The DASDID control statements identify the devices in
your installation and the paths to the processors they work with.
You
need DASDID control statements to provide EREP with physical
identifiers for the DASD in your installation that do
not provide their own physical IDs. See Direct-Access Storage Devices (DASD) for
these devices.
EREP uses these physical identifiers to
determine the probable failing unit (PFU) for the system exception
report series.
The DASDID statements define the different paths
from processors to devices in much the same way as do SHARE statements:
- You can use the DASDID statements to take the place of SHARE statements
for the DASD subsystem exception reports.
- You can include the SHARE statements for DASD when you run the
system exception report series, but EREP ignores them and uses the
DASDID information instead.
Set up the DASDID statements, before you request the
system exception report series. See Setting up DASDID Controls for
detailed directions on preparing DASDID controls.
Indicates
The paths from a processor through
channels, storage control units and controllers to each drive.
Syntax
DASDID
statement formats differ depending on whether the processor is running
in 370 or 370XA mode.
The syntax of the
370 DASDID control
statement is:
>>-DASDID CPU=--nnnnnn--,--CH=--xx--,--SCU=--ss--,-------------->
.-,----------.
V |
>----STR=--ccuu-+----------------------------------------------><
- nnnnnn
- Is a six-digit decimal CPU serial number.
- xx
- Is a two-digit hexadecimal number identifying the channel (CH)
between this CPU and the storage control unit.
- ss
- Is the physical identifier of the storage control unit (SCU).
Each SCU must have a unique ID number.
- ccuu
- Is a four-digit hexadecimal value representing the controller
and unit address for each DASD string (STR). The DASD string is the
set of eight unit addresses assigned to one controller (or pair of
controllers):
- cc
- Is the number you assign, in the range of 01–FE, to each controller.
Each controller must have a unique ID number; however, controllers
with string switch and 3350s with alternate controllers should have
only one ID number.
- uu
- Is the last two digits from the lowest address on the string.
The second digit should be zero or eight.
The format of the
370XA DASDID control statement is:
>>-DASDID CPU=--Xnnnnn--,--CHP=--xx--,--SCU=--ss--,------------->
.-,------------.
V |
>----STR=--ccdddd-+--------------------------------------------><
- Xnnnnn
- Is a five-digit hexadecimal CPU serial number preceded by an X in
the central processor (CP) identifier position.
- xx
- Is the two-digit hexadecimal number identifying the channel path
identifier (CHP) between this CPU and the storage control unit.
- ss
- Is the physical identifier of the storage control unit (SCU).
Each SCU must have a unique ID number.
- ccdddd
- Is a five- or six-digit hexadecimal value representing the controller
device number for each DASD string (STR). The DASD string is the set
of eight device numbers assigned to one controller (or pair of controllers):
- cc
- Is the number you assign, in the range of 01–FE, to each controller.
Each controller must have a unique ID number; however, controllers
with string switches and 3350s with alternate controllers should have
only one ID number.
- dddd
- Is the lowest device number on the string.
Defaults
None.
If
you omit DASDID statements, those DASD that do not provide their own
physical IDs are identified on the reports only by device type.
Coding
- DASDID must be the first word in the statement, followed by one
blank and the CPU= keyword with its associated value.
- The keywords on this statement are positional and must be separated
by commas.
Notes
The
combined number of distinct CPUs specified on all of your control
statements cannot exceed 256.
Examples
The
following sections give you examples:
- Setting up DASDID Controls describes how to set up
DASDID control statements for your DASD subsystem.
- Checking Your DASDID Statements describes how to use the
EREP messages file (TOURIST output) to make sure that your DASDID
statements match your DASD subsystem configuration.
- DASDID Configuration Chart Notes describes how to use
the notes that may accompany the DASDID configuration chart and their
meanings.