six ranks of ten drives each. So, with the high-performance SAS drives that would be about 43TB usable capacity per drawer, and with the high-capacity NL-SAS drives about 144TB usable. You can have any mix of high-performance drawers and high-capacity drawers, up to 7200 drives, for a maximum usable capacity of 17PB usable (21PB for those who prefer it raw). This makes it the largest commercial scale-out NAS in the industry. This capacity can be made into one big file system, or divided up to 256 smaller file systems.
In addition to snapshots of each file system, you can divide the file system up into smaller tree branches and snapshot these independently as well. The tree branches are called fileset containers. Furthermore, you can now make writeable clones of individual files, which provides a space-efficient way to create copies for testing, training or whatever.
Performance is improved in many areas. The interface nodes now can support a second dual-port 10GbE, and replication performance is improved by 10x.
SONAS supports access-based enumeration, which means that if there are 100 different subdirectories, but you only have authority to access five of them, then that's all you see, those five directories. You don't even know the other 95 directories exist.
I saved the coolest feature for last, it is called Active Cloud Engine™ that offers both local and global file management. Locally, Active Cloud Engine placement rules to decide what type of disk a new file should be placed on. Management rules that will move the files from one disk type to another, or even migrates the data to tape or other externally-managed storage! A high-speed scan engine can rip through 10 million files per node, to identify files that need to be moved, backed up or expired.
Globally, Active Cloud Engine makes the global namespace truly global, allowing the file system to span multiple geographic locations. Built-in intelligence moves individual files to where they are closest to the users that use them most. This includes an intelligent push-over-WAN write cache, on-demand pull-from-WAN cache for reads, and will even pre-fetch subsets of files.
No other scale-out NAS solution from any other storage vendor offers this amazing and awesome capability!
IBM® Storwize® V7000
Last year, we introduced the [IBM Storwize V7000], a midrange disk system with block-level access via FCP and iSCSI protocols. The 2U-high control enclosure held two cannister nodes, a 12-drive or 24-drive bay, and a pair of power-supply/battery UPS modules. The controller could attach up to nine expansion enclosures for more capacity, as well as virtualize other storage systems. This has been one of our most successful products ever, selling over 100PB in the past 12 months to over 2,500 delighted customers.
The 12-drive enclosure now supports both 2TB and 3TB NL-SAS drives. The 24-drive enclosures support 200/300/400GB Solid-State Drives (SSD), 146 and 300GB 15K RPM drives, 300/450/600GB 10K RPM drives, and a new 1TB NL-SAS drive option. For those who want to set up "Flash-and-Stash" in a single 2U drawer, now you can combine SSD and NL-SAS in the 24-drive enclosure! This is the perfect platform for IBM's Easy Tier sub-LUN automated tiering. IBM's Easy Tier is substantially more powerful and easier to use than EMC's FAST-VP or HDS's Dynamic Tiering.
Last week, at Oracle OpenWorld, there were various vendors hawking their DRAM/SSD-only disk systems, including my friends at Texas Memory Systems, Pure Storage, and Violin Memory Systems. When people came to the IBM booth to ask what IBM offers, I explained that both the IBM DS8000 and the Storwize V7000 can be outfitted in this manner. With the Storwize V7000, you can buy as much or little SSD as you like. You do not have to buy these drives in groups of 8 or 16 at a time.
The Storwize V7000 is the sister product of the IBM SAN Volume Controller, so you can replicate between one and the other. I see two use cases for this. First, you might have a SVC at a primary location, and decide to replicate just the subset of mission-critical production data to a remote location, and use the Storwize V7000 as the target device. Secondly, you could have three remote or branch offices (ROBO) that replicate to a centralized data center SAN Volume Controller.
Lastly, like the SVC, the Storwize V7000 now supports clustering so that you can now combine multiple control enclosures together to make a single system.
IBM® Storwize® V7000 Unified
Do you remember how IBM combined the best of SAN Volume Controller, XIV and DS8000 RAID into the Storwize V7000? Well, IBM did it again, combining the best of the Storwize V7000 with the common NAS software base developed for SONAS into the new "Storwize V7000 Unified".
You can upgrade your block-only Storwize V7000 into a file-and-block "Storwize V7000 Unified" storage system. This is a 6U-high system, consisting of a pair of 2U-high file modules connected to a standard 2U-high control enclosure. Like the block-only version, the control enclosure can attach up to nine expansion enclosures, as well as all the same support to virtualize external disk systems. The file modules combine the management node, interface node and storage node functionality that SONAS R1.3 offers.
What exactly does that mean for you? In addition to FCP and iSCSI for block-level LUNs, you can carve out file systems that support NFS, CIFS, FTP/SFTP, HTTP/HTTPS, and SCP protocols. All the same support as SONAS for anti-virus checking, access-based enumeration, integrated TSM backup and HSM functionality to migrate data to tape, NDMP backup support for other backup software, and Active Cloud Engine's local file management are all included!
IBM SAN Volume Controller V6.3
The SAN Volume Controller [SVC] increases its stretched cluster to distances up to 300km. This is 3x further than EMC's VPLEX offering. This allows identical copies of data to be kept identical in both locations, and allows for Live Partition Mobility or VMware vMotion to move workloads seamlessly from one data center to another. Combining two data centers with an SVC stretch cluster is often referred to as "Data Center Federation".
The SVC also introduces a low-bandwidth option for Global Mirror. We actually borrowed this concept from our XIV disk system. Normally, SVC's Global Mirror will consume all the bandwidth it can to keep the destination copy of the data within a few seconds of currency behind the source copy. But do you always need to be that current? Can you afford the bandwidth requirements needed to keep up with that? If you answered "No!" to either of these, then the low-bandwidth option is you. Basically, a FlashCopy is done on the source copy, this copy is then sent over to the destination, and a FlashCopy is made of that. The process is then repeated on a scheduled basis, like every four hours. This greatly reduces the amount of bandwidth required, and for many workloads, having currency in hours, rather than seconds, is good enough.
I am very excited about all these announcements! It is a good time to be working for IBM, and look forward to sharing these exciting enhancements with clients at the Tucson EBC.
Over on the Tivoli Storage Blog, there is an exchange over the concept of a "Storage Hypervisor". This started with fellow IBMer Ron Riffe's blog post [Enabling Private IT for Storage Cloud -- Part I], with a promise to provide parts 2 and 3 in the next few weeks. Here's an excerpt:
"Storage resources are virtualized. Do you remember back when applications ran on machines that really were physical servers (all that “physical” stuff that kept everything in one place and slowed all your processes down)? Most folks are rapidly putting those days behind them.
In August, Gartner published a paper [Use Heterogeneous Storage Virtualization as a Bridge to the Cloud] that observed “Heterogeneous storage virtualization devices can consolidate a diverse storage infrastructure around a common access, management and provisioning point, and offer a bridge from traditional storage infrastructures to a private cloud storage environment” (there’s that “cloud” language). So, if I’m going to use a storage hypervisor as a first step toward cloud enabling my private storage environment, what differences should I expect? (good question, we get that one all the time!)
The basic idea behind hypervisors (server or storage) is that they allow you to gather up physical resources into a pool, and then consume virtual slices of that pool until it’s all gone (this is how you get the really high utilization). The kicker comes from being able to non-disruptively move those slices around. In the case of a storage hypervisor, you can move a slice (or virtual volume) from tier to tier, from vendor to vendor, and now, from site to site all while the applications are online and accessing the data. This opens up all kinds of use cases that have been described as “cloud”. One of the coolest is inter-site application migration.
A good storage hypervisor helps you be smart.
Application owners come to you for storage capacity because you’re responsible for the storage at your company. In the old days, if they requested 500GB of capacity, you allocated 500GB off of some tier-1 physical array – and there it sat. But then you discovered storage hypervisors! Now you tell that application owner he has 500GB of capacity… What he really has is a 500GB virtual volume that is thin provisioned, compressed, and backed by lower-tier disks. When he has a few data blocks that get really hot, the storage hypervisor dynamically moves just those blocks to higher tier storage like SSD’s. His virtual disk can be accessed anywhere across vendors, tiers and even datacenters. And in the background you have changed the vendor storage he is actually sitting on twice because you found a better supplier. But he doesn’t know any of this because he only sees the 500GB virtual volume you gave him. It’s 'in the cloud'."
"Let’s start with a quick walk down memory lane. Do you remember what your data protection environment looked like before virtualization? There was a server with an operating system and an application… and that thing had a backup agent on it to capture backup copies and send them someplace (most likely over an IP network) for safe keeping. It worked, but it took a lot of time to deploy and maintain all the agents, a lot of bandwidth to transmit the data, and a lot of disk or tapes to store it all. The topic of data protection has modernized quite a bit since then.
Fast forward to today. Modernization has come from three different sources – the server hypervisor, the storage hypervisor and the unified recovery manager. The end result is a data protection environment that captures all the data it needs in one coordinated snapshot action, efficiently stores those snapshots, and provides for recovery of just about any slice of data you could want. It’s quite the beautiful thing."
At this point, you might scratch your head and ask "Does this Storage Hypervisor exist, or is this just a theoretical exercise?" The answer of course is "Yes, it does exist!" Just like VMware offers vSphere and vCenter, IBM offers block-level disk virtualization through the SAN Volume Controller(SVC) and Storwize V7000 products, with a full management support from Tivoli Storage Productivity Center Standard Edition.
SVC has supported every release of VMware since the 2.5 version. IBM is the leading reseller of VMware, so it makes sense for IBM and VMware development to collaborate and make sure all the products run smoothly together. SVC presents volumes that can be formatted for VMFS file system to hold your VMDK files, accessible via FCP protocol. IBM and VMware have some key synergies:
Management integration with Tivoli Storage Productivity Center and VMware vCenter plug-in
VAAI support: Hardware-assisted locking, hardware-assisted zeroing, and hardware-assisted copying. Some of the competitors, like EMC VPLEX, don't have this!
Space-efficient FlashCopy. Let's say you need 250 VM images, all running a particular level of Windows. A boot volume of 20GB each would consume 5000GB (5 TB) of capacity. Instead, create a Golden Master volume. Then, take 249 copies with space-efficient FlashCopy, which only consumes space for the modified portions of the new volumes. For each copy, make the necessary changes like unique hostname and IP address, changing only a few blocks of data each. The end result? 250 unique VM boot volumes in less than 25GB of space, a 200:1 reduction!
Support for VMware's Site Recovery Manager using SVC's Metro Mirror or Global Mirror features for remote-distance replication.
Data center federation. SVC allows you to seamlessly do vMotion from one datacenter to another using its "stretched cluster" capability. Basically, SVC makes a single image of the volume available to both locations, and stores two physical copies, one in each location. You can lose either datacenter and still have uninterrupted access to your data. VMware's HA or Fault Tolerance features can kick in, same as usual.
But unlike tools that work only with VMware, IBM's storage hypervisor works with a variety of server virtualization technologies, including Microsoft Hyper-V, Xen, OracleVM, Linux KVM, PowerVM, z/VM and PR/SM. This is important, as a recent poll on the Hot Aisle blog indicates that [44 percent run 2 or more server hypervisors]!
Join the conversation! The virtual dialogue on this topic will continue in a [live group chat] this Friday, September 23, 2011 from 12 noon to 1pm EDT. Join me and about 20 other top storage bloggers, key industry analysts and IBM Storage subject matter experts to discuss storage hypervisors and get questions answered about improving your private storage environment.
Continuing my coverage of the [IBM System Storage Technical University 2011], I participated in the storage free-for-all, which is a long-time tradition, started at SHARE User Group conference, and carried forward to other IT conferences. The free-for-all is a Q&A Panel of experts to allow anyone to ask any question. These are sometimes called "Birds of a Feather" (BOF). Last year, we had two: one focused on Tivoli Storage software, and the second to cover storage hardware. This year, we had two, one for System x called "Ask the eXperts", and one for System Storage called "Storage Free-for-All". This post covers the latter.
(Disclaimer: Do not shoot the messenger! We had a dozen or more experts on the panel, representing System Storage hardware, Tivoli Storage software, and Storage services. I took notes, trying to capture the essence of the questions, and the answers given by the various IBM experts. I have spelled out acronyms and provided links to relevant materials. The answers from individual IBMers may not reflect the official position of IBM management. Where appropriate, my own commentary will be in italics.)
You are in the wrong session! Go to "Ask the eXperts" session next door!
The TSM GUI sucks! Are there any plans to improve it?
Yes, we are aware that products like IBM XIV have raised the bar for what people expect from graphical user interfaces. We have plans to improve the TSM GUI. IBM's new GUI for the SAN Volume Controller and Storwize V7000 has been well-received, and will be used as a template for the GUIs of other storage hardware and software products. The GUI uses the latest HTML5, Dojo widgets and AJAX technologies, eliminating Java dependencies on the client browser.
Can we run the TSM Admin GUI from a non-Windows host?
IBM has plans to offer this. Most likely, this will be browser-based, so that any OS with a modern browser can be used.
As hard disk drives grow larger in capacity, RAID-5 becomes less viable. What is IBM doing to address this?
IBM is aware of this problem. IBM offers RAID-DP on the IBM N series, RAID-X on the IBM XIV, and RAID-6 on its other disk systems.
TPC licensing is outrageous! What is IBM going to do about it?
About 25 percent of DS8000 disk systems have SSD installed. Now that IBM DS8000 Easy Tier supports "any two" tiers, roughly 50 percent of DS8000 now have Easy Tier activated. No idea on how Easy Tier has been adopted on SVC or Storwize V7000.
We have an 8-node SVC cluster, should we put 8 SSD drives into a single node-pair, or spread them out?
We recommend putting a separate Solid-State Drive in each SVC node, with RAID-1 between nodes of a node-pair. By separating the SSD across I/O groups, you can reduce node-to-node traffic.
How well has SVC 6.2 been adopted?
The inventory call-home data is not yet available. The only SVC hardware model that does not support this level of software was the 2145-4F2 introduced in 2003. Every other model since then can be updated to this level.
Will IBM offer 600GB FDE drives for the IBM DS8700?
Currently, IBM offers 300GB and 450GB 15K RPM drives with the Full-Disk Encryption (FDE) capability for the DS8700, and 450GB and 600GB 10K RPM drives with FDE for the IBM DS8800. IBM is working with its disk suppliers to offer FDE on other disk capacities, and on SSD and NL-SAS drives as well, so that all can be used with IBM Easy Tier.
Is there a reason for the feature lag between the Easy Tier capabilities of the DS8000, and that of the SVC/Storwize V7000?
We have one team for Easy Tier, so they implement it first on DS8000, then port it over to SVC/Storwize V7000.
Does it even make sense to have separate storage tiers, especially when you factor in the cost of SVC and TPC to make it manageable?
It depends! We understand this is a trade-off between cost and complexity. Most data centers have three or more storage tiers already, so products like SVC can help simplify interoperability.
Are there best practices for combining SVC with DS8000? Can we share one DS8000 system across two or more SVC clusters?
Yes, you can share one DS8000 across multiple SVC clusters. DS8000 has auto-restripe, so consider having two big extent pools. The queue depth is 3 to 60, so aim to have up to 60 managed disks on your DS8000 assigned to SVC. The more managed disks the better.
The IBM System Storage Interopability Center (SSIC) site does not seem to be designed well for SAN Volume Controller.
Yes, we are aware of that. It was designed based on traditional Hardware Compatability Lists (HCL), but storage virtualization presents unique challenges.
How does the 24-hour learning period work for IBM Easy Tier? We have batch processing that runs from 2am to 8am on Sundays.
You can have Easy Tier monitor across this batch job window, and turn Easy Tier management between tiers on and off as needed.
Now that NetApp has acquired LSI, is the DS3000 still viable?
Yes, IBM has a strong OEM relationship with both NetApp and LSI, and this continues after the acquisition.
If have managed disks from a DS8000 multi-rank extent pool assigned to multiple SVC clusters, won't this affect performance?
Yes, possibly. Keep managed disks on seperate extent pools if this is a big concern. A PERL script is available to re-balance SVC striped volumes as needed after these changes.
Is the IBM [TPC Reporter] a replacement for IBM Tivoli Storage Productivity Center?
No, it is software, available at no additional charge, that provides additional reporting to those who have already licensed Tivoli Storage Productivity Center 4.1 and above. It will be updated as needed when new versions of Productivity Center are released.
We are experiencing lots of stability issues with SDD, SDD-PCM and SDD-DSM multipathing drivers. Are these getting the development attention they deserve?
IBM's direction is to shift toward native OS-based multipathing drivers.
Is anyone actually thinking of deploying public cloud storage in the near-term?
A few hands in the audience were raised.
None of the IBM storage devices seem to have [REST API]. Cloud storage providers are demanding this. What are IBM plans?
IBM plans to offer REST on SONAS. IBM uses SONAS internally for its own cloud storage offerings.
If you ask a DB2 specialist, an AIX specialist, and a System Storage specialist, on how to configure System p and System Storage for optimal performance, you get three different answers. Are there any IBMers who are cross-functional that can help?
Yes, for example, Earl Jew is an IBM Field Technical Support Specialist (FTSS) for both System p and Storage, and can help you with that.
Both Oracle and Microsoft recommend RAID-10 for their applications.
Don't listen to them. Feel free to use RAID-5, RAID-6 or RAID-X instead.
Resizing SVC source volumes forces ongoing FlashCopy or Metro Mirror relatiohships to be stopped. Does IBM plan to address this?
Currently, you have to stop, resize both source and target, then start the relationship again. Consider getting IBM Tivoli Storage Productivity Center for Replication (TPC-R).
IBM continues to support this for exising clients. For new deployments, IBM offers SONAS and the Information Archive (IA).
When will I be able to move SVC volumes between I/O groups?
You can today, but it is disruptive to the operating system. IBM is investigating making this less disruptive.
Will XIV ever support the mainframe?
It does already, with support for both Linux and z/VM today. For VSE support, use SVC with XIV. For those with the new zBX extension, XIV storage can be used with all of the POWER and x86-based operating systems supported. IBM has no plans to offer direct FICON attachment for z/OS or z/TPF.
Not a question - Kudos to the TSM and ProtecTIER team in supporting native IP-based replication!
When will IBM offer POWER-based models of the XIV, SVC and other storage devices?
IBM's decision to use industry-standard x86 technology has proven quite successful. However, IBM re-looks at this decision every so many years. Once again, the last iteration determined that it was not worth doing. A POWER-based model might not beat the price/performance of current x86 models, and maintaining two separate code bases would hinder development of new innovations.
We have both System i and System z, what is IBM doing to address the fact that PowerHA and GDPS are different?
IBM TPC-R has a service offering extension to support "IBM i" environments. GDPS plans to support multi-platform environments as well.
This was a great interactive session. I am glad everyone stayed late Thursday evening to participate in this discussion.
I always try to catch a session from Jim Blue, who works in our "SAN Central" center of competency team. This session was a long list of useful hints and tips, based on his many years of experience helping clients.
SAN Zoning works by inclusion, limiting the impact of failing devices. The best approach is to zone by individual initiator port. The default policy for your SAN zoning should be "deny".
Ports should be named to identify who, what, where and how.
While many people know not to mix both disk and tape devices on the same HBA, Jim also recommends not mixing dissimilar disks, test and production, FCP and FICON.
The sweet spot is FOUR paths. Too many paths can impact performance.
When making changes to redundant fabrics, make changes to the first fabric, then allow sufficient time before making the same changes to the other fabric.
Use software tools like Tivoli Storage Productivity Center (Standard Edition) to validate all changes to your SAN fabric.
Do not mix 62.5 and 50.0 micron technology.
Use port caps to disable inactive ports. In one amusing anecdote, he mention that an uncovered port was hit by sunlight every day, sending error messages that took a while to figure out.
Save your SAN configuration to non-SAN storage for backup
Consider firmware about two months old to be stable
Rule of thumb for estimating IOPS: 75-100 IOPS per 7200 RPM drive, 120-150 IOPS per 10K RPM drive, and 150-200 IOPS per 15K RPM drive.
Decide whether your shop is just-in-time or just-in-case provisioning. Just-in-time gets additional capacity on demand as needed, and just-in-case over-provisions to avoid scrambling last minute.
Avoid oversubscribing your inter-switch links (ISL). Aim for around 7:1 to 10:1 ratio.
Don't go cheap on bandwidth between sites for long-distance replication
Next Generation Network Fabrics - Strategy and Innovations
Mike Easterly, IBM Director of Global Field Marketing, presented IBM System Networking strategy, in light of IBM's recent acquisition of Blade Network Technologies (BNT). BNT is used in 350 of the Fortune 500 companies, and is ranked #2 behind Cisco in sales of non-core Ethernet switches (based on number of units sold).
Based on a recent survey, companies are upgrading their Ethernet networks for a variety of reasons:
56 percent for Live Partition Mobility and VMware Vmotion
45 percent for integrated compute stacks, like IBM CloudBurst
43 percent for private, public and hybrid cloud computing deployments
40 percent for network convergences
Many companies adopt a three-level approach, with core directors, distribution switches, and then access switches at the edge that connect servers and storage devices. IBM's BNT allows you to flatten the network to lower latency by collapsing the access and distribution levels into one.
IBM's strategy is to focus on BNT for the access/distribution level, and to continue its strategic partnerships for the core level.
IBM BNT provides better price/performance and lower energy consumption. To help with hot-aisle/cold-aisle rack deployments, IBM BNT provides both F and R models. F models have ports on the front, and R models have ports in the rear.
IBM BNT supports virtual fabric and HW-offload iSCSI traffic, and future-enabled for FCoE. Support for TRILL (transparent interconnect of lots of links) and OpenFlow will be implemented through software updates to the switches.
While Cisco Nexus 1000v is focused on VMware Enterprise Plus, IBM BNT's VMready works with VMware, Hyper-V, Linux KVM, XEN, OracleVM, and PowerVM. This allows single pane of management of VMready and ESX vSwitches.
In preparation for Converged Enhanced Ethernet (CEE), IBM BNT will provide full 40GbE support sometime next year, and offer switches that support 100GbE uplinks. IBM offers extended length cables, including passive SFP+ DAC at 8.5 meters, and 10Gbase-T Cat7 cables up to 100 meters.
Inter-datacenter Workload Mobility with VMware vSphere and SAN Volume Controller (SVC)
This session was co-presented between Bill Wiegand, IBM Advanced Technical Services, and Rawley Burbridge, IBM VMware and midrange storage consultant. IBM is the leader in storage virtualization product (SVC), and is the leading reseller of VMware.
Like MetroCluster on IBM N series, or EMC's VPLEX Metro, the IBM SAN Volume Controller can support a stretched cluster across distance that allows virtual machines to move seamlessly from one datacenter to another. This is a feature IBM introduced with SVC 5.1 back in 2009. This can be used for PowerVM Live Partition Mobility, VMware vMotion, and Hyper-V Quick Migration.
SVC stretched cluster can help with both Disaster Avoidance and Disaster Recovery. For Disaster Avoidance, in anticipation of an outage, VMs can be moved to the secondary datacenter. For Disaster Recover, additional automation, such as VMware High Availability (HA) is needed to restart the VMs at the secondary datacenter.
IBM stretched cluster is further improved with a feature called Volume Mirroring (formerly vDisk Mirroring) which creates two physical copies of one logical volume. To the VMware ESX hosts, there is only one volume, regardless of which datacenter it is in. The two physical copies can be on any kind of managed disk, as there is no requirement or dependency of copy services on the back-end storage arrays.
Another recent improvement is the idea of spreading the three quorum disks to three different locations or "failure domains". One in each data center, and a third one in a separate building, somewhere in between the other two, perhaps.
Of course, there are regional disasters that could affect both datacenters. For this reason, SVC stretched cluster volumes can be replicated to a third location up to 8000 km away. This can be done with any back-end disk arrays, as again there is not requirement for copy services from the managed devices. SVC takes care of it all.
Networking is going to be very important for a variety of transformational projects going forward in the next five years.
I gotten several emails expressing worry that I have fallen off the face of th earth. The last two weeks have been educational and eye-opening for me. I can't provide details in my blog, so I will just say that it involved government agencies that IBM refers to as "dark accounts", and that I am now back safely in the USA. Between adjusting to time zone differences, ridiculously long hours, and restricted access to the internet, I was unable to blog lately.
Instead, I will resume my coverage of the [IBM System Storage Technical University 2011]. The "Solutions Expo" runs Monday evening through Wednesday lunch. This is a chance for people to explore all the solutions that are part of IBM's large "eco-system" for IBM System storage and System x products. There were several sponsors for this event.
As is often the case at these conferences, the various booths hand out fun items. The hot items this year were tie-dyed tee-shirts from Qlogic, and propeller beanies from the IBM rack and power systems team. Here is Amanda, one of the bartenders showing off the latter.
After the expo on Tuesday night, my friends at [Texas Memory Systems] held an after-party. Unlike the pens, tee-shirts and keychains at the Expo, these guys had a raffle for real storage products. Here is Erik Eyberg handing out a RamSan PCIe card, valued at $14,000 or so. IBM recently certified the TMS RamSan as External SSD storage for the IBM SAN Volume Controller (SVC). The SVC can optimize performance using this for automated sub-LUN tiering with the IBM System Storage Easy Tier feature.
Jim is an IBM Fellow for IBM Systems and Technology Group. There are only 73 IBM Fellows currently working for IBM, and this is the highest honor IBM can bestow on an employee. He has been working with IBM since 1968.
He is tasked with predicting the future of IT, and help drive strategic direction for IBM. Cost pressures, requirements for growth, accelerating innovation and changing business needs help influence this direction.
IBM's approach is to integrate four different "IT building blocks":
Scale-up Systems, like the IBM System Storage DS8000 and TS3500 Tape Library
Resource Pools, such as IBM Storage Pools formed from managed disks by IBM SAN Volume Controller (SVC)
Integrated stacks and appliances, integrated software and hardware stacks, from Storwize V7000 to full rack systems like IBM Smart Analytics Server or CloudBurst.
Mobility of workloads and resources requires unified end-to-end service management. Fortunately, IBM is the #1 leader in IT Service Management solutions.
Jim addressed three myths:
Myth 1: IT Infrastructures will be homogenous.
Jim feels that innovations are happening too rapidly for this to ever happen, and is not a desirable end-goal. Instead, a focus to find the right balance of the IT building blocks might be a better approach.
Myth 2: All of your problems can be solved by replacing everything with product X.
Jim feels that the days of "rip-and-replace" are fading away. As IBM Executive Steve Mills said, "It isn't about the next new thing, but how well new things integrate with established applications and processes."
Myth 3: All IT will move to the Cloud model.
Jim feels a substantial portion of IT will move to the Cloud, but not all of it. There will always be exceptions where the old traditional ways of doing things might be appropriate. Clouds are just one of the many building blocks to choose from.
Jim's focus lately has been finding new ways to take advantage of virtualization concepts. Server, storage and network virtualization are helping address these challenges through four key methods:
Sharing - virtualization that allows a single resource to be used by multiple users. For example, hypervisors allow several guest VM operating systems share common hardware on a single physical server.
Aggregation - virtualization that allows multiple resources to be managed as a single pool. For example, SAN Volume Controller can virtualize the storage of multiple disk arrays and create a single storage pool.
Emulation - virtualization that allows one set of resources to look and feel like a different set of resources. Some hypervisors can emulate different kinds of CPU processors, for example.
Insulation - virtualization that hides the complexity from the end-user application or other higher levels of infrastructure, making it easier to make changes of the underlying managed resources. For example, both SONAS and SAN Volume Controller allow disk capacity to be removed and replaced without disruption to the application.
In today's economy, IT transformation costs must be low enough to yield near-term benefits. The long-term benefits are real, but near-term benefits are needed for projects to get started.
What set's IBM ahead of the pack? Here was Jim's list:
100 Years of Innovation, including being the U.S. Patent leader for the last 18 years in a row
IBM's huge investment in IBM Research, with labs all over the globe
Leadership products in a broad portfolio
Workload-optimized designs with integration from middleware all the way down to underlying hardware
Comprehensive management software for IBM and non-IBM equipment
Clod is an IBM Distinguished Engineer and Chief Technical Strategist for IBM System Storage. His presentation focused on trends and directions in the IT storage industry. Clod started with five workload categories:
To address these unique workload categories, IBM will offer workload-optimized systems. The four drivers on the design for these are performance, efficiency, scalability, and integration. For example, to address performance, companies can adopt Solid-State Drives (SSD). Unfortunately, these are 20 times more expensive dollar-per-GB than spinning disk, and the complexity involved in deciding what data to place on SSD was daunting. IBM solved this with an elegant solution called IBM System Storage Easy Tier, which provides automated data tiering for IBM DS8000, SAN Volume Controller (SVC) and Storwize V7000.
For scalability, IBM has adopted Scale-Out architectures, as seen in the XIV, SVC, and SONAS. SONAS is based on the highly scalable IBM General Parallel File System (GPFS). File systems are like wine, they get better with age. GPFS was introduced 15 years ago, and is more mature than many of the other "scalable file systems" from our competition.
Areal Density advancements on Hard Disk Drives (HDD) are slowing down. During the 1990s, the IT industry enjoyed 60 to 100 percent annual improvement in areal density (bits per square inch). In the 2000s, this dropped to 25 to 40 percent, as engineers are starting to hit various physical limitations.
Storage Efficiency features like compression have been around for a while, but are being deployed in new ways. For example, IBM invented WAN compression needed for Mainframe HASP. WAN compression became industry standard. Then IBM introduced compression on tape, and now compression on tape is an industry standard. ProtecTIER and Information Archive are able to combine compression with data deduplication to store backups and archive copies. Lastly, IBM now offers compression on primary data, through the IBM Real-Time Compression appliance.
For the rest of this decade, IBM predicts that tape will continue to enjoy (at least) 10 times lower dollar-per-GB than the least expensive spinning disk. Disk and Tape share common technologies, so all of the R&D investment for these products apply to both types of storage media.
For integration, IBM is leading the effort to help companies converge their SAN and LAN networks. By 2015, Clod predicts that there will be more FCoE purchased than FCP. IBM is also driving integration between hypervisors and storage virtualization. For example, IBM already supports VMware API for Array Integration (VAAI) in various storage products, including XIV, SVC and Storwize V7000.
Lastly, Clod could not finish a presentation without mentioning Cloud Computing. Cloud storage is expected to grow 32 percent CAGR from year 2010 to 2015. Roughly 10 percent of all servers and storage will be in some type of cloud by 2015.
As is often the case, I am torn between getting short posts out in a timely manner versus spending some more time to improve the length and quality of information, but posted much later. I will spread out the blog posts in consumable amounts throughout the next week or two, to achieve this balance.
Maria Boonie is the IBM Director for IBM Worldwide Training and Technical Conferences. She indicated that there were 1500 attendees this week crossing both the System Storage and System x conferences at this hotel. There are 35 vendors that have sponsored this event, and they will be at the "Solutions Center" being held Monday through Wednesday this week.
She took this opportunity to plug IBM's latest education offerings, including Guaranteed-to-Run implementation classes, and Instructor-Led Online (ILO) technical classes.
Brian Truskowski is IBM General Manager for System Storage and Networking. I used to directly report to him in a previous role, and a few years ago he used to be the IBM CIO that helped with IBM's internal IT transformation.
Brian indicates that the previous approach to growth was to "Just Buy More", but this has some unintended consequences. He argued that companies need to adopt one or more of the following approaches to growth:
Stop storing so much - reduce data footprint using storage efficiency capabilities like data deduplication and compression
Store more with what is already on the floor - improve storage utilization with technologies like storage virtualization and thin provisioning
Move data to the right place - implement automated tiering, such as "Flash & Stash" between Solid-state drives and spinning disk, and/or Information Lifecycle Management (ILM) between disk and tape. Studies at some clients have found over 70 percent of data has not beed touched in the last 90 days
This time of dramatic change is the result of a "perfect storm" of influences, including the rising costs and risks associated with losing data, the increased need to index and search data, the desire for "Business Analytics", and the expectation for 100 percent up-time. This is driving IBM to offer hyper-efficient backup, Continuous Data Availability, and Smart Archive solutions.
The case study of SPRINT is a good example. SPRINT is a Telecommunications provider for cell phone users. They were challenged with 35 percent utilization, 165 storage arrays from six different vendors, and an expected 100 percent increase in their IT maintenance costs. After implementing IBM SAN Volume Controller (SVC) and Tivoli Storage Productivity Center (TPC) to manager 2.9 PB of data, SPRINT increased their utilization to 82 percent, reduced down to 70 storage arrays from only three vendors, and reduced their maintenance costs by 57 percent. Today, SPRINT now manages over 5 PB of data with SVC and TPC, have reduced their power and cooling by 3.5 million KWh, representing $320,000 USD in savings.
Roland Hagan is the IBM Vice President for the System x server platform. He talked about the "IT Conundrum" that represents a vicious cycle of "IT Sprawl", "Untrusted Data" and "Inflexible IT" that seem to feed each other. IBM is trying to change behavior, from thinking and dealing with physical boxes representing servers, storage and network gear, to a more holistic view focused on workloads, shared resource pools, independent scaling, and automated management.
IBM is leading the server marketplace, in part because of clever things IBM is doing, especially in developing the eX5 chipset that surrounds x86 commondity processors, and in part because of actions or decisions the competition have taken:
It doesn't break IBM's heart that Oracle decided to drop software support of their database on Itanium, which focued entirley against HP. Oracle runs on IBM servers better than Oracle/Sun or HP servers today, so it does not impact us, other than IBM has had a lot of people leaving HP to switch over to IBM.
HP has taken on a new CEO and reduced their R&D budget, causing them to be late-to-market on some of their offerings.
Dell continues to focus on the small and medium sized customer, and have not really broken into the "Enterprise".
Newcomer Cisco has some great technology that only seems to be adoptable in "Green Field" situations, as it does not integrate well with existing data center infrastructures.
The combination of ex5 chip-set architecture, Max5 memory expansion capabilities and Virtual Network Interface Cards (NICs), provide for a very VM-aware platform. For those who are not ready to fully adopt an integrated stack like IBM CloudBurst, IBM offers the Tivoli Service Automation software on its own, and a new [IBM BladeCenter Foundation for Cloud] as stepping stones to get there.
There are certainly more attendees here than last year, which reflects either the change in location (Orlando, Florida rather than Washington DC) as well as the economic recovery. I'm looking forward to an excellent week!
Dan Galvan, IBM VP of Marketing for Storage, was the next speaker. With 300 billion emails being sent per day, 4.6 billion cell phones in the world, and 26 million MRIs per year, there is going to be a huge demand for file-based storage. In fact, a recent study found that file-based storage will grow at 60 percent per year, compared to 15 percent growth for block-based storage.
Dan positioned IBM's Scale-out Network Attached Storage (SONAS) as the big "C:" drive for a company. SONAS offers a global namespace, a single point of management, with the ability to scale capacity and performance tailored for each environment.
The benefits of SONAS are great. We can consolidate dozens of smaller NAS filers, we can virtualize files across different storage pools, and increase overall efficiency.
Powering advanced genomic research to cure cancer
The next speaker was supposed to be Bill Pappas, Senior Enterprise Network Storage Architect, Research Informatics at [St. Jude Children’s Research Hospital]. Unfortunately, St. Jude is near the flooding of the Mississippi river, and he had to stay put. An IBM team was able to capture his thoughts on video that was shown on the big screen.
Thanks to the Human Genome project, St. Jude is able to cure people. They see 5700 patients per year, and have an impressive 70 percent cure rate. The first genetic scan took 10 years, now the technology allows a genome to be mapped in about a week. Having this genomic information is making vast strides in healthcare. It is the difference of fishing in a river, versus putting a wide net to catch all the fish in the Atlantic ocean all at once.
Recently, St. Jude migrated 250 TB of files from other NAS to an IBM SONAS solution. The SONAS can handle a mixed set of workloads, and allows internal movement of data from fast disk, to slower high-capacity disk, and then to tape. SONAS is one of the few storage systems that supports a blended disk-and-tape approach, which is ideal for the type of data captured by St. Jude.
IBM's own IT transformation
Pat Toole, IBM's CIO, presented the internal transformation of IBM's IT operations. He started in 2002 in the midst of IBM's effort to restructure its process and procedures. They identified four major data sources: employee data, client data, product data, and financial data. They put a focus to understand outcomes and set priorities.
The result? A 3-to-1 payback on CIO investments. This allowed IBM to go from server sprawl to consolidated pooling of resources with the right levels of integration. In 1997, IBM had 15,000 different applications running across 155 separate datacenters. Today, they have reduced this down to 4,500 applications and 7 datacenters. Their goal is to reduce down to 2,225 applications by 2015. Of these, only 250 are mission critical.
Pat's priorities today: server and storage virtualization, IT service management, cloud computing, and data-centered consolidation. IBM runs its corporate business on the following amount of data:
9 PB of block-based storage, SVC and XIV
1 PB of file-based storage, SONAS
15 PB of tape for backup and archive
Pat indicated that this environment is growing 25 percent per year, and that an additional 70-85 PB relates to other parts of the business.
By taking this focused approach, IBM was able to increase storage utilization from 50 to 90 percent, and to cut storage costs by 50 percent. This was done through thin provisioning, storage virtualization and pooling.
Looking forward to the future, Pat sees the following challenges: (a) that 120,000 IBM employees have smart phones and want to connect them to IBM's internal systems; (b) the increase in social media; and (c) the use of business analytics.
After the last session, people gathered in the "Hall of the Universe" for the evening reception, featuring food, drinks and live music. It was a great day. I got to meet several bloggers in person, and their feedback was that this was a very blogger-friendly event. Bloggers were given the same level of access as corporate executives and industry analysts.
Down the street, in Times Square, IBM made it on the big board.
Continuous Data Availability
Jeanine Cotter, IBM VP for Data Center Services, started out with a video about Sabre. IBM developed this revolutionary airline reservation system to handle the huge volume of transactions. Today, 18 percent of organizations consider downtime unacceptable for their tier-1 applications, and 53 percent would be seriously impacted by an outage lasting an hour or more.
Eventually, companies cross the "Continuous Availability" threshold, the point where they discover that the possibility of downtime is too costly to ignore. IBM has clients using 3-site Metro/Global Mirror that can fail-over an entire data center in just five mouse clicks.
Jeanine also mentioned Euronics, which is using SAN Volume Controller's Stretched Cluster capability, which allows them to easily vMotion virtual guest images from one data center to another. SVC has had this capability for a while, but now, with full VMcenter plug-in and VAAI support, the capability is fully integrated with VMware.
A final example was a mid-sized University, they are using IBM Storwize V7000 with Metro Mirror. The primary location's Storwize V7000 manages Solid-state drives with Easy Tier. The secondary location's Storwize V7000 has high-capacity SATA drives and FlashCopy.
Customer Testimonial - University of Rochester Medical Center
Rick Haverty, Director of IT infrastructure at University of Rochester Medical Center [URMC] provided the next client testimonial. The mission of the URMC is to use science, education and technology to improve health. URMC gets over $400 million USD in NIH grants, which puts them around 23rd largest University-based academic medical centers in the country. They have over 900 doctors, general practice and specialists.
URMC has an IBM BlueGene supercomputer, a Cisco network over 45,000 ports, and over 7.5 million square feet of Wi-Fi wireless internet coverage. They have three datacenters. The first is 7500 square feet, the second is 6000 square feet, and the third is just 800 square feet to hold their "off-site tapes".
URMC has digitized all of their records, including Electronic Medical Records (EMR) system, medical dosage history, imaging "priors", calibration of infusion pumps, RFID monitoring, and even provide IT support while the patient is on the operating table. RFID monitoring ensures all of the refrigerators are keeping medications at the right temperature. A single failed refrigerator can lose $20,000 dollars worth of medication.
When is a good time for downtime? At URMC, they handle 90,000 Emergency Room vists per year, so the answer is never. When is the ER busiest? Monday morning. (not what I expected!)
URMC's EMR software (Epic) runs on clustered POWER7 servers, with DS8700 disk systems using Metro Mirror to secondary location. They also keep a third "shadow" POWER7 for read-only purposes, and a separate system that provides web-based read-only access. Finally, they have 90 stand-alone Personal Computers (PCs) that contain information for all the patients that have reservations this week, just in case all the other systems fail.
The exploding volume of data comes from medical imaging. For radiology (X-rays), each image is called a "study" takes 20-30 MB each, and they have 650,000 studies per year. This represents about 16TB storage per year, with 3 second response time access. These must be kept for 7 years since last view, or until the patient reaches the age of 18 years old, which ever is later.
But radiology is just one discipline. Healthcare has a whole bunch of "ologies". Another is "Pathology" which looks at cells between glass slides in a microscope. Each study consumes 10-20GB, and URMC does about 100,000 pathology studies per year, representing 150TB per year.
URMC has identified that they have 42 mission-critical applications. The data for these are stored on DS8000, XIV, Storwize V7000 and DS5000, all managed behind SAN Volume Controller.
Optimizing Storage Infrastructure for Growth and Innovation
This session started off with my former boss, Brian Truskowski, IBM General Manager of System Storage and Networking.
We've come a long way in storage. In 1973, the "Winchester Drive" was named after the famous Winchester 3030 rifle. The disk drive was planning to have two 30MB platters, hence the name. When it finally launched, it would have two 35MB platters, for a total raw capacity of 70MB.
Today, IBM announced the verison 6.2 of SAN Volume Controller with support for 10GbE iSCSI. Since 2003, IBM has sold over 30,000 SAN Volume Controllers. An SVC cluster can now manage up to 32PB of disk storage.
IBM also announced new 4TB tape drive (TS1140), LTFS Library Edition, the TS3500 Library Connector, improved TS7600 and TS7700 virtual tape libraries, enhanced Information Archive for email, files and eDiscovery, new Storwize V7000 hardware, new Storwize Rapid Application bundles, new firmware for SONAS and DS8000 disk systems, and Real-Time Compression support for EMC disk systems. I plan to cover each of these in follow-on posts, but if you can't wait, here are [links to all the announcements].
Customer Testimonial - CenterPoint Energy
"CenterPoint is transforming its business from being an energy distribution company that uses technology, to a technology company that distributes energy."
-- Dr. Steve Pratt, CTO of CenterPoint Energy
The next speaker was Dr. Steve Pratt is CTO of [CenterPoint Energy]. CenterPoint is 110 years old (older than IBM!) energy company that is involved in electricity, gasoline distribution, and natural gas pipeline. CenterPoint serves Houston, Texas (the fourth largest city in the USA) and surrounding area.
CenterPoint are transforming to a Smart Grid involving smart meters, and this requires the best IT infrastructure you can buy, including IBM DS8000, XIV and SAN Volume Controller disk systems, IBM Smart Analytics System, Stream Analytics, IBM Virtual Tape Library, IBM Tivoli Storage Manager, and IBM Tivoli Storage Productivity Center.
Dr. Pratt has seen the transition of information over the years:
Data Structure, deciding how to code data to record it in a structured manner
Information Reporting, reporting to upper management what happened
Intelligence Aggregation, finding patterns and insight from the data
Predictive Analytics, monitoring real-time data to take pro-active steps
Autonomics, where automation and predictive analysis allows the system to manage itself
What does the transition to a Smart Grid mean for their storage environment? They will go from 80,000 meter reads, to 230,400,000 reads per day. Ingestion of this will go from MB/day to GB/sec. Reporting will transition to real-time analytics.
Dr. Pratt prefers to avoid trade-offs. Don't lose something to get something else. He also feels that language of the IT department can help. For example, he uses "Factor" like 25x rather than percent reduction (96 percent reduced). He feels this communicates the actual results more effectively.
Today's smarter consumers are driving the need for smarter technologies. Individual consumers and small businesses can make use of intelligent meters to help reduce their energy costs. Everything from smart cars to smart grids will need real-time analytics to deal with the millions of events that occur every day.
IBM's Data Protection and Retention Story
Brian Truskowski came back to provide the latest IBM messaging for Data Protection and Retention (DP&R). The key themes were:
Stop storing so much
Store more with what's on the floor
Move data to the right place
IBM announced today that the IBM Real-Time Compression Appliances now support EMC gear, such as EMC Celerra. While some of the EMC equipment have built-in compression features, these often come at a cost of performance degradation. Instead, the IBM Real-Time compression can offer improved performance as well as 3x to 5x reduction in storage capacity.
OVer 70 percent of data on disk has not be accessed in the last 90 days. IBM Easy Tier on the DS8700 and DS8800 now support FC-to-SATA automated tiering.
IBM is projecting that backup and archive storage will grow at over 50 percent per year. To help address this, IBM is launching a new "Storage Infrastructure Optimization" assessment. All attendees at today's summit are eligible for a free assessment.
Analytics are increasing the value of information, and making it more accessible to the average knowledge worker. The cost of losing data, as well as the effort spent searching for information, has skyrocketed. Users have grown to expect 100 percent uptime availability.
An analysis of IT environments found that only 55 percent was spent on revenue-producing workloads. The remaining 45 percent was spent on Data Protection and Retenion. That means that for every IT dollar spent on projects to generate revenue, you are spending another 90 cents to protect it. Imagine spending 90 percent of your house payments for homeowners' insurance, or 90 percent of your car's purchase price for car insurance.
IBM has organized its solutions into three categories:
Hyper-Efficient Backup and Recovery
Continuous Data Availability
What would it mean to your business if you could shift some of the money spent on DP&R over to revenue-producing projects instead? That was the teaser question posed at the end of these morning sessions for us to discuss during lunch.
Every January, we look back into the past as well as look into the future for trends to watch for the upcoming year. Ray Lucchesi of Silverton Consulting has a great post looking back at the [Top 10 storage technologies over the last decade]. I am glad to see that IBM has been involved with and instrumental in all ten technologies.
Looking into the future, Mark Cox of eChannel has an article [Storage Trends to Watch in 2011], based on his interviews with two fellow IBM executives: Steve Wojtowecz, VP of storage software development, and Clod Barrera, distinguished engineer and CTO for storage. Let's review the four key trends:
Cloud Storage and Cloud Computing
No question: Cloud Computing will be the battleground of the IT industry this decade. I am amused by the latest spate of Microsoft commercials where problems are solved with someone saying "...to the cloud". Riding on the coat tails of this is "Cloud Storage", the ability to store data across an Internet Protocol (IP) network, such as 10GbE Ethernet, in support of Cloud Computing applications. Cloud Storage protocols in the running include NFS, CIFS, iSCSI and FCoE.
Mark writes "..vendors who aren't investing in cloud storage solutions will fall behind the curve."
Economic Downturn forces Innovation
The old British adage applies: "Necessity is the mother of invention." The status quo won't do. In these difficult economic times, IT departments are running on constrained budgets and staff. This forces people to evaluate innovative technologies for storage efficiency like real-time compression and data deduplication to make better use of what they currently have. It also is forcing people to take a "good enough" attitude, instead of paying premium prices for best-of-breed they don't really need and can't really afford.
IT Service Management
Companies are getting away from managing individual pieces of IT kit, and are focusing instead on the delivery of information, from the magnetic surface of disk and tape media, to the eyes and ears of the end users. The deployment mix of private, hybrid and public clouds makes this even more important to measure and manage IT as a set of services that are delivered to the business. IT Service Management software can be the glue, helping companies implement ITIL v3 best practices and management disciplines.
Smarter Data Placement
A recent survey by "The Info Pro" analysts indicates that "managing storage growth" is considered more critical than "managing storage costs" or "managing storage complexity".
This tells me that companies are willing to spend a bit extra to deploy a tiered information infrastructure if it will help them manage storage growth, which typically ranges around 40 to 60 percent per year. While I have discussed the concept of "Information Lifecycle Management" (ILM), for the past four years on this blog, I am glad to see it has gone mainstream, helped in part with automated storage tiering features like IBM System Storage Easy Tier feature on the IBM DS8000, SAN Volume Controller and Storwize V7000 disk systems. Not all data is created equal, so the smart placement of data, based on the business value of the information contained, makes a lot of sense.
These trends are influencing what solutions the various different vendors will offer, and will influence what companies purchase and deploy.
Continuing my post-week coverage of the [Data Center 2010 conference], Thursday morning had some interesting sessions for those that did not leave town last night.
Interactive Session Results
In addition to the [Profile of Data Center 2010] that identifies the demographics of this year's registrants, the morning started with highlights of the interactive polls during the week.
External or Heterogeneous Storage Virtualization
The analyst presented his views on the overall External/Heterogeneous Storage Virtualization marketplace. He started with the key selling points.
Avoid vendor lock-in. Unlike the IBM SAN Volume Controller, many of the other storage virtualization products result in vendor lock-in.
Leverage existing back-end capacity. Limited to what back-end storage devices are supported.
Simplify and unify management of storage. Yes, mostly.
Lower storage costs. Unlike the IBM SAN Volume Controller, many using other storage virtualization discover an increase in total storage costs.
Migration tools. Yes, as advertised.
Consolidation/Transition. Yes, over time.
Better functionality. Potentially.
Shortly after several vendors started selling external/heterogeneous storage virtualization solutions, either as software or pre-installed appliances, major storage vendors that were caught with their pants down immediately started calling everything internally as also "storage virtualization" to buy some time and increase confusion.
While the analyst agreed that storage virtualization simplifies the view of storage from the host server side, it can complicate the management of storage on the storage end. This often comes up at the Tucson Briefing Center. I explain this as the difference between manual and automatic transmission cars. My father was a car mechanic, and since he is the sole driver and sole mechanic, he prefers manual transmission cars, easier to work on. However, rental car companies, such as Hertz or Avis, prefer automatic transmission cars. This might require more skills on behalf of their mechanics, but greatly simplifies the experience for those driving.
The analyst offered his views on specific use cases:
Data Migration. The analyst feels that external virtualization serves as one of the best tools for data migration. But what about tech refresh of the storage virtualization devices themselves? Unlike IBM SAN Volume Controller, which allows non-disruptive upgrades of the nodes themselves, some of the other solutions might make such upgrades difficult.
Consolidation/Transition. External virtualization can also be helpful, depending on how aggressive the schedule for consolidation/transition is performed.
Improved Functionality/Usability. IBM SAN Volume Controller is a good example, an unexpected benefit. Features like thin provisioning, automated storage tiering, and so on, can be added to existing storage equipment.
The analyst mentioned that there were different types of solutions. The first category were those that support both internal storage and external storage virtualization, like the HDS USP-V or IBM Storwize V7000. He indicated that roughly 40 percent of HDS USP-V are licensed for virtualization. The second category were those that support external virtualization only, such as IBM SAN Volume Controller, HP Lefthand and SVSP, and so on. The third category were software-only Virtual Guest images that could provide storage virtualization capabilities.
The analyst mentioned EMC's failed product Invista, which sold less than 500 units over the past five years. The low penetration for external virtualization, estimated between 2-5 percent, could be explained from the bad taste that left in everyone considering their options. However, the analyst predicts that by 2015, external virtualization will reach double digit marketshare.
Having a feel for the demographics of the registrants, and specific interactive polling in each meeting, provides a great view on who is interested in what topic, and some insight into their fears and motivations.
Continuing my coverage of the [Data Center 2010 conference], Tuesday afternoon I presented "Choosing the Right Storage for your Server Virtualization". In 2008 and 2009, I attended this conference as a blogger only, but this time I was also a presenter.
The conference asked vendors to condense their presentations down to 20 minutes. I am sure this was inspired by the popular 18-minute lectures from the [TED conference] or perhaps the [Pecha Kucha] night gatherings in Japan where each presenter speaks while showing 20 slides for 20 seconds each, This forces the presenters to focus on their key points and not fill the time slot with unnecessary marketing fluff. This also allows more vendors to have a chance to pitch their point of view.
Intelligent block-level disk array that virtualizes both internal and external disk storage
8 Gbps FCP and 1GbE iSCSI
IBM Storwize V7000 disk system
Real-time compression appliance for files
10GbE/1GbE CIFS and NFS
Storwize, now an IBM company
IBM Real-time Compression STN-6800 appliance
1GbE CIFS and NFS
IBM Real-time Compression STN-6500 appliance
If you think this is the first time a company like IBM has pulled shenanigans with product names like this, think again. Here are a few posts that might refresh your memory:
In my September 2006 post, [A brand by any other name...] I explain that I started blogging specifically to promote the new "IBM System Storage" product line name, part of the "IBM Systems" brand resulting from merging the "eServer" and "TotalStorage' brands.
In my January 2007 post, [When Names Change], I explain our naming convention for our disk products, including our DS family, SAN Volume Controller and N series.
In my February 2008 post, [Getting Off the Island], I cover how the x/p/i/z designations came about for our various IBM server product lines.
But what about acquisitions? When [IBM acquired Lotus Development Corporation], it kept the "Lotus" brand. New products that fit the "collaboration" function were put under the Lotus brand. I think most people can accept this approach.
But have we ever seen an existing product renamed to an acquired name?
In my post January 2009 post
[Congratulations to Ken on your QCC Milestone], I mentioned that my colleague Ken Hannigan worked on an internal project initially called "Workstation Data Save Facility" (WDSF) which was changed to "Data Facility Distributed Storage Manager" (DFDSM), then renamed to "ADSTAR Distributed Storage Manager" (ADSM), and finally renamed to the name it has today: IBM Tivoli Storage Manager (TSM).
Readers reminded me that [IBM acquired Tivoli Systems, Inc.] in 1996, so TSM could not have been an internally developed product. Ha! Wrong! Let's take a quick history lesson on how this came about:
In the late 1980s, IBM Almaden research had developed a project to backup personal computers and workstations, which they called "Workstation Data Save Facility" or WDSF.
This was turned over to our development team, which immediately discarded the code, and wrote from scratch its replacmeent, called Data Facility Distributed Storage Manager (DFDSM), named similar to the Data Facility products on the mainframe (DFP, DFHSM, DFDSS). As a member of the Data Facility family, DFDSM didn't really fit. The rest processed mainframe data sets, but DFDSM processed Windows and UNIX files. That a version of DFDSM server was available to run on the mainframe was the only connection.
Then, in the early 1990s, there were discussions of possibly splitting IBM into a bunch of smaller "Baby Blues", similar to how [AT&T was split into "Baby Bells"], and how Forbes and Goldman Sachs now want to split Microsoft into [Baby Bills]. IBM considered naming the storage spin-off as ADSTAR, which stood for "Advanced Storage and Retrieval."
Pre-emptively, IBM renamed DFDSM to "ADSTAR Distributed Storage Manager" or ADSM.
Fortunately, in 1993, IBM brought a new sheriff to town, Lou Gerstner, who quickly squashed any plans to split up IBM. He quickly realized that IBM's core strength was building integrated stacks, combining systems, software and services to solve business problems.
In 1996, IBM acquired Tivoli Systems, Inc. to expand its "Systems Management" portfolio, and renamed ADSM over to IBM Tivoli Storage Manager, since "storage management" is an essential part of "systems management". Later, IBM TotalStorage Productivity Center would be renamed to "IBM Tivoli Storage Productivity Center."
I participated in five months of painful meetings to figure out what to name our new internally-developed midrange disk system. Since it ran SAN Volume Controller software, I pushed for keeping the SVC designation somehow. We considered DS naming convention, but the new midrange product would not fit between our existing DS5000 and DS6000 numbering scheme. A marketing agency we hired came up with nonsensical names, in the spirit of product names like Celerra, Centera and CLARiiON, using name generators like [Wordoid]. Luckily, in the nick of time, IBM acquired Storwize for its compression technology, and decided that Storwize as a name was way better fit than any of the names we came up with already.
However, the new IBM Storwize V7000 midrange product had nothing in common with the appliances acquired from Storwize, the company, so to avoid confusion, the latter products were renamed to [IBM Real-time Compression]. Fellow blogger Steven Kenniston, the Storage Alchemist from Storwize fame now part of IBM from the acquisition, gives his perspective on this in his post [Storwize – What is in a Name, Really?]. While I am often critical of the names and terms IBM uses, I have to say this last set of naming decisions makes a lot of sense to me and I support it wholeheartedly.
In his last post in this series, he mentions that the amazingly successful IBM SAN Volume Controller was part of a set of projects:
"IBM was looking for "new horizon" projects to fund at the time, and three such projects were proposed and created the "Storage Software Group". Those three projects became know externally as TPC, (TotalStorage Productivity Center), SanFS (SAN File System - oh how this was just 5 years too early) and SVC (SAN Volume Controller). The fact that two out of the three of them still exist today is actually pretty good. All of these products came out of research, and its a sad state of affairs when research teams are measured against the percentage of the projects they work on, versus those that turn into revenue generating streams."
But this raises the question: Was SAN File System just five years too early?
IBM classifies products into three "horizons"; Horizon-1 for well-established mature products, Horizon-2 was for recently launched products, and Horizon-3 was for emerging business opportunities (EBO). Since I had some involvement with these other projects, I thought I would help fill out some of this history from my perspective.
Back in 2000, IBM executive [Linda Sanford] was in charge of IBM storage business and presented that IBM Research was working on the concept of "Storage Tank" which would hold Petabytes of data accessible to mainframes and distributed servers.
In 2001, I was the lead architect of DFSMS for the IBM z/OS operating system for mainframes, and was asked to be lead architect for the new "Horizon 3" project to be called IBM TotalStorage Productivity Center (TPC), which has since been renamed to IBM Tivoli Storage Productivity Center.
In 2002, I was asked to lead a team to port the "SANfs client" for SAN File System from Linux-x86 over to Linux on System z. How easy or difficult to port any code depends on how well it was written with the intent to be ported, and porting the "proof-of-concept" level code proved a bit too challenging for my team of relative new-hires. Once code written by research scientists is sufficiently complete to demonstrate proof of concept, it should be entirely discarded and written from scratch by professional software engineers that follow proper development and documentation procedures. We reminded management of this, and they decided not to make the necessary investment to add Linux on System z as a supported operating system for SAN file system.
In 2003, IBM launched Productivity Center, SAN File System and SAN Volume Controller. These would be lumped together with Horizon-1 product IBM Tivoli Storage Manager and the four products were promoted together as the inappropriately-named [TotalStorage Open Software Family]. We actually had long meetings debating whether SAN Volume Controller was hardware or software. While it is true that most of the features and functions of SAN Volume Controller is driven by its software, it was never packaged as a software-only offering.
The SAN File System was the productized version of the "Storage Tank" research project. While the SAN Volume Controller used industry standard Fibre Channel Protocol (FCP) to allow support of a variety of operating system clients, the SAN File System required an installed "client" that was only available initially on AIX and Linux-x86. In keeping with the "open" concept, an "open source reference client" was made available so that the folks at Hewlett-Packard, Sun Microsystems and Microsoft could port this over to their respective HP-UX, Solaris and Windows operating systems. Not surprisingly, none were willing to voluntarily add yet another file system to their testing efforts.
Barry argues that SANfs was five years ahead of its time. SAN File System tried to bring policy-based management for information, which has been part of DFSMS for z/OS since the 1980s, over to distributed operating systems. The problem is that mainframe people who understand and appreciate the benefits of policy-based management already had it, and non-mainframe couldn't understand the benefits of something they have managed to survive without.
(Every time I see VMware presented as a new or clever idea, I have to remind people that this x86-based hypervisor basically implements the mainframe concept of server virtualization introduced by IBM in the 1970s. IBM is the leading reseller of VMware, and supports other server virtualization solutions including Linux KVM, Xen, Hyper-V and PowerVM.)
To address the various concerns about SAN File System, the proof-of-concept code from IBM Research was withdrawn from marketing, and new fresh code implementing these concepts were integrated into IBM's existing General Parallel File System (GPFS). This software would then be packaged with a server hardware cluster, exporting global file spaces with broad operating system reach. Initially offered as IBM Scale-out File Services (SoFS) service offering, this was later re-packaged as an appliance, the IBM Scale-Out Network Attached Storage (SONAS) product, and as IBM Smart Business Storage Cloud (SBSC) cloud storage offering. These now offer clustered NAS storage using the industry standard NFS and CIFS clients that nearly all operating systems already have.
Today, these former Horizon-1 products are now Horizon-2 and Horizon-3. They have evolved. Tivoli Storage Productivity Center, GPFS and SAN Volume Controller are all market leaders in their respective areas.
Last week, in Computer Technology Review's article [Tiering: Scale Up? Scale Out? Do Both], Mark Ferelli interviews fellow blogger Hu Yoshida, CTO of Hitachi Data Systems (HDS). Here's an excerpt:
"MF/CTR: A global cache should be required to implement that common pool that you’re talking about going across all tiers.
Hu/HDS: Right. So that is needed to get to all the resources. Now with our system, we can also attach external storage behind it for capacity so that as the storage ages out or becomes less active we can move it to the external storage. They would certainly have less performance capability, but you don’t need it for the stale data that we’re aging down. Right now we’re the only vendor that can provide this type of tiering.
If you look at other people who do virtualization like IBM’s SVC, the SVC has no storage within it because it’s sitting so if you attach any storage behind it, there is some performance degradation because you have this appliance sitting in front. That appliance is also very limited in cache and very limited in the number of storage boards on it. It cannot really provide you additional performance than what is attached behind it. And in fact, it will always degrade what is attached behind it because it’s not storage, where as our USP is storage and it has a global cache and it has thousands of port connections, load balancing and all that. So our front end can enhance existing storage that sits behind it."
This is not the first time I have had to correct Hu and others of misperceptions of IBM's SAN Volume Controller (SVC). This month marks my four year "blogoversary", and I seem to spend a large portion of my blogging time setting the record straight. Here are just a few of my favorite posts setting the record straight on SVC back in 2007:
Since day 1, SAN Volume Controllers has focused primarily on external storage. Initially, the early models had just battery-protected DRAM cache memory, but the most recent model of the SVC, the 2145-CF8, adds support for internal SLC NAND flash solid state drives. To fully appreciate how SVC can help improve the performance of the disks that are managed, I need to use some visual aids.
In this first chart, we look at a 70/30/50 workload. This indicates that 70 percent of the IOPS are reads, 30 percent writes, and 50 percent can be satisfied as cache hits directly from the SVC. For the reads, this means that 50 percent are read-hits satisfied from SVC DRAM cache, and 50 percent are read-miss that have to get the data from the managed disk, either from the managed disk's own cache, or from the actual spinning drives inside that managed disk array.
For writes, all writes are cache-hits, but some of them will be destaged to the managed disk. Typically, we find that a third of writes are over-written before this happens, so only two-thirds are written down to managed disk.
In this example, the SVC reduced the burden of the managed disk from 100,000 IOPS down to 55,000, which is 35,000 reads and 20,000 writes. Some have argued against putting one level of cache (SVC) in front of another level of cache (managed disk arrays). However, CPU processor designers have long recognized the value of hierarchical cache with L1, L2, L3 and sometimes even L4 caches. The cache-hits on SVC are faster than most disk system's cache-hits.
This is a Ponder curve, mapping millisecond response (MSR) times for different levels of I/O per second, named after the IBM scientist John Ponder that created them. Most disk array vendors will publish similar curves for each of their products. In this case, we see that 100,000 IOPS would cause a 25 millisecond response (MSR) time, but when the load is reduced to 55,000 IOPS, the average response time drops to only 7 msec.
To be fair, the SVC does introduce 0.06 msec of additional latency on read-misses, so let's call this 7.06 msec. This tiny amount of latency could be what Hu Yoshida was referring to when he said there was "some performance degradation". There are other storage virtualization products in the market that do not provide caching to boost performance, but rather just map incoming requests to outgoing requests, and these can indeed slow down every I/O they process. Perhaps Hu was thinking of those instead of IBM's SVC when he made his comments.
Of course, not all workloads are 70/30/50, and not every disk array is driven to its maximum capability, so your mileage may vary. As we slide down the left of the curve where things are flatter, the improvement in performance lowers.
IOPS before SVC
IOPS after SVC
MSR before SVC
MSR after SVC
Hitachi's offerings, including the HDS USP-V, USP-VM and their recently announced Virtual Storage Platform (VSP) sold also by HP under the name P9500, have similar architecture to the SVC and can offer similar benefits, but oddly the Hitachi engineers have decided to treat externally attached storage as second-class citizens instead. Hu mentions data that "ages out or becomes less active we can move it to the external storage." IBM has chosen not to impose this "caste" system onto its design of the SAN Volume Controller.
The SVC has been around since 2003, before the USP-V came to market, and has sold over 20,000 SVC nodes over the past seven years. The SVC can indeed improve performance of managed disk systems, in some cases by a substantial amount. The 0.06 msec latency on read-miss requests represents less than 1 percent of total performance in production workloads. SVC nearly always improves performance, and in the worst case, provides same performance but with added functionality and flexibility. For the most part, the performance boost comes as a delightful surprise to most people who start using the SVC.
To learn more about IBM's upcoming products and how IBM will lead in storage this decade, register for next week's webcast "Taming the Information Explosion with IBM Storage" featuring Dan Galvan, IBM Vice President, and Steve Duplessie, Senior Analyst and Founder of Enterprise Storage Group (ESG).
Continuing my coverage of the annual [2010 System Storage Technical University], I participated in the storage free-for-all, which is a long-time tradition, started at SHARE User Group conference, and carried forward to other IT conferences. The free-for-all is a Q&A Panel of experts to allow anyone to ask any question. These are sometimes called "Birds of a Feather" (BOF). Last year, they were called "Meet the Experts", one for mainframe storage, and the other for storage attached to distributed systems. This year, we had two: one focused on Tivoli Storage software, and the second to cover storage hardware. This post provides a recap of the Storage Hardware free-for-all.
The emcee for the event was Scott Drummond. The other experts on the panel included Dan Thompson, Carlos Pratt, Jack Arnold, Jim Blue, Scott Schroder, Ed Baker, Mike Wood, Steve Branch, Randy Arseneau, Tony Abete, Jim Fisher, Scott Wein, Rob Wilson, Jason Auvenshine, Dave Canan, Al Watson, and myself, yours truly, Tony Pearson.
What can I do to improve performance on my DS8100 disk system? It is running a mix of sequential batch processing and my medical application (EPIC). I have 16GB of cache and everything is formatted as RAID-5.
We are familiar with EPIC. It does not "play well with others", so IBM recommends you consider dedicating resources for just the EPIC data. Also consider RAID-10 instead for the EPIC data.
How do I evaluate IBM storage solutions in regards to [PCI-DSS] requirements.
Well, we are not lawyers, and some aspects of the PCI-DSS requirements are outside the storage realm. In March 2010, IBM was named ["Best Security Company"] by SC Magazine, and we have secure storage solutions for both disk and tape systems. IBM DS8000 and DS5000 series offer Full Disk Encryption (FDE) disk drives. IBM LTO-4/LTO-5 and TS1120/TS1130 tape drives meet FIPS requirements for encryption. We will provide you contact information on an encryption expert to address the other parts of your PCI-DSS specific concerns.
My telco will only offer FCIP routing for long-distance disk replication, but my CIO wants to use Fibre Channel routing over CWDM, what do I do?
IBM XIV, DS8000 and DS5000 all support FC-based long distance replication across CWDM. However, if you don't have dark fiber, and your telco won't provide this option, you may need to re-negotiate your options.
My DS4800 sometimes reboots repeatedly, what should I do.
This was a known problem with microcode level 760.28, it was detecting a failed drive. You need to replace the drive, and upgrade to the latest microcode.
Should I use VMware snapshots or DS5000 FlashCopy?
VMware snapshots are not free, you need to upgrade to the appropriate level of VMware to get this function, and it would be limited to your VMware data only. The advantage of DS5000 FlashCopy is that it applies to all of your operating systems and hypervisors in use, and eliminates the consumption of VMware overhead. It provides crash-consistent copies of your data. If your DS5000 disk system is dedicated to VMware, then you may want to compare costs versus trade-offs.
Any truth to the rumor that Fibre Channel protocol will be replaced by SAS?
SAS has some definite cost advantages, but is limited to 8 meters in length. Therefore, you will see more and more usage of SAS within storage devices, but outside the box, there will continue to be Fibre Channel, including FCP, FICON and FCoE. The Fibre Channel Industry Alliance [FCIA] has a healthy roadmap for 16 Gbps support and 20 Gbps interswitch link (ISL) connections.
What about Fibre Channel drives, are these going away?
We need to differentiate the connector from the drive itself. Manufacturers are able to produce 10K and 15K RPM drives with SAS instead of FC connectors. While many have suggested that a "Flash-and-Stash" approach of SSD+SATA would eliminate the need for high-speed drives, IBM predicts that there just won't be enough SSD produced to meet the performance needs of our clients over the next five years, so 15K RPM drives, more likely with SAS instead of FC connectors, will continue to be deployed for the next five years.
We'd like more advanced hands-on labs, and to have the certification exams be more product-specific rather than exams for midrange disk or enterprise disk that are too wide-ranging.
Ok, we will take that feedback to the conference organizers.
IBM Tivoli Storage Manager is focused on disaster recovery from tape, how do I incorporate remote disk replication.
This is IBM's Unified Recovery Management, based on the seven tiers of disaster recovery established in 1983 at GUIDE conference. You can combine local recovery with FastBack, data center server recovery with TSM and FlashCopy manager, and combine that with IBM Tivoli Storage Productivity Center for Replication (TPC-R), GDOC and GDPS to manage disk replication across business continuity/disaster recovery (BC/DR) locations.
IBM Tivoli Storage Productivity Center for Replication only manages the LUNs, what about server failover and mapping the new servers to the replicated LUNs?
There are seven tiers of disaster recovery. The sixth tier is to manage the storage replication only, as TPC-R does. The seventh tier adds full server and network failover. For that you need something like IBM GDPS or GDOC that adds this capability.
All of my other vendor kit has bold advertising, prominent lettering, neon lights, bright colors, but our IBM kit is just black, often not even identifying the specific make or model, just "IBM" or "IBM System Storage".
IBM has opted for simplified packaging and our sleek, signature "raven black" color, and pass these savings on to you.
Bring back the SHARK fins!
We will bring that feedback to our development team. ("Shark" was the codename for IBM's ESS 800 disk model. Fiberglass "fins" were made as promotional items and placed on top of ESS 800 disk systems to help "identify them" on the data center floor. Unfortunately, professional golfer [<a href="http://www.shark.com/">Greg Norman</a>] complained, so IBM discontinued the use of the codename back in 2005.)
Where is Infiniband?
Like SAS, Infiniband had limited distance, about 10 to 15 meters, which proved unusable for server-to-storage network connections across data center floorspace. However, there are now 150 meter optical cables available, and you will find Infiniband used in server-to-server communications and inside storage systems. IBM SONAS uses Infiniband today internally. IBM DCS9900 offers Infiniband host-attachment for HPC customers.
We need midrange storage for our mainframe please?
In addition to the IBM System Storage DS8000 series, the IBM SAN Volume Controller and IBM XIV are able to connect to Linux on System z mainframes.
We need "Do's and Don'ts" on which software to run with which hardware.
IBM [Redbooks] are a good source for that, and we prioritize our efforts based on all those cards and letters you send the IBM Redbooks team.
The new TPC v4 reporting tool requires a bit of a learning curve.
The new reporting tool, based on Eclipse's Business Intelligence Reporting Tool [BIRT], is now standardized across the most of the Tivoli portfolio. Check out the [Tivoli Common Reporting] community page for assistance.
An unfortunate side-effect of using server virtualization like VMware is that it worsens management and backup issues. We now have many guests on each blade server.
IBM is the leading reseller of VMware, and understands that VMware adds an added layer of complexity. Thankfully, IBM Tivoli Storage Manager backups uses a lightweight agent. IBM [System Director VMcontrol] can help you manage a variety of hypervisor environments.
This was a great interactive session. I am glad everyone stayed late Thursday evening to participate in this discussion.
"With Cisco Systems, EMC, and VMware teaming up to sell integrated IT stacks, Oracle buying Sun Microsystems to create its own integrated stacks, and IBM having sold integrated legacy system stacks and rolling in profits from them for decades, it was only a matter of time before other big IT players paired off."
Once again we are reminded that IBM, as an IT "supermarket", is able to deliver integrated software/server/storage solutions, and our competitors are scrambling to form their own alliances to be "more like IBM." This week, IBM announced new ordering options for storage software with System x servers, including BladeCenter blade servers and IntelliStation workstations. Here's a quick recap:
IBM Tivoli Storage Manager FastBack v6.1 supports both Windows and Linux! FastBack is a data protection solution for ROBO (Remote Office, Branch Office) locations. It can protect Microsoft Exchange, Lotus Domino, DB2, Oracle applications. FastBack can provide full volume-level recovery, as well as individual file recovery, and in some cases Bare Machine Recovery. FastBack v6.1 can be run stand-alone, or integrated with a full IBM Tivoli Storage Manager (TSM) unified recovery management solution.
FlashCopy Manager v2.1
FlashCopy Manager uses point-in-time copy capabilities, such as SnapShot or FlashCopy, to protect application data using an application-aware approach for Microsoft Exchange, Microsoft SQL server, DB2, Oracle, and SAP. It can be used with IBM SAN Volume Controller (SVC), DS8000 series, DS5000 series, DS4000 series, DS3000 series, and XIV storage systems. When applicable, FlashCopy manager coordinates its work with Microsoft's Volume Shadow Copy Services (VSS) interface. FlashCopy Manager can provide data protection using just point-in-time disk-resident copies, or can be integrated with a full IBM Tivoli Storage Manager (TSM) unified recovery management solution to move backup images to external storage pools, such as low-cost, energy-efficient tape cartridges.
General Parallel File System (GPFS) v3.3 Multiplatform
GPFS can support AIX, Linux, and Windows! Version 3.3 adds support for Windows 2008 Server on 64-bit chipset architectures from AMD and Intel. Now you can have a common GPFS cluster with AIX, Linux and Windows servers all sharing and accessing the same files. A GPFS cluster can have up to 256 file systems. Each of these file systems can be up to 1 billion files, up to 1PB of data, and can have up to 256 snapshots. GPFS can be used stand-alone, or integrated with a full IBM Tivoli Storage Manager (TSM) unified recovery management solution with parallel backup streams.
For full details on these new ordering options, see the IBM [Press Release].
Continuing my coverage of the Data Center Conference, Dec 1-4, 2009 here in Las Vegas, this post focused on data protection strategies.
Two analysts co-presented this session which provided an overview of various data protection techniques. A quick survey of the audience found that 27 percent have only a single data center, 13 percent have load sharing of their mission critical applications across multiple data centers, and the rest use a failover approach to either development/test resources, standby resources or an outsourced facility.
There are basically five ways to replicate data to secondary locations:
Array-based replication. Many high-end disk arrays offer this feature. IBM's DS8000 and XIV both have synchronous and asynchronous mirroring. Data Deduplication can help in this regard to reduce the amount of data transmitted across locations.
NAS-based replication. I consider this just another variant of the first, but this can be file-based instead of block-based, and can often be done over the public internet rather than dark fiber.
Network-based replication. This is the manner that IBM SAN Volume Controller, EMC RecoverPoint, and others can replicate. The analysts liked this approach as it was storage vendor-independent.
Host-based replication. This is often done by the host's Operating System, such as through a Logical Volume Manager (LVM) component.
Application/Database replication. There are a variety of techniques, including log shipping of transactions, SQL replication, and active/active application-specific implementations.
The analysts felt that "DR Testing" has become a lost art. People are just not doing it as often as they should, or not doing it properly, resulting in surprises when a real disaster strikes.
A question came up about the confusion between "Disaster Recovery Tiers" and Uptime Institute's "Data Center Facilities Tiers". I agree this is confusing. Many clients call their most mission critical applications as Tier 1, less critical as Tier 2, and least critical as Tier 3. In 1983, IBM User Group GUIDE came up with "Business Continuity Tiers" where Tier 1 was the slowest recovery from manual tape, and Tier 7 was the fastest recovery with a completely automated site, network, server and storage failover. However, for Data Center facility tiers, Uptime has the simplest least available (99.3 percent uptime) data center as Tier 1, and the most advanced, redundant, highest available (99.995 percent) data center as Tier 4. This just goes to show that when one person starts using "Tier 1" or "Tier 4" terminology, it can be misinterpreted by others.
This week several IBM executives will present at the 28th Annual Data Center Conference here in Las Vegas. Here is a quick recap:
Steve Sams: Data Center Cost Saving Actions Your CFO Will Love
A startling 78 percent of today's data centers were built in the last century, before the "dot com" era and the adoption of high-density blade servers. IBM Vice President of Global Site and Facility Services, Steve Sams, presented actions that can help extend the life of existing data centers, help rationalize the infrastructure across the company, and design a new data center that is flexible and responsive to changing needs.
In one example, an 85,000 square foot datacenter in Lexington had reached 98 percent capacity based on power/cooling requirements. They estimated it would take $53 million US dollars to either upgrade the facility or build a new facility to meet projected growth. Instead, IBM was able to consolidate servers six-to-one, an 85 percent reduction. IBM also was able to make changes to the cooling equipment, redirect airflow and changed out the tiles, re-oriented the servers for more optimal placement, and implement measurement and management tools. The end result? The facility now has eight times the compute capability and enjoys 15 percent headroom for additonal growth. All this for only 1.5 million US dollar investment, instead of 53 million.
IBM builds hundreds of data centers for clients large and small. In addition to the "Portable Modular Data Center"(PMDC) shipping container on display at the Solution Showcase, IBM offers the "Scalable Modular Data Center", a turn-key system with a small 500 to 2500 square foot size for small customers. For larger deployments, the "Enterprise Modular Data Center" offers standardized deployments in 5000 square foot increments. IBM also offers "High Density Zones" which can be perfect way to avoid a full site retrofit.
Helene Armitage: IT-wide Virtualization
Helene is IBM General Manager of the newly formed IBM System Software division. A smarter planet will require more dynamic infrastructures, which is IBM's approach to helping clients through the virtualization journey. The virtualization of resources, workloads and business processes will require end-to-end management. To help, IBM offers IBM Systems Director.
Helene indicated that there are four stages of adoption:
Physical consolidation - VMware and Hyper-V are the latest examples of running many applications on fewer physical servers. Of course, IBM has been doing this for decades with mainframes, and has had virtualization on System i and System p POWER systems as well. A quick survey of the audience found that about 20 percent were doing server virtualization on non-x86 platforms (for example, PowerVM or System z mainframe z/VM)
Pools of resources - SAN Volume Controller is an example solution to manage storage as a pool of disparate storage resources. Supercomputers manage pools of servers.
Integrated Service Management - in the past, resources were managed by domain, resulting in islands of management. Now, with IBM Systems Director, you can manage AIX, IBM i, Linux and Windows servers, including non-IBM servers running Linux and Windows.
Service management can provide monitoring, provisioning, service catalog, self-service, and business-aligned processes.
Cloud computing - Helene agreed that not everyone will get to this stage. Some will adopt cloud computing, whether public, private or some kind of hybrid, and others may be fine at stage 3.
For those clients that want assistance, IBM offers three levels of help:
Help me decide what is best for me
Help me implement what I have decided to do
Help me manage and run my operations
With IBM's compelling vision for the future, best of breed solutions, leadership in management software, extensive experience in services, and solid business industry knowledge, it makes sense to tap IBM to help with your next IT transformation.
Well, it's Wednesday! Normally, IBM makes its announcements on Tuesday's, but this week that landed on the 13th, and some people are superstitious, so we pushed it back to today. Fellow IBM master inventory Barry Whyte starts the first in a series of posts with: New SVC v5 CF8 node with native SSD support.
There are really two separate items being announced for the IBM System Storage SAN Volume Controller (SVC):
SVC v5 software
The software moves from a 32-bit kernel to a 64-bit kernel. Fortunately, IBM had the foresight to know that would happen back in 2005, so models 8F2, 8F4 and 8G4 can be upgrade to this new software level and gain new functionality. This is because these models have 64-bit capable processors. Those with six-year-old 4F2 will continue to run on SVC 4.3.1, but should consider it's about time to upgrade soon.
New 2145-CF8 model
The CF8 is based on the IBM System x 3550M2. Each node can have up to 4 Solid-State Drives (SSD) that can be treated as SVC Managed Disk Groups. Virtual disks can be easily migrated from hard disk drives (HDD) over to SSD, processed, and then move them back to HDD. By treating the SSD as managed disks, rather than an extension of the cache, we are able to support all of the features and functions in a seamless manner.
As Barry says, IBM has been working on this for quite a while, and based on initial responses looks to be quite successful in the market!