Tony Pearson is a Master Inventor and Senior IT Architect for the IBM Storage product line at the
IBM Executive Briefing Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services.
(Short URL for this blog: ibm.co/Pearson )
My books are available on Lulu.com! Order your copies today!
Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Well, we had another successful event in Second Life today.
Unlike our April 26 launch of our System Storage products for IBM Business Partners only, this time we decided this time to make it as a "Meet the Storage Experts" Q&A Panel format, and open up registration to everyone. Thesubject matter experts sat at the front of the room on four stools. We had six rows of chairs arrangedsemi-circularly.
Shown above, from left to right, are the avatars of our four experts:
IBM System Storage N series, focusing on recent N3000 disk system announcements
Harold Pike (holding the microphone while speaking)
IBM System Storage DS3000 and DS4000 series, focusing on recent DS3000 disk system announcements
IBM System Storage TS series, focusing on recent TS2230, TS3400 and TS7700 tape system announcements
IBM storage networking, focusing on recent IBM SAN256B director blade announcements
While Eric was a veteran Second Lifer, having presented at our April event, the other three were trainedon how to raise their hand, speak into the microphone, sit on the stool, and so on. I want to thank allof our experts for putting in this effort!
The event was produced by Katrina H Smith. She did a great job, and made sure we were on top ofall the issues and tasks required to get the job done. Running a Second Life event is every bit ashard as running a real face-to-face event. We had several meetings to discuss venue details, placementof chairs, placement of product demos, audio/video recording, wall decorations, tee-shirt and coffee mug design, logistics, and so on.
I acted as moderator/emcee for the event. That is my back in the picture above. The process wassimple, modeled after the "Birds of a Feather" sessions at events like SHARE and the IBMStorage and Storage Networking Symposium. We threw out a list of topics the experts would cover,and people in the audience would "raise their left hand". I, as the moderator, would then walkover to each person, and hold out the microphone for them to ask the question. I would then repeat the question and ask the appropriate expert to provide an answer. We defined gestures onhow to "raise hand" and "put hand down" that we gave to each registered participant.
We had four dedicated "camera-avatars" in world to capture both video and screenshots.Our video editors are now working to edit "highlight videos" that we can use at future events, for training materials, and for our internal "BlueTube" online video system.
The room was filled with examples of each of our products, made into 3D objects that were dimensionallycorrect, and "textured" with photographs of the actual products. If you click on an object, you get a "notecard" that provided more information. Special thanks to Scott Bissmeyer for making all of theseobjects for us.
We made posters of each expert and placed them in all four corners of the room. On the bottom of each coffee mug was a picture of each of the experts, and if you walked under each of the posters, you were"dispensed" a coffee mug matching the expert shown in the poster.Participants could "Collect all Four!" When you bring the coffee mug up to takea sip, the picture on the bottom of the mug is exposed for all to see.And as a final give-away to the audience, we made a variety of event tee-shirts and polo-shirts.
At the end of the session, we asked everyone to click on the "Survey" kiosk near the exit door. We askedsix simple questions using SurveyMonkey.com that took only a fewminutes to process. We found asking questions immediately at the end of the event was the best way tocapture this feedback.
From a "Green" perspective, we had people registered from the following countries: US, India, Mexico,Australia, United Kingdom, Brazil, Germany, Argentina, Chile, China, Canada, and Venezuela. Second Lifeallows all these people who probably could not travel, or could not afford the time and expense to travel,to participate in a simulated face-to-face meeting without energy consumption of traditional travel methods.
More importantly, we got several leads for business. People often ask "Yes, but is there any businessassociated with this?" This time, there was, based on the answers to the questions, several avatars asked for a real sales call to follow-up on the products and offerings they were discussed.
With such a great success, we have already scheduled our next Second Life event, November 8. Mark your calendars! I'll postmore details on the registration process of the November event when available.
The keynote was led by Phil Tasker, IBM Business Unit Executive (BUE) for STG Education Programs in Growth Markets, then Joe Screnci, head of IBM Storage Sales for Australia. IBM is in the Top 10 Training Hall of Fame, and conducts over 40,000 classes worldwide, resulting in over 1.3 million student days of instructions. IBM Systems Lab and Training technical hosts over three dozen conferences like this one every year.
Next was Clod Barrera, Distinguished Engineer and Chief Technical Strategist for the IBM System Storage product line. He covered future trends in storage as they relate to IBM's Smarter COmputing initiative.
Storage for the Clouds
Clod Barrera presented this break-out session on Cloud Storage. He covered why clouds matter, the various types and purposes of cloud, technology and architectures, and where IBM is headed to support this trend.
Storage for Cloud computing was $1 Billion USD business in 2010, and is expected to grow 32 percent CAGR through, compared to 3.8 percent for non-cloud storage. Clod estimates that 10 to 15 percent of all storage will be in cloud deployments by 2015. Of this storage, analysts expect 50 percent in private clouds, and the other 50 percent in public clouds. For private clouds, clients are looking to "Cloudify" their existing IT infrastructures. For public clouds, the projects are mostly green field.
IBM is also looking to the "arms dealer" of choice for Telcos and other companies looking to launch their own Cloud Services. IBM has a Cloud Services Provider Platform (CSP2) specifically to provide all the tools and technologies needed to make this possible.
Last month, IBM launched several new solutions for Cloud. The IBM Starter Kit for Cloud will help existing IT environments adopt cloud technologies. The IBM Service Agility Accelerator for Cloud is available for more advanced deployments. IBM Service Delivery Manager (ISDM) integrates a collection of software to provide complete integrated service management. IBM CloudBurst provides an integrated hardware-and-software stack for both x86 and POWER chipsets.
Multi-tenancy is also a big issue, and this varies depending on deployment model: IaaS, PaaS, or SaaS. Multi-tenancy is needed to help divide up management tasks, and to ensure that shared resources are paid for and meet SLA requirements accordingly.
Clod feels there are good reasons to use high performance, transactional SAN storage for VMware environments, versus NAS which many people consider simpler to deploy. IBM is also active in open standards, including SNIA's Cloud Data Management Interface [CDMI].
Journey to the Private Cloud
Gary Luke from Brocade provided this session on IBM's SAN384B-2 and SAN768B-2 SAN directors. Brocade is one of IBM's suppliers for SAN switches, and thanks to TRILL being adopted last August by IETF, supports multi-hop FCoE configurations! However, Gary did not talk about FCoE, but rather native FCP and FICON support in these new directors.
According to VMware, only 30 percent of x86 workloads are virtualized by any hypervisor. Gary feels that server virtualization and the use of Solid-State Drives (SSD) in disk arrays are driving existing 8 Gbps SAN to upgrade to 16 Gbps. Gary feels that Fibre-Channel based SANs are best positioned to handle unpredictable peaks in a 24-by-7 world.
The SAN384B-2 can house up to 256 ports (8 Gbps) or 192 ports (16 Gbps) in four slots, 9U chassis. The SAN768B-2 can handle twice these, in a 12U chassis. The nice thing about the 16Gbps ports is that they can auto-negotiate down to 10, 8, 4 and 2 Gbps. This is far better than typical N-2 support, often referred to as the speeds supported, such as 4/2/1 and 8/4/2. An upcoming FOS release will allow people with previous generation SAN384B-1/SAN768B-1 directors to move their 8Gbps blades over to the new SAN384B-2/SAN768B-2 generation models.
Since most CWDM and DWDM only support maximum 10 Gbps FC and 10GbE, Brocade's 16Gbps can automatically drop down to 10 Gbps for direct attachment to CWDM/DWDM, rather than having a step-down box normally required.
A major advancement is the change from copper to optical "Inter-Chassis Links" (ICL). Unlike Inter-switch links (ISL) that use up SAN ports on each box, the ICL is faster, more efficient and does not consume ports. Normally, clients would connect two directors together, but now you can connect up to six chassis together! For example, you can have four SAN368B-2 connected to your host servers, ICL attached to two SAN768B-2, that are then connected to your disk and tape storage devices. The fiber optic ICL allow for up to 50 meters distance. Combining six chassis together would allow the complex to support over 3,000 ports (8 Gbps) or 2,300 ports (16 Gbps).
The SAN384B-2 and SAN768B-2 supports "virtual SAN" logical switches, traffic isoliation (TI) zones, fabric-assigned WWNNs, and fabric-based QoS.
Lastly, Brocade offers a free utility called [SANhealth] that will gather data from your b-type, m-type and even Cisco MDS-based SAN. The data can then be sent to Brocade for analysis, and Brocade will then email back some nice Visio graphs, spreadsheets and other analysis results on the health of your SAN.
Special thanks to Anthony Vandewerdt, who sent me his version of this presentation that he planned to present in Australia next week. I "smartened it up" (or whatever the appropriate phrase is the opposite of "dumbed it down") for the technical audience.
Recovery procedures for single and double drive failures. A double drive failure on an XIV typically involves less recovery effort than traditional RAID5-based disk systems, and in many cases results in no data loss whatsoever. I provided details on this in my blog post [Double Drive Failure Debunked: XIV Two Years Later], so no need to repeat myself here.
Replacing the Automatic Transfer Switch (ATS) non-disruptively. To support either single-phase and triple-phase power sources, the XIV uses an ATS to take two independent power feeds, and distribute this out to the three Uninterruptible Power Supplies (UPS).
Built-in Migration capability to copy data off other disk systems over to the XIV.
Configuring Synchronous and Asynchronous mirroring using either the Fibre Channel or Internet Protocol ports.
Optimizing the use of XIV for VMware, AIX and other operating systems.
The IBM XIV Storage System is quite popular in New Zealand, with four times more boxes sold per capita than the other countries in the Asia Pacific region. I covered both the A14 model as well as the new Gen3 model.
Business Continuity/Disaster Recovery (BC/DR) Update: Lessons, Planning, Solutions
My colleague Vic Peltz from IBM Almaden presented on lessons learned from Hurricane Katrina and various other natural disasters. Unlike tradtional presentations the focus on technology, Vic took a different approach, focusing on people and procedures. I was here last year when the earthquake hit Christchurch on the south island, so I was well aware that BC/DR was top of mind for many of the attendees. Throughout this week, I have felt tremors, and many of the locals told me that these happen all the time.
Introduction to IBM Storwize V7000
I knew I was in trouble when the request for me to present Storwize sounded like something from [Mission Impossible]:
"Good morning, Mr. Pearson. Your mission, should you choose to accept it, involves presenting Storwize V7000 in Auckland, New Zealand. You may also present the Storwize V7000 Unified, but it is essential that you not cover the SAN Volume Controller or SONAS products from which they are based upon, as you will not have enough time. The audience is very technical, so be careful. As always, should any questions come up that you cannot answer, the conference coordinators will disavow all knowledge of your actions, nor reimburse your laundry charges. This message will self-destruct in five seconds."
Well, I accomplished my mission in 75 minutes. I was able to cover the block-only version of the IBM Storwize V7000, with support for clustering the control enclosures, expansion drawers and external storage virtualization. I then spent a few minutes on the block-and-file Storwize V7000 Unified, which adds support for CIFS, NFS, HTTPS, FTP and SCP protocols through two new "file modules", with integrated support for backup and anti-virus checking. I covered both IBM Easy Tier for sub-LUN automated tiering between Solid-State Drives (SSD) and spinning disk, as well as Active Cloud Engine for file-based movement between disk and tape.
I always try to catch a session from Jim Blue, who works in our "SAN Central" center of competency team. This session was a long list of useful hints and tips, based on his many years of experience helping clients.
SAN Zoning works by inclusion, limiting the impact of failing devices. The best approach is to zone by individual initiator port. The default policy for your SAN zoning should be "deny".
Ports should be named to identify who, what, where and how.
While many people know not to mix both disk and tape devices on the same HBA, Jim also recommends not mixing dissimilar disks, test and production, FCP and FICON.
The sweet spot is FOUR paths. Too many paths can impact performance.
When making changes to redundant fabrics, make changes to the first fabric, then allow sufficient time before making the same changes to the other fabric.
Use software tools like Tivoli Storage Productivity Center (Standard Edition) to validate all changes to your SAN fabric.
Do not mix 62.5 and 50.0 micron technology.
Use port caps to disable inactive ports. In one amusing anecdote, he mention that an uncovered port was hit by sunlight every day, sending error messages that took a while to figure out.
Save your SAN configuration to non-SAN storage for backup
Consider firmware about two months old to be stable
Rule of thumb for estimating IOPS: 75-100 IOPS per 7200 RPM drive, 120-150 IOPS per 10K RPM drive, and 150-200 IOPS per 15K RPM drive.
Decide whether your shop is just-in-time or just-in-case provisioning. Just-in-time gets additional capacity on demand as needed, and just-in-case over-provisions to avoid scrambling last minute.
Avoid oversubscribing your inter-switch links (ISL). Aim for around 7:1 to 10:1 ratio.
Don't go cheap on bandwidth between sites for long-distance replication
Next Generation Network Fabrics - Strategy and Innovations
Mike Easterly, IBM Director of Global Field Marketing, presented IBM System Networking strategy, in light of IBM's recent acquisition of Blade Network Technologies (BNT). BNT is used in 350 of the Fortune 500 companies, and is ranked #2 behind Cisco in sales of non-core Ethernet switches (based on number of units sold).
Based on a recent survey, companies are upgrading their Ethernet networks for a variety of reasons:
56 percent for Live Partition Mobility and VMware Vmotion
45 percent for integrated compute stacks, like IBM CloudBurst
43 percent for private, public and hybrid cloud computing deployments
40 percent for network convergences
Many companies adopt a three-level approach, with core directors, distribution switches, and then access switches at the edge that connect servers and storage devices. IBM's BNT allows you to flatten the network to lower latency by collapsing the access and distribution levels into one.
IBM's strategy is to focus on BNT for the access/distribution level, and to continue its strategic partnerships for the core level.
IBM BNT provides better price/performance and lower energy consumption. To help with hot-aisle/cold-aisle rack deployments, IBM BNT provides both F and R models. F models have ports on the front, and R models have ports in the rear.
IBM BNT supports virtual fabric and HW-offload iSCSI traffic, and future-enabled for FCoE. Support for TRILL (transparent interconnect of lots of links) and OpenFlow will be implemented through software updates to the switches.
While Cisco Nexus 1000v is focused on VMware Enterprise Plus, IBM BNT's VMready works with VMware, Hyper-V, Linux KVM, XEN, OracleVM, and PowerVM. This allows single pane of management of VMready and ESX vSwitches.
In preparation for Converged Enhanced Ethernet (CEE), IBM BNT will provide full 40GbE support sometime next year, and offer switches that support 100GbE uplinks. IBM offers extended length cables, including passive SFP+ DAC at 8.5 meters, and 10Gbase-T Cat7 cables up to 100 meters.
Inter-datacenter Workload Mobility with VMware vSphere and SAN Volume Controller (SVC)
This session was co-presented between Bill Wiegand, IBM Advanced Technical Services, and Rawley Burbridge, IBM VMware and midrange storage consultant. IBM is the leader in storage virtualization product (SVC), and is the leading reseller of VMware.
Like MetroCluster on IBM N series, or EMC's VPLEX Metro, the IBM SAN Volume Controller can support a stretched cluster across distance that allows virtual machines to move seamlessly from one datacenter to another. This is a feature IBM introduced with SVC 5.1 back in 2009. This can be used for PowerVM Live Partition Mobility, VMware vMotion, and Hyper-V Quick Migration.
SVC stretched cluster can help with both Disaster Avoidance and Disaster Recovery. For Disaster Avoidance, in anticipation of an outage, VMs can be moved to the secondary datacenter. For Disaster Recover, additional automation, such as VMware High Availability (HA) is needed to restart the VMs at the secondary datacenter.
IBM stretched cluster is further improved with a feature called Volume Mirroring (formerly vDisk Mirroring) which creates two physical copies of one logical volume. To the VMware ESX hosts, there is only one volume, regardless of which datacenter it is in. The two physical copies can be on any kind of managed disk, as there is no requirement or dependency of copy services on the back-end storage arrays.
Another recent improvement is the idea of spreading the three quorum disks to three different locations or "failure domains". One in each data center, and a third one in a separate building, somewhere in between the other two, perhaps.
Of course, there are regional disasters that could affect both datacenters. For this reason, SVC stretched cluster volumes can be replicated to a third location up to 8000 km away. This can be done with any back-end disk arrays, as again there is not requirement for copy services from the managed devices. SVC takes care of it all.
Networking is going to be very important for a variety of transformational projects going forward in the next five years.
Jim is an IBM Fellow for IBM Systems and Technology Group. There are only 73 IBM Fellows currently working for IBM, and this is the highest honor IBM can bestow on an employee. He has been working with IBM since 1968.
He is tasked with predicting the future of IT, and help drive strategic direction for IBM. Cost pressures, requirements for growth, accelerating innovation and changing business needs help influence this direction.
IBM's approach is to integrate four different "IT building blocks":
Scale-up Systems, like the IBM System Storage DS8000 and TS3500 Tape Library
Resource Pools, such as IBM Storage Pools formed from managed disks by IBM SAN Volume Controller (SVC)
Integrated stacks and appliances, integrated software and hardware stacks, from Storwize V7000 to full rack systems like IBM Smart Analytics Server or CloudBurst.
Mobility of workloads and resources requires unified end-to-end service management. Fortunately, IBM is the #1 leader in IT Service Management solutions.
Jim addressed three myths:
Myth 1: IT Infrastructures will be homogenous.
Jim feels that innovations are happening too rapidly for this to ever happen, and is not a desirable end-goal. Instead, a focus to find the right balance of the IT building blocks might be a better approach.
Myth 2: All of your problems can be solved by replacing everything with product X.
Jim feels that the days of "rip-and-replace" are fading away. As IBM Executive Steve Mills said, "It isn't about the next new thing, but how well new things integrate with established applications and processes."
Myth 3: All IT will move to the Cloud model.
Jim feels a substantial portion of IT will move to the Cloud, but not all of it. There will always be exceptions where the old traditional ways of doing things might be appropriate. Clouds are just one of the many building blocks to choose from.
Jim's focus lately has been finding new ways to take advantage of virtualization concepts. Server, storage and network virtualization are helping address these challenges through four key methods:
Sharing - virtualization that allows a single resource to be used by multiple users. For example, hypervisors allow several guest VM operating systems share common hardware on a single physical server.
Aggregation - virtualization that allows multiple resources to be managed as a single pool. For example, SAN Volume Controller can virtualize the storage of multiple disk arrays and create a single storage pool.
Emulation - virtualization that allows one set of resources to look and feel like a different set of resources. Some hypervisors can emulate different kinds of CPU processors, for example.
Insulation - virtualization that hides the complexity from the end-user application or other higher levels of infrastructure, making it easier to make changes of the underlying managed resources. For example, both SONAS and SAN Volume Controller allow disk capacity to be removed and replaced without disruption to the application.
In today's economy, IT transformation costs must be low enough to yield near-term benefits. The long-term benefits are real, but near-term benefits are needed for projects to get started.
What set's IBM ahead of the pack? Here was Jim's list:
100 Years of Innovation, including being the U.S. Patent leader for the last 18 years in a row
IBM's huge investment in IBM Research, with labs all over the globe
Leadership products in a broad portfolio
Workload-optimized designs with integration from middleware all the way down to underlying hardware
Comprehensive management software for IBM and non-IBM equipment
Clod is an IBM Distinguished Engineer and Chief Technical Strategist for IBM System Storage. His presentation focused on trends and directions in the IT storage industry. Clod started with five workload categories:
To address these unique workload categories, IBM will offer workload-optimized systems. The four drivers on the design for these are performance, efficiency, scalability, and integration. For example, to address performance, companies can adopt Solid-State Drives (SSD). Unfortunately, these are 20 times more expensive dollar-per-GB than spinning disk, and the complexity involved in deciding what data to place on SSD was daunting. IBM solved this with an elegant solution called IBM System Storage Easy Tier, which provides automated data tiering for IBM DS8000, SAN Volume Controller (SVC) and Storwize V7000.
For scalability, IBM has adopted Scale-Out architectures, as seen in the XIV, SVC, and SONAS. SONAS is based on the highly scalable IBM General Parallel File System (GPFS). File systems are like wine, they get better with age. GPFS was introduced 15 years ago, and is more mature than many of the other "scalable file systems" from our competition.
Areal Density advancements on Hard Disk Drives (HDD) are slowing down. During the 1990s, the IT industry enjoyed 60 to 100 percent annual improvement in areal density (bits per square inch). In the 2000s, this dropped to 25 to 40 percent, as engineers are starting to hit various physical limitations.
Storage Efficiency features like compression have been around for a while, but are being deployed in new ways. For example, IBM invented WAN compression needed for Mainframe HASP. WAN compression became industry standard. Then IBM introduced compression on tape, and now compression on tape is an industry standard. ProtecTIER and Information Archive are able to combine compression with data deduplication to store backups and archive copies. Lastly, IBM now offers compression on primary data, through the IBM Real-Time Compression appliance.
For the rest of this decade, IBM predicts that tape will continue to enjoy (at least) 10 times lower dollar-per-GB than the least expensive spinning disk. Disk and Tape share common technologies, so all of the R&D investment for these products apply to both types of storage media.
For integration, IBM is leading the effort to help companies converge their SAN and LAN networks. By 2015, Clod predicts that there will be more FCoE purchased than FCP. IBM is also driving integration between hypervisors and storage virtualization. For example, IBM already supports VMware API for Array Integration (VAAI) in various storage products, including XIV, SVC and Storwize V7000.
Lastly, Clod could not finish a presentation without mentioning Cloud Computing. Cloud storage is expected to grow 32 percent CAGR from year 2010 to 2015. Roughly 10 percent of all servers and storage will be in some type of cloud by 2015.
As is often the case, I am torn between getting short posts out in a timely manner versus spending some more time to improve the length and quality of information, but posted much later. I will spread out the blog posts in consumable amounts throughout the next week or two, to achieve this balance.
Mastering the art of stretching out a week-long event into two weeks' worth of blog posts, I continue my
coverage of the [Data Center 2010 conference], Tuesday afternoon I attended several sessions that focused on technologies for Cloud Computing.
(Note: It appears I need to repeat this. The analyst company that runs this event has kindly asked me not to mention their name on this blog, display any of their logos, mention the names of any of their employees, include photos of any of their analysts, include slides from their presentations, or quote verbatim any of their speech at this conference. This is all done to protect and respect their intellectual property that their members pay for. The pie charts included on this series of posts were rendered by Google Charting tool.)
Converging Storage and Network Fabrics
The analysts presented a set of alternative approaches to consolidating your SAN and LAN fabrics. Here were the choices discussed:
Fibre Channel over Ethernet (FCoE) - This requires 10GbE with Data Center Bridging (DCB) standards, what IBM refers to as Converged Enhanced Ethernet (CEE). Converged Network Adapters (CNAs) support FC, iSCSI, NFS and CIFS protocols on a single wire.
Internet SCSI (iSCSI) - This works on any flavor of Ethernet, is fully routable, and was developed in the 1990s by IBM and Cisco. Most 1GbE and all 10GbE Network Interface Cards (NIC) support TCP Offload Engine (TOE) and "boot from SAN" capability. Native suppot for iSCSI is widely available in most hypervisors and operating systems, including VMware and Windows. DCB Ethernet is not required for iSCSI, but can be helpful. Many customers keep their iSCSI traffic in a separate network (often referred to as an IP SAN) from the rest of their traditional LAN traffic.
Network Attached Storage (NAS) - NFS and CIFS have been around for a long time and work with any flavor of Ethernet. Like iSCSI, DCB is not required but can be helpful. NAS went from being for files only, to be used for email and database, and now is viewed as the easiest deployment for VMware. Vmotion is able to move VM guests from one host to another within the same LAN subnet.
Infiniband or PCI extenders - this approach allows many servers to share fewer number of NICs and HBAs. While Infiniband was limited in distance for its copper cables, recent advances now allow fiber optic cables for 150 meter distances.
Interactive poll of the audience offered some insight on plans to switch from FC/FICON to Ethernet-based storage:
Interactive poll of the audience offered some insight on what portion storage is FCP/FICON attached:
Interactive poll of the audience offered some insight on what portion storage is Ethernet-attached:
Interactive poll of the audience offered some insight on what portion of servers are already using some Ethernet-attached storage:
Each vendor has its own style. HP provides homogeneous solutions, having acquired 3COM and broken off relations with Cisco. Cisco offers tight alliances over closed proprietary solutions, publicly partnering with both EMC and NetApp for storage. IBM offers loose alliances, with IBM-branded solutions from Brocade and BNT, as well as reselling arrangements with Cisco and Juniper. Oracle has focused on Infiniband instead for its appliances.
The analysts predict that IBM will be the first to deliver 40 GbE, from their BNT acquisition. They predict by 2014 that Ethernet approaches (NAS, iSCSI, FCoE) will be the core technology for all but the largest SANs, and that iSCSI and NAS will be more widespread than FCoE. As for cabling, the analysts recommend copper within the rack, but fiber optic between racks. Consider SAN management software, such as IBM Tivoli Storage Productivity Center.
The analysts felt that the biggest inhibitor to merging SAN and LANs will be organizational issues. SAN administrators consider LAN administrators like "Cowboys" undisciplined and unwilling to focus on 24x7 operational availability, redundancy or business continuity. LAN administrators consider SAN administrators as "Luddites" afraid or unwilling to accept FCoE, iSCSI or NAS approaches.
Driving Innovation through Innovation
Mr. Shannon Poulin from Intel presented their advancements in Cloud Computing. Let's start with some facts and predictions:
There are over 2.5 billion photos on Facebook, which runs on 30,000 servers
30 billion videos viewed every month
Nearly all Internet-connected devices are either computers or phones
An additional billion people on the Internet
Cars, televisions, and households will also be connected to the Internet
The world will need 8x more network bandwidth, 12x more storage, and 20x more compute power
To avoid confusion between on-premise and off-premise deployments, Intel defines "private cloud" as "single tenant" and "public cloud" as "multi-tenant". Clouds should be
automated, efficient, simple, secure, and interoperable enough to allow federation of resources across providers. He also felt that Clouds should be "client-aware" so that it know what devices it is talking to, and optimizes the results accordingly. For example, if watching video on a small 320x240 smartphone screen, it makes no sense for the Cloud server to push out 1080p. All devices are going through a connected/disconnected dichotomy. They can do some things while disconnected, but other things only while connected to the Internet or Cloud provider.
An internal Intel task force investigated what it would take to beat MIPS and IBM POWER processors and found that their own Intel chips lacked key functionality. Intel plans to address some of their shortcomings with a new chip called "Sandbridge" sometime next year. They also plan a series of specialized chips that support graphics processing (GPU), network processing (NPU) and so on. He also mentioned Intel released "Tukwilla" earlier this year, the latest version of Itanium chip. HP is the last major company to still use Itanium for their servers.
Shannon wrapped up the talk with a discussion of two Cloud Computing initiatives. The first is [Intel® Cloud Builders], a cross-industry effort to build Cloud infrastructures based on the Intel Xeon chipset. The second is the [Open Data Center Alliance], comprised of leading global IT managers who are working together to define and promote data center requirements for the cloud and beyond.
The analysts feel that we need to switch from thinking about "boxes" (servers, storage, networks) to "resources". To this end, they envision a future datacenter where resources are connected to an any-to-any fabric that connects compute, memory, storage, and networking resources as commodities. They feel the current trend towards integrated system stacks is just a marketing ploy by vendors to fatten their wallets. (Ouch!)
A new concept to "disaggregate" caught my attention. When you make cookies, you disaggregate a cup of sugar from the sugar bag, a teaspoon of baking soda from the box, and so on. When you carve a LUN from a disk array, you are disaggregating the storage resources you need for a project. The analysts feel we should be able to do this with servers and network resources as well, so that when you want to deploy a new workload you just disaggregate the bits and pieces in the amounts you actually plan to use and combine them accordingly. IBM calls these combinations "ensembles" of Cloud computing.
Very few workloads require "best-of-breed" technologies. Rather, this new fabric-based infrastructure recognizes the reality that most workloads do not. One thing that IT Data Center operations can learn from Cloud Service Providers is their focus on "good enough" deployment.
This means however that IT professionals will need new skill sets. IT administrators will need to learn a bit of application development, systems integration, and runbook automation. Network adminis need to enter into 12-step programs to stop using Command Line Interfaces (CLI). Server admins need to put down their screwdrivers and focus instead on policy templates.
Whether you deploy private, public or hybrid cloud computing, the benefits are real and worth the changes needed in skill sets and organizational structure.
Well, it's Tuesday again, and that means IBM announcements! Today we had a major launch, with so many products, services and offerings
that I can't fit them all into a single post, so I will split them up into several posts to give the attention they deserve. So, in this
post, I will focus on just the networking gear.
IBM Converged Switch B32
The "Converged" part of this switch refers to Converged Enhanced Ethernet (CEE), which is just a lossless Ethernet that meets certain standards to allow Fibre Channel over Ethernet (FCoE) that are still being discussed between Brocade and Cisco. Thankfully, IBM demanded both Brocade and Cisco stick to open agreed-upon standards, and the rest of the world gets to benefit from IBM's leadership in keeping everything as open and non-proprietary as possible.
The B32 ("B" because it was made by Brocade) starts with 24 10Gb Converged Enhanced Ethernet (CEE) ports, and then you can add eight Fibre Channel ports, for a total of 32 ports, hence the name B32. These are designed to be Top-of-Rack (TOR) switches. Basically, instead of having expensive optical cables for Ethernet and/or Fibre Channel out of each server, you have cheap twinax copper cables connecting the server's Converged Network Adapters (CNA) to this TOR switch, and then you can have the 10Gb Ethernet go to your regular Ethernet LAN, and your 8Gbps FC traffic go to your regular FC SAN. In other words, the CNA serves both the role of an Ethernet Network Interface Card (NIC) as well as a Fibre Channel Host Bus Adapter (HBA) card.
(You might see 8Gbps Fibre Channel represented as 8/4/2 or 2/4/8, this is just to remind you that these 8Gb FC ports can auto-negotiate down to 2Gbps and 4Gbps legacy hardware, but not 1Gbps. If you are still using 1Gbps FC, you need 4Gpbs SFP transceivers instead, shown often as 1/2/4 or 4/2/1.)
New SSN-16 module for Cisco directors and switches
When I present SAN gear to sales reps, I often get the question, "What is the difference between a switch and a director?" My quick and simple answer is that switches have fixed ports, but directors have slots that you can slide in different blades or expansion modules. The Cisco MDS9500 series are directors with slots, the three models provide a hint to their capacity. The last two digits represent the number of total slots, but the first two slots are already taken. In other words, model 9513 has 11 slots, model 9509 has seven slots, and model 9506 has four slots. You can have a 48-port blade in a slot, so in theory, you can have a maximum of 528 ports on the biggest model 9513.
However, if you want FCIP for disaster recovery, or I/O Acceleration (IOA) for remote e-vaulting tape libraries, you need a special 18/4 blade. This has 18 FC ports, four 1GbE ports and a special service processor that speaks FCIP or IOA. If you wanted two service processors for FCIP and two for IOA, you would need four of these blades, and that takes up slots that could have been used for 48-port blades instead. The solution? The new SSN-16 has sixteen 1GbE ports and four service processors, so with one slot, you can handle the FCIP and IOA processing that you previously used four cards, giving you three slots back to use with higher port-density cards.
Even better, you can put this new SSN-16 in the Cisco 9222i. The model 9222i is a "hybrid" switch with 22 fixed ports (18 FC ports, four fixed 1GbE ports, and a service processor, so basically the fixed port version of the 18/4 blade above), but it also has one slot! That one slot can be used for the SSN-16 to give you added FCIP or IOA capability.
For our mainframe clients, the FICON package includes four 24-port FICON blades and 96 SFP 4Gbps transceivers to fully populate them. Here is the IBM [Press Release].
Cisco Nexus 5000 series for IBM System Storage
The Cisco Nexus 5000 series is Cisco's entry into the Converged Enhanced Ethernet world, although Cisco sometimes refers to this as Data Center Ethernet (DCE), IBM will continue to use CEE when referring to either Brocade and Cisco gear. These are also Top-of-Rack aggregators that support CNA connections over cheaper twinax copper wires. Model 5010 has 10 ports that can be configured for either 1GbE or 10Gb CEE, 10 ports that are 10Gb CEE, and a slot for an expansion module. The Model 5020 has basically twice as much of everything, including two slots instead of one. Since 10Gb Ethernet does not auto-negotiate down to 1GbE, half the ports can be configured to run 1GbE instead. Frankly, that can be seen as wasting your precious Nexus ports with 1GbE connections, so you might find a 1GbE-to-10GbE aggregator that combines a dozen or more 1GbE to a few 10GbE links instead.
Today's announcement is that in addition to 10GbE and 4Gbps FC expansion modules, there is now an expansion module that supports 8Gbps Fibre Channel. Here is the IBM [Press Release].
Whether you choose Brocade or Cisco, nearly all of IBM System Storage disk and tape products can work today with Converged Enhanced Ethernet environments, either directly using iSCSI, NFS or CIFS, or using the FCoE methodology.
As you can see, it took me a whole post just to cover just our networking gear announcements, and I haven't even covered our disk, tape and cloud storage offerings. I'll get to these in later posts.
Continuing my coverage of the Data Center Conference, held Dec 1-4 in Las Vegas, an analyst presented the challenges of managing the rapid growth in storage capacity. Administrators ability to manage storage is not keeping up with the growth. His recommendations:
Aim to just meet but not exceed service level agreements (SLAs)
Revisit past IT decisions. This includes evaluating your SAN to NAS ratio.
Embrace new technologies when they are effective, this includes cloud storage, solid state drives, and interconnect technologies like FCoCEE.
Follow vendor management best practices, update your vendor "short list".
A survey of the audience found:
20 percent have a single external storage vendor
39 percent have two external storage vendors
18 percent have three external storage vendors
23 percent have four or more external storage vendors
Throughout the industry, storage vendors are following IBM's example of using commodity hardware parts. This is because custom ASICs are expensive, and changes take a minimum of three months development time. Software-based implementations can be updated more quickly.
In terms of technologies deployed of SAN, NAS, Compliance Archive (such as the IBM Information Archive), and Virtual Tape Library (VTL) such as the IBM TS7650 ProtecTIER data deduplications solution, here was the survey of the audience:
8 percent: SAN only
14 percent: SAN and NAS
23 percent: SAN, NAS and Compliance Archive
9 percent: SAN and VTL
14 percent: SAN, NAS and VTL
32 percent: SAN, NAS, Compliance Archive and VTL
Cost reduction techniques including thin provisioning, compression, data deduplication, Quality of Service tiers, and archiving. To reduce power and cooling requirements, switch from FC to SATA disk wherever possible, and move storage out of the data center, such as on tape cartridges or cloud storage.
For emerging technologies, the following survey:
16 percent have already implemented a new emerging technology (IBM XIV, Pillar, 3PAR, etc.)
30 percent plan to do so in 12-24 months
4 percent plan to do so in 24-48 months
50 percent have no plans, and will continue to stick with traditional storage technologies
As for adopting Cloud storage, here was the survey:
14 percent already have
31 percent plan to use Cloud storage in 12-24 months
13 percent plan to use Cloud storage in 24-48 months
42 percent have no plans to adopt Cloud storage
My take-away from this is that many companies are still "exploring" into different options available to them. Fortunately, IBM offers a broad portfolio of complete end-to-end solutions to make acquiring the right mix of technologies that are optimized for your workloads possible.
The "Storage Symposium Mexico - 2008" conference was a great success this week!
Day 1 - The plan was for me to arrive for the Wednesday night reception. Eachattendee was given a copy of my latest book[Inside System Storage: Volume I] and I was planning to sign them. I thought perhaps we should have a "book signing" tablelike all of the other published authors have.
Things didn't go according to plan. Thunderstorms at the Mexico City airport forced our pilot to find an alternate airport. Nearby Acapulco airport was the logical choice, but was full from all the otherflights, so the plane ended up in a tiny town called McAllen, Texas. I did not arrive until the morning of Day 2,so ended up signing the books throughout Thursday and Friday, during breaks and meals, wherever they couldfind me!
Special thanks to fellow IBMer Ian Henderson who picked me up from the airport at such an awkward hour anddrive me all the way to Cuernavaca!
All of us, IBMers, Business Partners and clients alike, all donned black tee-shirtswith a white eightbar logo for a group photo with one of those "wide lens" cameras. While we werebeing assembled onto the bleachers, I took this quick snapshot of myself and some of the guys behind me.
I was original scheduled to be first to speak, but with my flight delays, was moved to a time slot after lunch.After a big Mexican lunch, the conference coordinators were afraid the attendees might fall asleep,a Mexican tradition called [siesta], so I wasinstructed to WAKE THEM UP! Fortunately, my topic was Information Lifecycle Management, a topicI am very passionate about, since my days working on DFSMS on the mainframe. With 30percent reduction in hardware capital expenditures, 30 percent reduction in operational costs, and typical payback periods between 15 to 24 months, the presentation got everyone's attention.
Of course, a lot happens outside of the formal meetings. We had a Japanese theme dinner, where we woreJapanese Hachimaki [headbands]with the eightbar logo. For those not familiar with Japanese culture, hachimaki are worn today not so much for the practical purpose to catch the perspiration but rather for mental stimulation to express one's determination. Some students wear hachimaki when they study to put themselves in the right spirit and frame of mind.
Shown here are presenters Mike Griese (Infrastructure Management with IBM TotalStorage Productivity Center),Dave Larimer (Backup and Storage Management with IBM Tivoli Storage Manager), myself, and John Hamano(Unified Storage with IBM System Storage N series).
Day 3 - Wrapping up the week, I presented two more times.
First, I covered IBM Disk Virtualization with IBM SAN Volume Controller. One interesting question was if the SAN Volume Controller could be made to looklike a Virtual Tape Library. I explained that this was never part of the original design, but that if you wantto combine SVC with a VTL into a combined disk-and-tape blended solution, consider using theIBM product called Scale-Out File Services[SoFS] which I covered in my post[Moredetails about IBM clustered scalable NAS].
During one of the breaks, I took a picture of the behind-the-scenes staff that put this together. They had created these huge blocks representing puzzle pieces, emphasizing how IBM is one of the few ITvendors that can bring all the pieces together for a complete solution.
Shown hereare Mike Griese (presenter), Cyntia Martinez, Claudia Aviles, Cesar Campos (IBM Business Unit Executive forSystem Storage in Mexico), and Claudia Lopez. Each day the staff wore matching shirts so that it was easyto find them.
Later, I covered Archive and Compliance Solutions to highlight our complete end-to-end set of solutions.When asked to compare and contrast the architectures of the IBM System Storage DR550 with EMC Centera, I explainedthat the DR550 optimizes the use of online disk access for the most recent data. For example, if you aregoing to keep data for 10 years, maybe you keep the most recent 12 months on disk, and the rest is moved,using policy-based automation, to a tape library for the remaining nine years. This means that the disk insidethe DR550 is always being used to read and write the most recent data, the data you are most likely to retrievefrom an archive system. Data older than a year is still accessible, but might take a minute or two for the tapelibrary robot to fetch.The EMC Centera, on the other hand, is a disk-only solution. It offers no option to move older data to tape,nor the option to spin-down the drives to conserve power. It fills up after the same 12 months or so, and then you get towatch it the remaining nine years, consuming electricity and heating your data center.
I don't know about you, butI have never seen anyone purposely put in "space heaters" into their data center, but certainly a full EMC Centeradoes little else. Both devices use SATA drives and support disk mirroring between locations, but IBM DR550 offers dual-parity RAID-6, and supports encryption of the data on both the disk and the tape in the DR550. EMC Centerastill uses only RAID-5, and has not yet, as far as I know, offered any level of encryption. IBM System StorageDR550 was clocked at about three times faster than Centera at ingesting new archive objects over a 1GbE Ethernet connection.
This last photo is me and fellow IBMer Adriana Mondragón. She was one of my students in the [System Storage Portfolio Top Gun class],last February in Guadalajara, Mexico.She graduated in the top 10 percent of her group, earning her the prestigious titleof "Top Gun" storage sales specialist.
The conference wrapped up with a Mexican lunch with a traditional Mariachi band. I took pictures, but figured you allalready know what [Mariachi players] look like, and I didn't wantto detract from the otherwise serious tone of this blog post! This was the first System Storage Symposium in Mexico, butbased on its success, we might continue these annually.
Yesterday, I asked if you were prepared for the future? The future is now. Today, IBM announced its["New Enterprise Data Center"] vision and strategy which spans software, hardware and services in dealing withthe latest challenges that our clients are faced with today, or will face sooner or later this century.
Here's an excerpt:
Align IT with business goals These changes demand that IT improve cost and service delivery, manage escalating complexity, and better secure the enterprise. And aligning IT more closely with the business becomes a primary goal. The new enterprise data center is an evolutionary new model for efficient IT delivery that helps provide the freedom to drive business innovation. Through a service oriented model, IT will be able to better manage costs, improve operational performance and resiliency, and more quickly respond to business needs. This approach will deliver dynamic and seamless access to IT services and resources, improving both productivity and satisfaction.
IBM's Vision for the New Enterprise Data Center The new enterprise data center can improve the integration of people, process, and technology in your business to help you improve efficiency and effectiveness. As you implement a new enterprise data center strategy, your infrastructure becomes open, efficient, and easy to manage. And your IT staff can move from a focus on fixing IT problems to solving business challenges. Ultimately your processes become standardized and efficient, focused on business needs rather than technology.
A lot was announced today, so I will give a quick recap now, and cover specific areas over the rest of the week.
IBM System z10 Enteprise Class
IBM introduces its most powerful mainframe. Before you think "Wait, that's a mainframe, that doesn't apply to me"stop to consider all that IBM has done to make the mainframe an "open system" without sacrificing security oravailability:
Open standard connectivity, including TCP/IP and now 6Gbps Infiniband and 10GbE Ethernet.
Unix System Services. Yes, z/OS is certified to provide UNIX interfaces for today's applications.
HFS and zFS file systems that can be mounted, shared, and used by traditional z/OS applications and JCL.
Linux and Java. Many of today's largest websites are run on mainframes behind the scenes.
Extreme bandwidth. The z10 EC handles up to 336 FICON channels (4Gbps) for large data processing workloads
The z10 EC is as powerful as 1,500 x86 (such as Intel or AMD) servers, but consumes 85 percent less floorspace and85 percent less energy. (They should put a "green" stripe down the front of this box just to remind everyone how energy efficient this server really is!) For more on the z10 EC, see the[Press Release].
Enhanced IBM System Storage DS8000
With the XIV acquisition taking the role as the best place to put unstructured files for Web 2.0 applications,the IBM DS8000 can focus on its core strength, managing databases and online transactions for the mainframe.There's enough here to justify its own post, so I will cover this later.
IT Service Management Center for z (ITSMCz)
Trust me, I don't make up these acronyms. IT Service Management are the policies and procedures for managingan IT environment, such as following the best practices documented in the IT Infrastructure Library (ITIL).In the past, IBM tools have focused on Linux, UNIX and Windows on distributed servers, but today ITSMCz bringsall of that to the mainframe! (or perhaps more correct to say "brings the mainframe to all that"!)
IT Transformation & Optimization - Infrastructure Strategy and Planning services
I don't make up the names of our service offerings either. However, one thing is clear, it is time for peopleto re-evaluate their current data center, and come up with a new plan. The average data center is 15 years old.According to Gartner Group, more than 70 percent of the world's "Global 1000" organizations will have to make significant modifications to their data centers in the next five years. IBM can help, and is rolling outa new set of services specifically to help clients make this transition, to better align their IT to their business strategies.
Economic Stimulus Package
IBM borrowed this idea from the U.S. government. IBM Global Financing is offering special terms and ratesfor new equipment installed by December 31 this year.
Want to learn more? Read this 15-page[IBM's Vision]white paper.
Yesterday, I promised I would cover other products from the Feb 12 announcement. Today I will focus on the IBM SAN768B director. Some people are confused on the differences between switchesand directors. I find there are three key differences:
Directors are designed to be 24x7 operation, highly available with no single points of failure or repair. Generally, all components in directors are redundant and hot-swappable, including Control Processors. In switches, some components are redundant and hot-swappable, such as fans and power supplies), but not the “motherboard” or controller. Often you have to take down a switch to make firmware or major hardware changes or upgrades.
Directors are designed to take in "blades" with different features, port counts, or protocol capabilities. You can add or remove blades while the system is up and running. Switches have a fixed number of ports. (A Small Form-factor Pluggable optical transceiver [SFP] is the component that turns electric pulses into light pulses (and visa versa). You plug the SFP into the switch, and then the fiber optic cable is plugged into the SFP).
With switches, you often start with a base number of active ports, and then can enable the rest of the ports as you need them.
Directors have hundreds of ports. Switches tend to have 64 ports or less.
Last year, Brocade acquired McDATA. Both were OEMs for IBM, and IBM distinguished that in the naming convention. The IBM SAN***B name was used to denote products manufactured for IBM by Brocade, and a SAN***M name was used to denote products manufactured by McDATA.
At that time, Brocade and McDATA equipment did not mix very well on the same fabric, so IBM retained the naming convention so that you as a customer knew what it worked with.
Brocade now has released with new levels of both operating systems--Brocade's FOS and McDATA's EOS--and their respective fabric managers--Brocade Fabric Manager (FM) and McDATA's Enterprise Fabric Connectivity Manager (EFCM)--so that they have full interoperability.
Brocade's goal is to enhance EFCM to be a common software management platform for all of their products going forward.
IBM used the maximum port count in the name to provide some clue as to the size of the switch or director. The SAN16B-2 or the SAN32B-3 are switches that have a maximum of 16 and 32 ports. The SAN256B supports a maximumeight blades of your choosing.Two different types were supported for FC ports, a 16-port blade and a 32-port blade.If all eight were 32-port blades then the maximum was 256 ports, hence the name. But then Brocade began offering 48-port blades. Should IBM change the name? No, it decided to leave itthe SAN256B even though it can now have a maximum of 384 ports.
Not to confuse anyone, the SAN768B also has a maximum of 384 ports, in the same 14U dimensions, but with a special twist. Normally to connect two directors together you use up ports from each, in what are called "inter-switch links" (ISL).These are ports you are taking away from availability from the servers and storage controllers. The SAN768Boffers a new alternative called "inter-chassis links". Each SAN768B has two processing blades, and each has two ICL ports, so with just four two-meter (2m) cables, you get the equivalent of 128 FC 8 Gbps ISL links without using 128 individual ports on each side. That is like giving you 256 ports back for use with servers and storage!
Since IBM directors require 240 volt power, IBM TotalStorage SAN Cabinet C36 include power distribution units (PDUs). PDUs are just glorified power strips, but a new intelligent PDU (iPDU) option introduces additional intelligence to monitor energy consumption for customers looking to measure, and perhaps charge back, energy consumption to the rest of the business. You can stack two SAN768B in one cabinet, one on top of the other, and connected via ICLs, it wouldlook like one huge 768-port backbone.
As a backbone for your data center, the SAN768B is positioned for two emerging technologies:
8 Gbps Fibre Channel (FC)
The SAN768B is powerful enough to have 32-port blades run full speed on all ports off-blade without oversubscription. Oversubscription is an emotional topic.
Normally, blades (like switches) can handle all traffic at full speed without delays provided the in-bound and out-bound ports involved are all on the same blade. In a director, however, if you need to communicate from a port on one blade to a port on a different blade, it is possible that off-blade traffic might be constrained or delayed in its transit across the backplane.
On the SAN768B, both the 16-port and 32-port blades can run at full 8 Gbps speed, and the 48-port is exposed to oversubscription only if you have more than 32-ports running at full 8 Gbps transferring data off-blade concurrently.
The new 8 Gbps SFPs support auto-negotiation at N-1 and N-2 generation link speeds. This means that they will automatically slow down when communicating with 4Gpbs and 2 Gbps devices, but they cannot communicate with 1 Gbps devices. If you are still using 1 Gbps devices in your data center, you will need to use 4 Gbps SFPs (which also support 2 Gbps and 1 Gbps link speeds) to communicate with those older devices.
Basically, this new technology enables transport of Fibre Channel packets over 10 Gbps Ethernet links. This 10 Gbps Ethernet can also be used to carry traditional iSCSI and TCP/IP traffic. FCoE introduces new extensions to provide Fibre Channel characteristics, like being lossless, and offering consistent performance. The ANSI T11 team is driving FCoE as an open standard, and at the moment it is not fully baked. I suggest you don't buy any FCoE equipment prematurely, as pre-standard devices or host bus adapters could get you burned later when the standard is finalized.
The idea is that FCoE blades can be installed in a SAN768B along with traditional FC blades, allowing routing of traffic between traditional FC and new FCoE ports. Those who have invested in FCIP for long distance replication will be able to continue using either FC or FCoE inputs.
One of the big drivers of FCoE is IBM BladeCenter. Currently, most BladeCenter blades support both Ethernet and FC connectivity and are connected to both Ethernet and FC switches on the back of each BladeCenter chassis. With FCoE, we have the potential to run both FC and IP traffic across simpler all-Ethernet blades, connecting through all-Ethernet switches on the backs of each chassis.
For more information on the IBM SAN768B, see the [IBM Press Release]. For more detailson Brocade's strategy, here is an 8-page white paper on their[Data Center Fabric] vision.
Many people have asked me if there was any logic with the IBM naming convention of IBM Systems branded servers. Here's your quick and easy cheat sheet:
System x -- "x" for cross-platform architecture. Technologies from our mainframe and UNIX servers were brought into chips that sit next to the Intel or AMD processors to provide a more reliable x86 server experience. For example, some models have a POWER processor-based Remote Supervisor Adapter (RSA).
System p -- "p" for POWER architecture.
System z -- "z" for Zero-downtime, zero-exposures. Our lawyers prefer "near-zero", but this is about as close as you get to ["six-nines" availability] in our industry, with the highest level of security and encryption, no other vendor comes close, so you get the idea.
But what about the "i" for System i? Officially, it stands for "Integrated" in that it could integrate different applications running on different operating systems onto a [COMMON] platform. Options were available to insert Intel-based processor cards that ran Windows, or attach special cables that allowed separate System x servers running Windows to attach to a System i. Both allowed Windows applications to share the internal LAN and SAN inside the System i machine. Later, IBM allowed [AIX on System i] and [Linux on Power] operating systems to run as well.
From a storage perspective, we often joked that the "i" stood for "island", as most System i machines used internal disk, or attached externally to only a fewselected models of disk from IBM and EMC that had special support for i5/OS using a special, non-standard 520-byte disk block size. This meant only our popular IBM System Storage DS6000 and DS8000 series disk systems were available. This block size requirement only applies to disk. For tape, i5/OS supports both IBM TS1120 and LTO tape systems. For the most part,System i machines stood separate from the mainframe, and the rest of the Linux, UNIX and Windows distributed serverson the data center floor.
Often, when I am talking to customers, they ask when will product xyz be supported on System z or System i?I explained that IBM's strategy is not to make all storage devices connect via ESCON/FICON or support non-standard block sizes, but rather to get the servers to use standard 512-byte block size, Fibre Channel and other standard protocols.(The old adage applies: If you can't get Mohamed to move to the mountain, get the mountain to move to Mohamed).
On the System z mainframe, we are 60 percent there, allowing three of the five operating systems (z/VM, z/VSE and Linux) to access FCP-based disk and tape devices. (Four out of six if you include [OpenSolaris for the mainframe])But what about System i? As the characters on the popular television show [LOST] would say: It's time to get off the island!
Last week, IBM announced the new [i5/OS V6R1 operating system] with features that will greatly improve the use of external storage on this platform. Check this out:
POWER6-based System i 570 model server
Our latest, most powerful POWER processor brought to the System i platform. The 570 model will be the first in the System i family of servers to make use of new processing technology, using up to 16 (sixteen!) POWER6 processors (running at 4.7GHZ) in each machine.The advantage of the new processors is the increased commercial processing workload (CPW) rating, 31 percent greater than the POWER5+ version and 72 percent greater than the POWER5 version. CPW is the "MIPS" or "TeraFlops" rating for comparing System i servers.Here is the[Announcement Letter].
Fibre Channel Adapter for System i hardware
That's right, these are [Smart IOAs], so an I/O Processor (IOP) is no longer required! You can even boot the Initial Program Load (IPL) direclty from SAN-attached tape.This brings System i to the 21st century for Business Continuity options.
Virtual I/O Server (VIOS)
[VirtualI/O Server] has been around for System p machines, but now available on System i as well. This allows multiplelogical partitions (LPARs) to access resources like Ethernet cards and FCP host bus adapters. In the case of storage, the VIOS handles the 520-byte to 512-byte conversion, so that i5/OS systems can now read and write to standard FCP devices like the IBM System Storage DS4800 and DS4700 disk systems.
IBM System Storage DS4000 series
Initially, we have certified DS4700 and DS4800 disk systems to work with i5/OS, but more devices are in plan.This means that you can now share your DS4700 between i5/OS and your other Linux, UNIX and Windowsservers, take advantage of a mix of FC and SATA disk capacities, RAID6 protection, and so on.
To call [IBM PowerVM] the "VMware for the POWER architecture" would not do it quite justice. In combination with VIOS, IBM PowerVM is able to run a variety of AIX, Linux and i5/OS guest images.The "Live Partition Mobility" feature allows you to easily move guest images from one system to another, while they are running, just like VMotion for x86 machines.
And while we are on the topic of x86, PowerVM is also able to represent a Linux-x86 emulation base to run x86-compiled applications. While many Linux applications could be re-complied from source code for the POWER architecture "as is", others required perhaps 1-2 percent modification to port them over, and that was too much for some software development houses. Now, we can run most x86-compiled Linux application binaries in their original form on POWER architecture servers.
BladeCenter JS22 Express
The POWER6-based [JS22 Express blade] can run i5/OS, taking advantage of PowerVM and VIOS to access all of the BladeCenterresources. The BladeCenter lets you mix and match POWER and x86-based blades in the same chassis, providing theultimate in flexibility.
This week I'm in beautiful Guadalajara, Mexico teaching at our[System Storage Portfolio Top Gun class].We have all of our various routes-to-market represented here, including our direct sales force, our technicalteams, our online IBM.COM website sales, as well as IBM Business Partners.Everyone is excited over last week's IBM announcement of [4Q07 and full year 2007 results], which includesdouble-digit growth in our IBM System Storage business, led by sales of our DS8000, SAN Volume Controller and Tapesystems. Obviously, as an IBM employee and stockholder, I am biased, so instead I thought I would provide someexcerpts from other bloggers and journalists.
But what was striking in the company’s conference call on Thursday afternoon was the unhedged optimism in its outlook for 2008, given the strong whiff of recession fear elsewhere.
The questions from Wall Street analysts in the conference call had a common theme. Why are you so comfortable about the 2008 outlook? Now, that might just be professional churlishness, since so many of them have been so wrong recently about I.B.M. Wall Street had understandably thought, for example, that I.B.M.’s sales to financial services companies — the technology giant’s largest single customer category — would suffer in the fourth quarter, given the way banks have been battered by the mortgage credit crunch.
But Mr. Loughridge said that revenue from financial services customers rose 11 percent in the fourth quarter, to $8 billion. The United States, he noted, accounts for only 25 percent of I.B.M.’s financial services business.
The other thing that seems apparent is how much I.B.M.’s long-term strategy of moving up to higher-profit businesses and increasingly relying on services and software is working. Its huge services business grew 17 percent to $14.9 billion in the quarter. After the currency benefit, the gain was 10 percent, but still impressive. Software sales rose 12 percent to $6.3 billion.
Looking at IBM's business segments, it can be seen that they offer far more coverage of the technology space that those of the typical tech company:
IBM is just so big and diversified that there is little comparison between it and most other tech companies. IBM is a member of an elite group of companies like Cisco Systems (CSCO), Microsoft (MSFT), Oracle (ORCL) or Hewlett-Packard (HPQ).
IBM's wide international coverage and deep technological capabilities dwarf those of most tech companies. Not only do they have sales organizations worldwide but they have developers, consultants, R&D workers and supply chain workers in each geographic region. Their product mix runs from custom software to packaged enterprise software, hardware (mainframes and servers), semiconductors, databases, middleware technology, etc., etc. There are few tech companies that even attempt to support that many kinds and variations of products.
As color on the fourth quarter earnings announcement, there are a couple of observations that I would like to make. The first one speaks to IBM's international prowess. The company indicated that growth in the Americas was only 5%. International sales were a primary driver of IBM's good results. As an insight on the difference between IBM and most other tech companies, it is clear that nowadays, a tech company that isn't adept at selling internationally is going to be in trouble.
Terrific performance in a terrific year - no doubt a result of its strong global model. IBM operates in 170 countries, with about 65% of its employees outside US and about 30% in Asia Pacific. For fiscal 2007, revenues from Americas grew 4% to $41.1 billion (42% of total revenue), [EMEA] grew 14% to $34.7 billion (35%of total revenue), and Asia-Pacific grew by 11% to $19.5 billion (19.7% of total revenue). IBM sees growth prospects not just in [BRIC] but also countries like Malaysia, Poland, South Africa, Peru, and Singapore.
Thus far 2008–all two weeks of it–hasn’t been a pretty for the tech industry. Worries about the economy prevail. And even companies that had relatively good things to say like Intel get clobbered. It’s ugly out there–unless you’re IBM.
I am sure there will be more write-ups and analyses on this over the next coming weeks, and others will probably waituntil more tech companies announce their results for comparison.
Yesterday's announcement that IBM had acquired XIV to offer storage for Web 2.0 applicationsprompted a lot of discussion in both the media and the blogosphere. Several indicated thatit was about time that one of the major vendors stepped forward to provide this, and it madesense that IBM, the leader in storage hardware marketshare, would be the first. Others were perhaps confused on what is unique with Web 2.0 applications. What has changed?
I'll use this graphic to help explain how we have transitioned through three eras of storage.
The first era: Server-centric
In the 1950s, IBM introduced both tape and disk systems into a very server-centric environment.Dumb terminals and dumb storage devices were managed entirely by the brains inside the server.These machines were designed for Online Transaction Processing (OLTP), everywhere from bookingflights on airlines to handling financial transfers.
The second era: Network-centric
In the 1980s and 1990s, dumb terminals were replaced with smarter workstations and personalcomputers; and dumb storage were replaced with smarter storage controllers. Local Area Networks (LANs)and Storage Area Networks (SANs) allowed more cooperative processing between users, servers andstorage. However, servers maintained their role as gatekeepers. Users had to go through aspecific server or server cluster to access the storage they had access to. These servers continuedtheir role in OLTP, but also manage informational databases, file sharing and web serving.
The third era: Information-centric
Today, we are entering a third era. Servers are no longer the gatekeepers. Smart workstationsand personal computers are now supplemented with even more intelligent handheld devices, Blackberryand iPhones, for example. Storage is more intelligent too, with some being able to offer file sharingand web serving directly, without the need of an intervening server. The roles of servers have changed,from gatekeepers, to ones that focuses on crunching the numbers, and making information presentableand useful.
Here is where Web 2.0 applications, digital media and archives fits in. These are focused on unstructured data that don't require relational database management systems. So long as the useris authorized, subscribed and/or has made the appropriate payment, she can access the information. With the appropriate schemes in place, information can now be mashed-up in a variety of ways, combined with other information that can render insights and help drive new innovations.
Of course, we will still have databases and online transaction processing to book our flights andtransfer our funds, but this new era brings in new requirements for information storage, and newarchitectures that help optimize this new approach.
It's official! My "blook" Inside System Storage - Volume I is now available.
This blog-based book, or “blook”, comprises the first twelve months of posts from this Inside System Storage blog,165 posts in all, from September 1, 2006 to August 31, 2007. Foreword by Jennifer Jones. 404 pages.
IT storage and storage networking concepts
IBM strategy, hardware, software and services
Disk systems, Tape systems, and storage networking
Storage and infrastructure management software
Second Life, Facebook, and other Web 2.0 platforms
IBM’s many alliances, partners and competitors
How IT storage impacts society and industry
You can choose between hardcover (with dust jacket) or paperback versions:
This is not the first time I've been published. I have authored articles for storage industry magazines, written large sections of IBM publications and manuals, submitted presentations and whitepapers to conference proceedings, and even had a short story published with illustrations by the famous cartoon writer[Ted Rall].
But I can say this is my first blook, and as far as I can tell, the first blook from IBM's many bloggers on DeveloperWorks, and the first blook about the IT storage industry.I got the idea when I saw [Lulu Publishing] run a "blook" contest. The Lulu Blooker Prize is the world's first literary prize devoted to "blooks"--books based on blogs or other websites, including webcomics. The [Lulu Blooker Blog] lists past year winners. Lulu is one of the new innovative "print-on-demand" publishers. Rather than printing hundredsor thousands of books in advance, as other publishers require, Lulu doesn't print them until you order them.
I considered cute titles like A Year of Living Dangerously, orAn Engineer in Marketing La-La land, or Around the World in 165 Posts, but settled on a title that matched closely the name of the blog.
In addition to my blog posts, I provide additional insights and behind-the-scenes commentary. If you go to the Luluwebsite above, you can preview an entire chapter in its entirety before purchase. I have added a hefty 56-page Glossary of Acronyms and Terms (GOAT) with over 900 storage-related terms defined, which also doubles as an index back to the post (or posts) that use or further explain each term.
So who might be interested in this blook?
Business Partners and Sales Reps looking to give a nice gift to their best clients and colleagues
Managers looking to reward early-tenure employees and retain the best talent
IT specialists and technicians wanting a marketing perspective of the storage industry
Mentors interested in providing motivation and encouragement to their proteges
Educators looking to provide books for their classroom or library collection
Authors looking to write a blook themselves, to see how to format and structure a finished product
Marketing personnel that want to better understand Web 2.0, Second Life and social networking
Analysts and journalists looking to understand how storage impacts the IT industry, and society overall
College graduates and others interested in a career as a storage administrator
And yes, according to Lulu, if you order soon, you can have it by December 25.