This section contains one per device.
Offsets | Name | Length | Format | Description | |
---|---|---|---|---|---|
0 | 0 | R799NUM | 2 | packed | Device number. |
2 | 2 | R799LCU | 2 | binary | Logical control unit number X'00' to X'FF'. |
4 | 4 | 1 | Reserved. | ||
5 | 5 | R799CNF | 1 | binary | Device flags
|
6 | 6 | R799SER | 6 | EBCDIC | Volume serial number of the volume mounted on this device. |
12 | C | R799TYP | 4 | binary | Device type. |
16 | 10 | R799NUX | 4 | binary | Number of base and alias devices for a parallel access volume (PAV). This field is 1 for a non-PAV device. For HyperPAV base devices (bit 6 of R799CNX is set), this is the accumulated number of HyperPAV aliases. |
20 | 14 | R799SSC | 4 | binary | Start subchannel (SSCH) count. |
24 | 18 | R799MEC | 4 | binary | Measurement event count; number of SSCH instructions for which connect, pending, and active times were stored. |
28 | 1C | R799CNN | 4 | binary | Device connect time. |
32 | 20 | R799PEN | 4 | binary | Function pending time. |
36 | 24 | R799ATV | 4 | binary | Function active time. |
40 | 28 | R799DIS | 4 | binary | Device disconnect time. |
44 | 2C | R799QUE | 4 | binary | Number of requests queued in IOS for this device. |
48 | 30 | R799UTL | 4 | binary | Number of samples when the device was reserved but an SSCH had not been issued to the device. |
52 | 34 | R799RSV | 4 | binary | Number of samples taken during the measurement interval that indicated that the device was reserved. |
56 | 38 | 4 | Reserved. | ||
60 | 3C | R799ALC | 4 | binary | Number of samples taken during the measurement interval that indicated that the device was allocated. |
64 | 40 | R799DVB | 4 | binary | Device busy delay time. |
68 | 44 | R799CUB | 4 | binary | Shows control unit busy delay time if bit 4 in R799CNX is set off. |
72 | 48 | R799ICT | 2 | binary | Incorrect sample count. |
74 | 4A | R799CNX | 1 | binary | Device flag extensions.
|
75 | 4B | 1 | Reserved. | ||
76 | 4C | R799SGN | 8 | EBCDIC | Storage group name. |
84 | 54 | R799NDA | 4 | binary | Total number of allocations in effect for the device. |
88 | 58 | R799DPB | 4 | binary | Shows the amount of time during the measurement interval that I/O requests to a device were delayed because a director port was busy if bit 4 of R799CNX is set off. |
92 | 5C | R799CMR | 4 | unsigned binary | Shows initial command response time in units of 128 microseconds if bit 5 of R799CNX is set on. |
96 | 60 | R799PCT | 4 | binary | Number of unsuccessful PAV samples. |
100 | 64 | R799PSM | 4 | binary | Number of successful PAV samples. |
104 | 68 | R799IDT | 4 | binary | Interrupt delay time in units of 128 microseconds. This field is zero if not supported by the hardware. |
108 | 6C | R799CUQ | 4 | binary | Control Unit Queuing Time. |
112 | 70 | R799CN2 | 1 | binary | Device flag extension 2
|
113 | 71 | R799SCS | 1 | binary | Subchannel set ID. |
114 | 72 | R799NM2 | 2 | binary | Device number (same as R799NUM). |