>>-DEVSERV--QPAVS--,--------------------------------------------> >--+-device--+----+--+-+-------+--+------+--+------+-+-+------->< | '-,1-' | '-,HPAV-' '-,DCE-' '-,UCB-' | | | '-,VOLUME-----------------------' | +-device--+------+--,UNBOX--------------------------+ | '-,num-' | '-SSID=ssid-+-------------------+-------------------' '-,device--+------+-' '-,num-'
Figure 1 shows the display content when you issue the DEVSERV QPAVS command with parameters other than DCE and UCB. If you specify the DCE or UCB parameter (or both), additional DCE or UCB information (or both) is displayed for the device. This additional information is formatted the same way as the output resulting from the QDASD parameter.
-----------------------------------------------------
--- DS QP Display Content ---
-----------------------------------------------------
IEE459I (time) DEVSERV QPAVS
Host Subsystem
Configuration Configuration
------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR TYPE
----- -- ---- ------ ---- ---- --------
sdddd aa BASE INV-ALIAS ssss uu BASE
ALIAS-bbbb NOT-BASE ALIAS-bb
NON-PAV NOT-ALIAS NC
sdddd bb ALIAS UNBOUND ssss uu ALIAS-aa
sdddd bb ALIAS-bbbb ssss uu ALIAS-aa
sdddd aa BASE-H ssss uu BASE
sdddd bb ALIAS-H ssss uu ALIAS-H
UNLISTED DEVICES AND REASON CODES X
sdddd(rc) sdddd(rc) sdddd(rc) ...
The following are examples of DEVSERV QPAVS output.
Figure 2 shows the PAV status for the device at the starting address D123 and the next 2 addresses.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- -------
0D123 23 NON-PAV 0101 23 BASE
0D124 24 NON-PAV 0101 24 BASE
0D125 25 NON-PAV 0101 25 BASE
**** 3 DEVICE(S) MET THE SELECTION CRITERIA
Figure 3 shows the PAV status for the alias device at the address D2FF, its base, and other associated alias devices of the logical volume.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- --------
0D222 22 BASE 0102 22 BASE
0D2FE FE ALIAS-D222 0102 FE ALIAS-22
0D2FF FF ALIAS-D222 0102 FF ALIAS-22
**** 3 DEVICE(S) MET THE SELECTION CRITERIA
Figure 4 shows the PAV status for the base device at the address D222 and its alias volumes without the subchannel set support installed.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- --------
0D222 22 BASE 0102 22 BASE
0D2FE FE ALIAS-D222 0102 FE ALIAS-22
0D2FF FF ALIAS-D222 0102 FF ALIAS-22
**** 3 DEVICE(S) MET THE SELECTION CRITERIA
Figure 5 shows that you can "unbox" a boxed alias device at the address D6FF.
IEE459I 08.20.32 DEVSERV QPAVS 591
THE DEVSERV QPAV UNBOX COMMAND HAS BEEN SUCCESSFULLY UNBOXED 1
IEE459I 08.20.32 DEVSERV QPAVS 591
THE DEVSERV QPAV UNBOX COMMAND HAS BEEN EXECUTED WITH
RETURN CODE = xx, REASON CODE = yy 2
IEE459I 10.04.23 DEVSERV QPAVS 699
D6FF IS NOT AN UNBOUND PAV-ALIAS DEVICE. 3
THE DEVSERV QPAV UNBOX COMMAND IS NOT EXECUTED
1 You receive this message if the return code from DEVSERV QPAVS UNBOX is zero.
2 You receive this message if the return code from DEVSERV QPAVS UNBOX is nonzero.
3 You may also receive this message with the explanation: "nnnn-IS NOT IN BOX STATE."
Figure 6 describes the status of an unbound alias and the display of its associated UCB control blocks.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- ---------
UCB AT V01ED2AA8
0088FF04D5EF0000 0000000008E4C3C2 3010200E00ED2A81 0000000000000000
0000000000100000 0000000000000000 0000000000000000
UCB PREFIX AT V01FF4208
000C804000000000 000000000001004E 289C1253C00080C0 14F4FFFFFFFFFFFF
0148000000000001
UCB COMMON EXTENSION AT V01ED2A80
00000900182A0000 01FF420800000000 0000000000FCD3D8 01ECA90000000000
**** UNLISTED DEVICE(S) AND REASON CODES:
0D5EF(0A)
**** (0A) - DEVICE IS AN UNBOUND PAV-ALIAS
Figure 7 shows the PAV status of the devices that have the same SSID value.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- --------
0D400 00 NON-PAV 1401 00 BASE
....
0D422 22 BASE 1401 22 BASE
....
0D4FF FF ALIAS-D422 1401 FF ALIAS-22
**** 256 DEVICE(S) MET THE SELECTION CRITERIA
Figure 8 shows the status of NOT-BASE when the address D345 is defined as a PAV-base in the HCD, but not in the ESS logical subsystem.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- --------
0D345 45 BASE NOT-BASE 0103 45 ALIAS-00
**** 1 DEVICE(S) MET THE SELECTION CRITERIA
Figure 9 shows the status of NOT-ALIAS when the address D621 is defined as a PAV-alias in the HCD, but not in the ESS logical subsystem.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- ---------
0D621 21 ALIAS-D600 NOT-ALIAS 0106 21 BASE
**** 1 DEVICE(S) MET THE SELECTION CRITERIA
Figure 10 shows the status of INV-ALIAS when the alias address D6F4 for the base volume in the HCD does not match its base address in the ESS logical subsystem.
IEE459I 08.20.32 DEVSERV QPAVS 591
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- --------
0D6F4 F4 ALIAS-D600 INV-ALIAS 0106 F4 ALIAS-06
**** 1 DEVICE(S) MET THE SELECTION CRITERIA
Figure 11 shows the status of NOT-NPAV for the device at the address F60. The device is defined as a NON-PAV device in the HCD, but is given an alias in the ESS logical subsystem.
IEE459I 13.20.12 DEVSERV QPAVS 368
Host Subsystem
Configuration Configuration
-------------- --------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ------ ------ ---- ---- --------
00F60 F0 NON-PAV NOT-NPAV 0101 F0 ALIAS-03
Figure 12 shows the display content when you issue the DEVSERV QPAVS command with the HPAV parameter, with the target of the command being a HyperPAV alias device number.
09.07.08 SYSTEM1 ds qpavs,e27f,hpav
09.07.08 SYSTEM1 IEE459I 09.07.08 DEVSERV QPAVS 472
HOST SUBSYSTEM
CONFIGURATION CONFIGURATION
--------------- ---------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- ----------
0E27E ALIAS-H
0E27F ALIAS-H
**** 2 DEVICE(S) IN HYPERPAV ALIAS POOL
Figure 13 shows the display content when you issue the DEVSERV QPAVS command with the HPAV parameter, with the target of the command being a HYPERPAV base device number.
09.07.08 SYSTEM1 ds qpavs,e200,hpav
09.07.08 SYSTEM1 IEE459I 09.07.08 DEVSERV QPAVS 472
HOST SUBSYSTEM
CONFIGURATION CONFIGURATION
--------------- ---------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- ----------
0E200 00 BASE-H 3205 00 BASE
0E27E ALIAS-H
0E27F ALIAS-H
**** 3 DEVICE(S) IN HYPERPAV ALIAS POOL
Figure 14 shows the display content when you issue the DEVSERV QPAVS command with the VOLUME parameter, with the target of the command being a HYPERPAV alias device number.
09.07.08 SYSTEM1 ds qpavs,e27f,volume
09.07.08 SYSTEM1 IEE459I 09.07.08 DEVSERV QPAVS 472
HOST SUBSYSTEM
CONFIGURATION CONFIGURATION
--------------- ---------------------
UNIT UNIT UA
NUM. UA TYPE STATUS SSID ADDR. TYPE
----- -- ---- ------ ---- ---- ----------
**** UNLISTED DEVICE(S) AND REASON CODES :
0E27F(0E)
**** (0E) - DEVICE IS A HYPERPAV ALIAS