DEVINFO: Unable to complete request with the return area provided.
Return code: 4.
0002
DEVINFO: Some of the returned entries have nonzero response codes.
Return code: 8.
0003
DEVINFO: Caller provided a bad parameter in the parameter list.
Return code: 12.
0004
DEVINFO: Internal error was encountered. Return code: 16.
0005
Unexpected return code (DGTCDSAP) or (DGTCVAAP) came from routines
called by the data set or volume application component.
0006
Errors occurred during previous processing. Check the previous
log entries for detailed error information.
0007
List source is invalid. It should be either VTOC or CATALOG.
0008
TRKCALC macro failed. Return code: 4.
0009
Automatic data area is in use. An ISMF common service routine
was entered and the frozen storage for its automatic data area was
already in use.
0010
Selection criteria is invalid and will produce an empty list.
0011
Filter criteria is invalid and will produce an empty list.
0012
Prolog failure: Storage for the invoking module's automatic data
area was not obtained.
0013
Epilog failure: Invoking module's automatic data area could not
be freed.
0014
Panel number is invalid. A valid panel number is 1, 2, or 3.
0015
Invalid command is not detected by the command check routine.
0016
Convert Utility: Target data length must be 4 bytes or less when
converting a character string to its fixed binary representation.
0017
Convert Utility: Invalid character was found in the data to be
converted. Data conversion could not take place. In some cases, imbedded
blanks are invalid.
0018
Desired DAB was not found in the DAB list.
0019
Data to be converted contained all blanks and could not be converted.
0020
TBADD: Severe table error. Return code: 20.
0021
TBADD: Table is not open. Return code: 12.
0022
TBADD: Numeric convert error. Return code: 16.
0023
TBCREATE: Severe table error. Return code: 20.
0024
TBCREATE: Table is in use and ENQ failed. Return code: 12.
0025
TBCREATE: Table already exists. REPLACE was not specified. Return
code: 8.
0026
TBDELETE: Severe table error. Return code: 20.
0027
TBDELETE: Table is not open. Return code: 12.
0028
TBDELETE: CRP was at top (0) and remains at top. Return code:
8.
0029
TBEND: Severe table error. Return code: 20.
0030
TBEND: Table is not open. Return code: 12.
0031
TBGET: Severe table error. Return code: 20.
0032
TBGET: Table is not open. Return code: 12.
0033
TBGET: Variable value was truncated, or insufficient space was
provided to return all extension variable names. Return code:16.
0034
TBGET: CRP was at top (0) and remains at top. Return code: 8.
0035
Convert utility: Source data length must be 2 bytes when converting
data set organization from the DSCB format to the list format.
0036
TBSCAN: Severe table error. Return code: 20.
0037
TBSCAN: Table is not open. Return code: 12.
0038
TBSCAN: Row does not exist. No match was found and CRP is set
to top (0). Return code: 8.
0039
TBSCAN: Variable value was truncated, or insufficient space was
provided to return all extension variable names. Return code: 16.
0040
Convert utility: Target length must be at least 3 bytes to hold
the converted DSORG value.
0041
Convert utility: Source data length must be 1 byte when converting
allocation unit from the DSCB format to the ISMF list format.
0042
Convert utility: Target data length must be at least 3 bytes to
hold the converted allocation unit.
0043
Convert utility: Allocation unit could not be determined from
the input.
0044
Convert utility: Source data length for converting record format
is invalid. It must be 1 byte.
0045
Convert utility: Target data length must be at least 5 bytes to
hold the converted record format.
0046
Convert utility: Record format could not be determined from the
input.
0047
Convert utility: Source data length must be 1 byte when converting
the allocation unit from the catalog format to the ISMF list format.
0048
Convert utility: Source data length must be at least 3 bytes to
convert the allocation unit into the corresponding bit mapping.
0049
Convert utility: Target data length must be at least 1 byte to
convert the allocation unit into the corresponding bit mapping.
0050
Convert utility: Source data length must be 4 bytes when converting
device type from the UCB to the ISMF list format.
0051
RETRY routine is in control.
0052
No storage was allocated. Return code: 4.
0053
Real storage is not available to back request. Return code: 8.
0054
Unexpected error occurred while processing ESTAE. Return code:
16.
0055
ESTAE macro was unable to obtain storage for an SCB. Return code:
20.
0056
Level of DFDSS was not returned by DGTFMDO3.
0057
Level of DFHSM was not returned by DGTFMDO4.
0058
Not all storage is freed. Return code: 4.
0059
Delete request was not issued. Return code: 4.
0060
Level of DFDSS could not be determined by the DFDSS ADRMCLVL macro. X'04' was
passed back in the high order byte in register 1 by the ADRMCLVL macro,
indicating that it was unable to determine the current level of DFDSS.
0061
LOAD macro failed. Control was given to the error routine specified
in the LOAD macro invocation. Return code: 4.
0062
ISPF select failed. Specified panel could not be found. Return
code: 12.
0063
Unable to build the error table (ERTB).
0064
No exits exist for this TCB. Return code: 12.
0065
ISPF SETMSG failed. Panel message not found or syntax is invalid.
Return code: 12.
0066
ISPF SETMSG service failed. Severe error occurred in processing
ISPF SETMSG service. Return code: 20.
0067
ISPF log failed. Log message invalid or not found. Return code:
12.
0068
ISPF log failed. Severe error in ISPF log service. Return code:
20.
0069
Unable to build the inter-module trace table (IMTT).
0070
Unable to build the load list block (LLBL).
0071
Unable to build the storage control table (SCT).
0072
Unable to build the service routine vector table (SRVT).
0073
Unable to build the trace point trace table (TPTT).
0074
ISPF select failed. Truncation error in storing the ZCMD or ZSEL
variable. Return code: 16.
0075
ISPF select failed. Severe error. Return code: 20.
0076
Invalid return code received from ISPF select.
0077
Invalid logging type was passed to the ISMF log utility.
0078
Convert utility: Target data length must be at least 7 bytes when
converting the device type from the UCB into the ISMF list format.
0079
Convert utility: Device type could not be determined from the
data.
0080
Convert utility: Source data length must be 7 bytes when converting
the device type from the ISMF list form to the UCB form.
0081
Convert utility: Target data length must be 4 bytes when converting
the device type from the ISMF list form to the UCB form.
0082
Convert utility: Source data length must be 1 byte when converting
the DSCB change indicator bit into an EBCDIC character string .
0083
Convert utility: Target data length must be at least 3 bytes when
converting the DSCB change indicator bit into an EBCDIC character
string.
0084
Convert utility: Source data length for converting the option
code field of a DSCB (DS1OPTCD) into a character string must be 1
byte.
0085
Convert utility: Target data length for converting the option
code field of a DSCB (DS1OPTCD) into a character string must be at
least 1 byte.
0086
Convert utility: Source data length must be 4 bytes when converting
a fullword fixed binary number representing bytes into the corresponding
kilobyte representation.
0087
Convert utility: Source data length must be 3 bytes when converting
a fixed binary date into its character string representation.
0088
Convert utility: Target data length must be at least 8 bytes to
hold a converted date in its character string format, 'YY/MM/DD'.
0089
Convert utility: Specified source index is invalid.
0090
Convert utility: Specified target index is invalid.
0091
Convert utility: Invalid year was found when performing a date
conversion.
0092
Convert utility: Invalid month was found when performing a date
conversion.
0093
Convert utility: Invalid day was found when performing a date
conversion.
0094
Convert utility: Source data length must be 8 bytes when converting
a date in the character string format, 'YY/MM/DD', into a fixed packed
decimal format, 'YYDDDS', where S is the sign digit.
0095
Convert utility: Target data length must be 3 bytes when converting
a date in the character string format, 'YY/MM/DD', into a fixed packed
decimal format, 'YYDDDS', where S is the sign digit.
0096
Convert utility: Source data length can be a maximum of 8 bytes
when converting a character string to its fixed binary representation.
0097
Convert utility: Source data length must be 3 bytes when converting
a date in packed decimal format to its character string representation
of 'YY/MM/DD'.
0098
Link SVC failed.
0099
Convert utility: Undetermined data set organization.
0100
Convert utility: Unable to load the conversion translate table
(CTTB).
0101
Invalid scroll amount, the valid format is: P (page); H (half);
D (data); M (maximum); C (cursor); NNNN (a number from 1 to 9999).
0102
Command not found in the application command table.
0103
One or more commands not found in the application command table.
0104
Command processor parameter list pointer=0.
0105
Application command table pointer=0.
0106
Command table anchor block pointer=0.
0107
Array name pointer=0.
0108
Format name pointer=0.
0109
Command line pointer=0.
0110
Unexpected error occurred in external routine.
0111
Command line length=0.
0112
Command length is invalid.
0113
Command specified is in disable status in the application command
table.
0114
Panel type is invalid. Function only supports a list panel.
0115
Command/line operator control blocks chain is not 0 before storage
is freed.
0116
Application ID is invalid.
0117
No application table is being loaded.
0118
When the hide pending mode is on, no list command is allowed.
0119
Termination type is invalid.
0120
Command table initialization failed.
0121
Command table entry count=0.
0122
Error occurred while command processor was trying to process the
error routine.
0123
CTABCLCB is not equal to CPPLCLCB.
0124
Nonzero return code came from ISPF control service.
0125
Reserved for command processor.
0126
Invalid storage size passed to the get-memory routine.
0127
Invalid storage ID passed to the get-memory routine.
0128
Unexpected column name found in DAB. DABs may be out of order.
0129
Invalid cursor control block chained from the command processor
parameter list (CPPL).
0130
Invoker's APID does not match current CTABAPID.
0131
Invoker's APID was not found in the CTAB chain.
0132
Two CTABs have duplicate APIDs that match the invoker's APID.
0133
Nonzero return code was passed back from the invoked CLIST.
0134
Specified CLIST name was too long. CLIST name must be 1 to 8 characters
long (optionally preceded by '%').
0135
ISPF/PDF edit failed. Specified member was not found. Return code:
14.
0136
ISPF/PDF edit failed. Data was zero length (empty sequential data
set or zero length member of a partitioned data set). Return code:
12.
0137
Nonzero return code was passed back from the specified CLIST.
0138
Invalid system completion code was passed in the retry work area.
0139
Incorrect number of parameters was specified.
0140
Member name specified is too long.
0141
TBSAVE: Table is not open. Return code: 12.
0142
TBSAVE: Table output library is not open. Return code: 16.
0143
TBSAVE: Severe error. Return code: 20.
0144
TBSAVE: Unexpected return code.
0188
Convert utility: The target data length must be at least 10 bytes
to hold a converted date in its character string format YYYY/MM/DD.
0189
Convert utility: An invalid century and year in the format YYYY
was found when performing a date conversion.
0190
Convert utility: An invalid century was found when performing
a date conversion.
0191
Convert utility: An invalid century was found when performing
a date conversion.
0197
Convert utility: The source data length must be 4 bytes when converting
a date in packed decimal format to its character string representation
of YYYY/MM/DD.
0200
Line operator anchor block pointer=0.
0201
List command and line operator conflict.
0202
Line operator was not found in the application line operator table.
0203
Entry in the line operator field is greater than 10 characters.
0204
Record format is not F or FB.
0205
Program failed because of a failure in the invoked external routine.
Refer to the failed external routine problem determination area.
0206
Application line operator table pointer=0.
0207
Line operator processor work area pointer=0.
0208
Invalid return code from ISPF/PDF browse service.
0209
Duplicate table entry found while loading the table entries. Only
one of the duplicates is loaded.
0210
Line operator initialization failed.
0211
Line operator processor failed due to multiple errors.
0212
Operator line length is invalid.
0213
Line operator field length=0.
0214
DGTFLPP3 rewrite the saved ERTB entry so that the error message
can be displayed on screen.
0215
TOTLINES field is zero.
0216
Line operator does not have 'H' in column one but is asking DGTFLPP2
to check whether it is a hide line operator.
0217
LPP2ALL and LPP2HI flags are off. No checking or verification
is done by this program.
0218
Return code from DGTEFOFI is zero, but no value returned to entry
number filed. Invalid combination of return code and value returned.
0219
Caller's ID is invalid. Valid IDs are 'CT', 'LP'.
0220
Invalid value in LOOPCNT.
0224
CSRFLAG value is not 1 and not -1. It is an invalid and unexpected
value.
0225
Invalid return code came from ISPF/PDF edit.
0226
ISPF control service failed.
0227
Invalid value specified.
0230
No invocation is set for the hide line operator. LPPLHIDE is off.
0231
Hide amount is not numeric.
0232
LAI address (LPPLLAIA) is 0.
0233
Line operator does not have 'H' at column one and is not a hide
line operator.
0234
No entry in the list area image to be processed. LPPLLAIT is less
than 1.
0235
Hide range exceeds allowable maximum of 99999.
0236
LPPLENT is less than 1.
0237
Hide amount overlaps another pending line operator.
0238
HIDEAMT=0.
0239
HIDEAMT is not in the allowable range, 1 to 99999.
0240
LPPLENT is greater than LPPLLAIT.
0241
CSRFLAG is off when there is entry in the list area image.
0242
LPPLROWA=0.
0243
LPCBENO=0.
0244
Entry number in LPAB (LPCBENO) is greater than the size of the
LAI.
0245
LPCB address is 0.
0246
Invalid value returned from format service. Valid values are 'Y'
or 'N'. NAE of the format service can be found in the ISPF log.
0250
Invalid FIND parameter: ISMF user did not enter a column tag.
0251
Invalid command parameter: Only one parameter is accepted for
this command.
0254
Invalid cursor position: Cursor is placed between the data columns
in the list area. This is invalid for scrolling with the cursor position.
0255
Value of the scroll variable is invalid.
0256
Area name from LPCB is invalid.
0301
Format service anchor block (FSAB) does not exist. Pointer to
FSAB in the global data repository block (GDRB) is 0.
0302
Format anchor block (FAB) was not found. No match of format name
and array name exists in a FAB.
0303
Control block structure with the same format and array name already
exists.
0304
Variables of list area (VLA) are invalid. VLA may be incomplete.
0305
Input parameter number of entries (ENTNUM) is invalid. Value is
greater than the total number of entries in the LAI or is a negative
number.
0306
Input parameter multiline (MULLINE) is invalid. Value of MULLINE
is 2, but this is a single line entry.
0307
Input parameter number of entries in the input array (INPENT)
is invalid. Number of entries specified in INPENT is not equal to
the number of entries actually in the LAI.
0308
Data column descriptor (DCD) for corresponding data attribute
block (DAB) does not exist.
0309
Input parameter area is invalid. Area name is not one of the following:
input, object, data, or command.
0310
Input parameter offset is invalid. Offset is out of range.
0311
Data attribute block pointer (DABLPTR) does not point to a valid
DABL.
0312
FDBLEFT or FDBRITE in the format data block (FDB) is invalid.
Value is less than 0 or greater than the number of displayable data
columns.
0314
Data column is too wide to be put in the data area.
0315
Invalid input parameter ADDRFABOR DCDNO in module DGTFFOX1.
0316
ISPF/PDF browse failed. Zero length data (empty sequential data
set or 0 length member of a partitioned data set). Return code: 12.
0317
ISPF/PDF browse failed. Specified member not found. Return code:
14.
0318
Input parameter column name list (COLLIST) is invalid. At least
one of the column names in the COLLIST was not found.
0319
Column tag specified by the user is invalid.
0320
Column tag specified is not displayed.
0321
Entry identified by the ROWID is not displayed.
0322
ISPF/PDF browse failed. No members were in library when the member
list was requested. Return code: 16.
0323
Cursor is not placed in a field of the LIST panel.
0324
Cursor is placed in one of the fields: fixed area (entry statement,
data column statement) or warning.
0325
Cursor is placed in a gap between 2 data columns.
0326
Cursor is placed in a field of the LIST panel, but it is not one
of the following: command line, entry statement, data column statement,
warning, column headings, tags, or LAI.
0327
ISPF/PDF browse failed. Severe error, unable to continue. Return
code: 20.
0328
ISPF/PDF edit failed. No members were in the library when member
list was requested. Return code: 16.
0329
Value of FDBVSIZE (the vertical size of the list area of the current
display with factor of split screen considered) in module DGTFFOF1
is invalid.
0330
Value in the extension variable from the variables of list area
(VLA) is invalid.
0331
Value of MAXL (length of variables NAME1 and NAME2) in module
DGTFFOA2 is invalid.
0332
Incorrect number in the entry statement of the fixed area.
0333
TAGLEN value in module column DGTFFOI1 is invalid.
0334
No left parenthesis in the tag text.
0335
Length of the output variable is not equal to the length of the
data to be retrieved.
0336
Value of COLSIZE in module DGTFFOY1 is invalid.
0337
Length of the static load module text is invalid.
0338
Input parameter area option (AREAOP) is invalid.
0339
One of the control block lengths in the static load module is
incorrect.
0340
Invalid return code.
0341
Input parameter ADDRFAB is invalid.
0342
Input parameter CRPLAI or CRPVAL is invalid.
0343
FSAB exists without any FAB. Format services were not cleaned
up.
0344
Character scroll amount in DGTFFOM1 is invalid. Amount is neither
PAGE nor MAX.
0345
ISPF/PDF edit failed. Severe error, unable to continue. Return
code: 20.
0346
CLIST line operator canceled by user with END command.
0347
Object name (second column of list) is blank.
0348
DELETE failed because the list was generated from VTOC.
0349
Invalid column heading length. The column heading length obtained
from the message library is less than that stored in the static text,
or greater than the length of the data area in the list panel.
0350
DFHSM line operator failed.
0351
DFQFMACC failed to read MCVT, SVC error.
0352
DFQFMACC failed to read MCVT, MWE error.
0353
DFQFMACC failed to read BCDS (B Record), SVC error.
0354
DFQFMACC failed to read BCDS (B Record), MWE error.
0355
DFQFMACC failed to read BCDS (C Record), SVC error.
0356
DFQFMACC failed to read BCDS (C Record), MWE error.
TSO DELETE: Minor error encountered. Return code: 4.
0367
TSO DELETE: Function completed, but specific details were bypassed.
Return code: 8.
0368
TSO DELETE: Entire function could not be performed. Return code:
12.
0369
TSO DELETE: Severe error. Return code: 16.
0370
TSO DELETE: Severe error. Return code: 20.
0373
Data set name is unreadable '?????????'. Unable to alter data
set.
0374
ALTER line-op failed: severe error in DGTFAL04, or in DGTQAL01.
Unable to alter data set.
0375
ALTER line-op failed: severe error in DGTFAL05. Unable to alter
data set.
0400
Sort parameter is invalid.
0401
Filter syntax is invalid. Only one set of filter criteria may
be specified.
0402
Application filter-initialization module failed. Application did
not initialize appropriate filter control blocks.
0403
FILTER command was canceled by the user with the END command.
No filtering took place.
0404
No changes were detected in the filter criteria. List is already
filtered according to the specified filter criteria. No new filter
took place.
0405
Filter flags not properly initialized. One of the following flags
must be on: ADDFLAG, DELFLAG, or MODFLAG.
0406
Invalid filter type specified by the user, detected by the filter
module.
0407
Invalid relational operator specified by the user and not detected
by the filter panel definition. EQ or NE should have been specified.
0408
Invalid relational operator specified by the user. Valid relational
operators are: EQ, NE, GT, GE, LT, and LE.
0409
Column tag must be enclosed in parentheses.
0410
Panel name from the ERTB is invalid.
0411
Column name specified in the DAB is not recognized.
0412
Invalid relational operator. Only valid relational operators for
the specified column are EQ and NE.
0413
Invalid relational operator. Only valid relational operator for
the specified column is EQ.
0420
Invalid input parameter tags for module DGTFSO04.
0421
Filter value is longer than the allowed maximum length.
0450
Error occurred during DEVINFO invocation. Return code from DEVINFO
indicates that an error was encountered. Detailed information has
been placed in the problem determination area of the ISMF log.
0451
Respective field's displacement is zero in the return area header
of DEVINFO.
0452
Source for the generated list is invalid. Source of a generated
list should either be VTOC or CATALOG.
0453
Invalid connector was entered by the user, but was not detected
by the panel check routine.
0454
Invalid operator was entered by the user, but was not detected
by the panel check routine.
0455
Screen logical number obtained from the profile pool is either
invalid (<0) or not in the defined range (1 to 8).
0456
Requested column cannot be found in the data set application static
module.
0457
Invalid scroll amount was entered by the user.
0470
Conflict between CPPLPMAD and DGTEWORD. CPPLPMAD indicates that
there is a parameter, but the length of the parameter returned by
DGTEWORD is not greater than zero.
0471
Invalid pointer (GDRBIACB) to the first ISMF application control
block (IACB).
0472
An error exists in the chaining of IACBs.
0473
A conflict exists in the IACB pointers.
0474
The pointer (GDRBIACB) to the first IACB is 0.
0501
TBVCLEAR: Severe table error. Return code: 20.
0502
TBVCLEAR: Table not open. Return code: 12.
0504
TBSARG: Severe table error. Return code: 20.
0505
TBSARG: Table not open. Return code: 12.
0506
TBSARG: All column variables are null, and the namelist parameter
was not specified. No argument established. Return code: 8.
0507
TBSKIP: Severe table error. Return code: 20.
0508
TBSARG: Table not open. Return code: 12.
0509
TBSKIP: Variable value has been truncated, or insufficient space
was provided to return all extension variable names. Return code:
16.
0510
TBSKIP:Current row pointer would have gone beyond the number of
rows in the table (this includes a table empty condition). ISPF current
row pointer is set to 0 (top). Return code: 8.
0512
TBBOTTOM: Variable value has been truncated, or insufficient space
was provided to return all extension variable names. Return code:
16.
0513
TBBOTTOM: Severe table error. Return code: 20.
0514
TBBOTTOM: Table not open. Return code: 12.
0515
TBBOTTOM: Table is empty, CRP set to top (0). Return code: 8.
0516
TBBOTTOM: CRP set to top (0). Return code: 8.
0517
TBTOP: Severe table error. Return code: 20.
0518
TBTOP: Table not open. Return code: 12.
0519
TBSORT: Severe table error. Return code: 20.
0520
TBSORT: Table not open. Return code: 12.
0521
TBSORT: Numeric convert error. Return code: 16.
0522
TBPUT: Severe table error. Return code: 20.
0523
TBPUT: Table not open. Return code: 12.
0524
TBPUT: CRP was at top and remains at top. Return code: 8.
0525
TBPUT: Numeric conversion error. Return code: 16.
0526
Improper DAB variable type. It must be C, H, or B.
0527
Call to DELETE was unsuccessful.
0528
Array does not exist.
0529
Invalid sort order: It must be A or D.
0530
SELBFLG1 is not specified or is incorrectly specified. One bit
must be on.
0531
Caller's DAB does not match with any VDEFINE DABs.
0532
Scan for the nth row was unsuccessful. The last row found is returned.
0533
Improper search direction. Direction default is to next.
0534
DABL contains no DABs. Array cannot be created.
0535
Get storage for ARVT/RWCB control block failed.
0536
SRVTARB1 or SRVTARN1 (or both) in SRVT control block are not initialized.
0537
Extension DAB name is not returned in the extension variable list
by ISPF.
0538
DABCLEN is invalid.
0539
Array already exists.
0540
Invalid DAB justification flag.
0541
Condition value for an extension DAB is invalid.
0542
Return code is invalid.
0581
Convert utility: Address of the control data attribute block is
0.
0582
Data set name verification: invalid character. Valid characters
are: A-Z, 0-9, '#', '$', '@', '.', ')', '(', '*'. In addition, the
first character within a set of parentheses may be '+', '-', 0, alphabetic,
or national (@, $, #).
0583
Data set name verification: Incomplete data set name specification.
Data set name must not end with a '.'.
0584
Data set name verification: Data set name is quoted. Data set
name must not be quoted in this situation.
0586
Data set name verification: Invalid member name. Member name must
start with a national (@, $, #) or alphabetic character; subsequent
characters may also be numeric. Member name must not exceed 8 characters
in length.
0587
Data set name verification: Invalid member name. Member name must
not exceed 8 characters in length.
0588
Data set name verification: Invalid data set name. Member of a
PDS must not be specified.
0589
Data set name verification: Invalid generation data set specification.
GDG must be in the form (0), (+n), or (-n), where n is between 1 and
255.
0590
Data set name verification: Invalid data set name. Fully specified
data set names are not allowed.
0591
Data set name verification: Data set name is too long. Maximum
length, including '.', is 35 characters for a GDG data set name, and
44 characters for a fully specified data set name.
0592
Data set name verification: Invalid data set name. GDG specification
is not allowed.
0593
Data set name verification: Invalid partial specification. More
than 2 '*' in a single qualifier are not allowed.
0594
Data set name verification: Invalid data set name. Partial specification
is not allowed.
0595
Volser verification: Partial specification is not allowed. Partial
specification was not requested, but an '*' was found in the input
volume serial number.
0596
Volser verification: Full specification is not allowed. Input
volser was fully specified, but full specification was not requested.
0597
Log Utility: Request was made to log abend information, but the
pointer to the retry work area (RWA) is not valid.
0598
Data set name verification: Qualifier was found that was longer
than the allowable maximum of 8 characters.
0599
Data set name verification: Invalid qualifier specification. First
character of a qualifier must be alphabetic or national (#, @, $).
0600
MVS load SVC was unsuccessful. Requested module could not be loaded.
0601
No matching SCT entry was found.
0602
Unable to build storage control (SCT) entry.
0603
Reserved for CSR, DGTCGMO1. Return code: 8.
0604
Unable to build load list block (LLBL) entry.
0605
No matching LLBL entry found.
0606
Load common service routine failed while trying to link to another
module with the ISMF link macro.
0607
Tried to decrement when use count=0.
0608
Convert utility: Truncated data. Target area specified was not
large enough to contain the converted data. Data was truncated.
0610
Convert utility: Length of the source data must be from 1 to 4
bytes when converting fixed binary numbers.
0611
Convert utility: Invalid source data length. Length of the data
to be converted must be greater than 0.
0612
Convert utility: Target data length is invalid. Length of the
target data must be greater than 0.
0613
Convert utility: Source data address=0. Address of the data to
be converted is 0.
0614
Convert utility: Target address=0. Address specified for the target
address is 0.
0615
Data set name (DSN) verification failed.
0616
Starting address is larger than ending address. Input parameters
supplied to the word-parsing routine (DGTEWORD) are invalid.
0617
Log: Message not found. Return code: 12.
0618
Log: Severe error. Return code: 20.
0619
Log: Invalid return code.
0620
Request was made to log status information, but no additional
message IDs were specified. At least one message ID must be specified.
0621
Convert utility: Invalid conversion code.
0622
Convert utility: Invalid justification code.
0623
Data set name verification: Unbalanced quotes were found in the
input data set name. Data set name may contain no quotes or two quotes
(one at each end of the data set name).
0624
Invalid return code from ISPF VDELETE.
0625
Invalid return code from ISPF VPUT.
0626
Invalid return code from ISPF VGET.
0627
Invalid return code from ISPF VDEFINE.
0628
Invalid return code from ISPF SETMSG.
0629
Invalid return code from ISPF GETMSG.
0630
Invalid return code from ISPF DISPLAY.
0631
ISPF DISPLAY: Terminated by END or RETURN. User requested termination
by using END or RETURN command. Return code: 8.
0632
ISPF DISPLAY: Specified panel, message, or cursor field was not
found. Return code: 12.
0633
ISPF DISPLAY: Truncation or translation error in storing defined
variables. Return code: 16.
0634
ISPF DISPLAY: Severe error. Return code: 20.
0635
ISPF GETMSG: Specified message was not found. Return code: 12.
0636
ISPF GETMSG: Severe error. Return code: 20.
0637
ISPF SETMSG: Specified message was not found. Return code: 12.
0638
ISPF SETMSG: Severe error. Return code: 20.
0639
ISPF VDEFINE: Variable was not found. Return code: 8.
0640
ISPF VDEFINE: Data truncation occurred. Return code: 16.
0641
ISPF VDEFINE: Severe error. Return code: 20.
0642
ISPF VGET: Variable was not found. Return code: 8.
0643
ISPF VGET: Truncation or translation error occurred during data
movement. Return code: 16.
0644
ISPF VGET: Severe error. Return code: 20.
0645
ISPF VPUT: Variable was not found. Return code: 8.
0646
ISPF VPUT: Truncation occurred while copying variables to the
application profile pool. Return code: 16.
0647
ISPF VPUT: Severe error. Return code: 20.
0648
ISPF VDELETE: At least one variable was not found. Return code:
8.
0649
ISPF VDELETE: Severe error. Return code: 20.
0650
ISPF TBDELETE: For nonkeyed tables, the table was empty. ISPF
current row pointer remains at the top. For keyed tables, the row
specified by the key variables does not exist. ISPF current row pointer
is set to top. Return code: 8.
0651
ISPF TBDELETE: Table is not open.
0652
ISPF TBDELETE: Severe error.
0653
ISPF TBDELETE: Return code is invalid.
0654
ISPF TBEND: Table is not open.
0655
ISPF TBEND: Severe error.
0656
ISPF TBEND: Return code is invalid.
0657
ISPF TBTOP: Table is not open.
0658
ISPF TBTOP: Severe error.
0659
ISPF TBTOP: Return code is invalid.
0660
ISPF TBVCLEAR: Table is not open.
0661
ISPF TBVCLEAR: Severe error.
0662
ISPF TBVCLEAR: Return code is invalid.
0663
ISPF TBADD: Row with the same key already exists. ISPF current
row pointer is set to the top (0). Return code: 8.
0664
ISPF TBADD: Table is not open.
0665
ISPF TBADD: Numeric convert error.
0666
ISPF TBADD: Severe error.
0667
ISPF TBADD: Return code is invalid.
0668
ISPF TBPUT: For nonkeyed tables, the ISPF current-row pointer
was at the top and remains at the top. For keyed tables, the key does
not match that of the current row. ISPF current row pointer is set
to the top. Return code: 8.
0669
ISPF TBPUT: Table is not open.
0670
ISPF TBPUT: Numeric convert error.
0671
ISPF TBPUT: Severe error.
0672
ISPF TBPUT: Return code is invalid.
0673
ISPF TBGET: For nonkeyed tables, the ISPF current-row pointer
was at the top and remains at the top. For keyed tables, the row specified
by the value in the key variables does not exist. The ISPF current
row pointer is set to the top.
0674
ISPF TBGET: Table is not open.
0675
ISPF TBGET: Insufficient space to return all extension variable
names.
0676
ISPF TBGET: Severe error.
0677
ISPF TBGET: Return code is invalid.
0678
ISPF TBCREATE: Table already exists.
0679
ISPF TBCREATE: Table in use, ENQ failed.
0680
ISPF VCOPY: Variable not found. Return code: 8.
0681
ISPF TBCREATE: Severe error.
0682
ISPF TBCREATE: Return codes are invalid.
0683
ISPF TBSORT: Table is not open.
0684
ISPF TBSORT: Numeric convert error.
0685
ISPF TBSORT: Severe error.
0686
ISPF TBSORT: Return code is invalid.
0687
ISPF TBBOTTOM: Table is empty.
0688
ISPF TBBOTTOM: Table is not open.
0689
ISPF TBBOTTOM: Insufficient space provided to return all extension
variables.
0690
ISPF TBBOTTOM: Severe error.
0691
ISPF TBBOTTOM: Return code is invalid.
0692
ISPF TBSARG: All column variables are null, and the name-list
parameter was not specified.
0693
ISPF TBSARG: Table is not open.
0694
ISPF TBSARG: Severe error.
0695
ISPF TBSARG: Return code is invalid.
0696
ISPF TBSKIP: CRP would have gone beyond the number of rows in
the table.
0697
ISPF TBSKIP: Table is not open.
0698
ISPF TBSKIP: Insufficient space was provided to return all extension
variables.
0699
ISPF TBSKIP: Severe error.
0700
ISPF TBSKIP: Return code is invalid.
0701
ISPF TBSCAN: Row does not exist. No match was found.
0702
ISPF TBSCAN: Table is not open.
0703
ISPF TBSCAN: Insufficient space was provided to return all extension
variables.
FTCLOSE: Output file is not allocated. Return code: 16.
0714
FTCLOSE: Severe error. Return code: 20.
0715
FTCLOSE: Return code from ISPF is invalid.
0716
FTINCL: Skeleton does not exist. Return code: 8.
0717
FTINCL: Skeleton or table in use. Return code: 12.
0718
FTINCL data truncation occurred, or skeleton library or output
file esd not allocated. Return code: 16.
0719
FTINCL: Severe error. Return code: 20.
0720
FTINCL: Return code from ISPF is invalid.
0721
FTOPEN: File tailoring already in progress. Return code: 8.
0722
FTOPEN: Output file in use. Return code: 12.
0723
FTOPEN: Skeleton library or output file was not allocated. Return
code: 16.
0724
FTOPEN: Severe error. Return code: 20.
0725
Return code from ISPF is invalid.
0726
TBQUERY: Table is not open. Return code: 12.
0727
TBQUERY: Insufficient space provided. Return code: 16.
0728
TBQUERY: Severe error. Return code: 20.
0729
TBQUERY: Unexpected return code.
0730
ISPF VCOPY: Invalid return code.
0731
PDF LMINIT: DATA-ID not created. The error condition is described
in the ISPF system dialog variables. Return code: 8.
0732
PDF LMMLIST: Empty member list. Return code: 4.
0733
PDF LMMLIST: LIST OPTION - End of member list. Return code: 8.
PDF LMMLIST: FREE OPTION - Member list does not exist.
0734
PDF LMMLIST: No data set associated with the given DATA-ID. That
is, LMINIT has not been completed. Return code: 10.
0735
PDF LMMLIST: One of the following: The data set is not open or
is not partitioned. The parameter value is invalid. Return code: 12.
0736
PDF LMMLIST: Truncation or translation error in accessing dialog
variables. Return code: 16.
0737
PDF LMMLIST: Severe error, unable to continue. Return code: 20.
0738
PDF LMMLIST: Invalid return code.
0739
Table service failed, list may be incomplete.
0740
Index is not within bounds of the array.
0741
TBSTATS: Variable value has been truncated.
0742
TBSTATS: Severe error.
0743
TBSTATS: Invalid return code.
0806
Load module was not found.
1000
Invalid (unexpected) return code was received from the called
function. This could be due to a logic error in the called function
or a mismatch between calling and called function. For example, the
called function might have added a new return code of which the caller
is not aware.
1001
CDTXSTAT field of CDTX contains an unrecognizable value.
1002
Visual ID of the control block is invalid. This could be caused
by an invalid address in the pointer to the control block or by incorrect
initialization of the visual ID of the control block.
1003
Function requested by the caller is invalid.
1004
Value of the DACDTOT field of DACD does not correspond to the
total number of DSN DABs.
1005
While preparing to update the filter status field (DABFS), the
DSN DAB was not found.
1006
DYNALLOC Error.
1007
RDJFCB Error.
1008
Open Error.
1009
Duplicate column name in DAB.
1010
Column name in DAB is invalid.
1011
DACL is invalid.
1012
Duplicate DACL.
1013
Column name in DACL is invalid.
1014
More than one DSN was specified for generic DSN.
1015
Percent of ALLOC not used cannot be calculated because either
the allocated space or the allocation used is invalid.
1016
GFL error: Nonzero return code.
1017
GFL error: Catalog name entry.
1018
GFL error: Data set name entry.
1019
GFL error: The length was invalid.
1020
Status of the data set name (FCLDSNST) returned by CVAFFILT in
FCL is invalid.
1021
TRKCALC error.
1022
DASDCALC error.
1023
DEVINFO error.
1024
CVAFFILT error.
1025
DFSMShsm is
not installed or is inactive.
1026
Volume serial number verification: An invalid character was found.
1027
Volume serial number verification: Too many asterisks were found.
Only one asterisk may be specified in a partial specification.
1028
Invalid operator was found in DACL during selection criteria processing.
1029
Invalid logical connector was found in DACL during selection criteria
processing.
1030
GFL error: No data is returned.
1031
Nonzero return code from catalog management.
1032
Unable to acquire needed data.
1033
Needed data from SWAREQ not acquired.
1034
Percentage of user data reduction cannot be calculated.
1047
Error acquiring data needed to invoke DASDCALC.
1048
Error acquiring keyrange qualifier.
1049
Error acquiring volume flag.
1050
Data set is not partitioned.
1051
Data set does not have SAM/PAM DSORG.
1052
Locate failed. See feedback for catalog reason code.
1053
Unable to locate cluster name for VSAM component.
1054
Data set name is GDG base name.
1055
Data set name is VSAM data or index component name.
1056
Data set's allocated used space is 0.
1057
Data set is migrated.
1058
Submit failed.
1059
RESTORE LIST command invalidly entered on a selection panel.
1060
RESTORE command parameter is neither list nor data set.
1061
More than one RESTORE command parameter entered.
1062
Output data set for background job is neither physical sequential
nor a member of a PDS.
1063
Select failed. See feedback field for select return code.
1064
Return code from DYNALLOC is 0, but the SVC99 information reason
code is not 0. See feedback for SVC99 request type, error reason code,
and information reason code.
1065
Return code from DYNALLOC is 4. See feedback for SVC99 request
type, error reason code, and information reason code.
1066
Return code from DYNALLOC is 8. See feedback for SVC99 request
type, error reason code, and information reason code.
1067
Return code from DYNALLOC is 12. See feedback for SVC99 request
type, error reason code, and information reason code.
1069
VSAM component name found in catalog.
1070
System residence volume serial number (ETSYSRES) in environment
table is blank.
1071
Return code from DEVINFO is 0 or 8. UCBTYP is not DASD.
1072
Data set is a user catalog.
1073
Unexpected allocation request type received during background
job submission. See feedback for unexpected allocation request type.
1074
Invalid parameter entered on the command line.
1075
Volser verification: is blank.
1076
Volser verification: is a single asterisk.
1077
No column name match found in static column load module. See feedback
for column name requested and static column load module name.
1078
No column name match was found in the DAB chain.
1079
Unexpected panel number was encountered. See feedback field for
unexpected panel number.
1080
Unexpected panel variable name was encountered. See feedback field
for unexpected panel name.
1081
Unexpected catalog entry type was received back from call to DGTEARFN.
1082
Unexpected column name was encountered during verification of
data sets in the list. See feedback for unexpected column name.
1083
Unexpected request type was received during array processing.
See feedback for the unexpected request type.
1084
No data set names found in the array.
1085
Unexpected file tailoring service was requested during background
job submission. See feedback for the unexpected tailoring service
name.
1086
Unexpected request type was received during filter data set allocation
processing. See feedback for the unexpected request type.
1087
Open error: See feedback for indication of whether data set was
input or output, return code from open, and data set name.
1088
Duplicate data set name found in data set list.
1089
Unexpected DCB address was found during background job submission.
See feedback for current DCB address and all 3 valid DCB addresses.
1090
More than 255 input volume serial numbers.
1091
Data set name is VSAM cluster name.
1092
Unexpected option flag received during the process of validating
the data set name. See feedback field for the unexpected option field.
1093
Unexpected GETMAIN request flag received. See feedback for the
unexpected request flag value.
1094
Unexpected job disposition type received during background job
submission. See feedback for the unexpected job disposition type.
1095
Close error: See feedback for indication of whether data set was
input or output, return code from close, and data set name.
1096
Invalid request flag found during BUILD/DELETE of data set name
lists. See feedback for flag byte.
1097
Volser is null or in error.
1098
Output data set for a background job is not a PDS. (See feedback
for hexadecimal DSORG value and data set name.)
1099
BLDL failed.
1101
Invalid RESTORE parameter was entered on the data set selection
panel.
1102
Invalid job submitted message from CLIST DGTQSU01 submit processing.
1103
Device type is null or in error.
1104
ISPF TBOPEN: Table does not exist.
1105
ISPF TBOPEN: Enqueue failed, table in use.
1106
ISPF TBOPEN: Table input library not allocated.
1107
ISPF TBOPEN: Severe error.
1108
ISPF TBOPEN: Invalid return code.
1109
ISPF TBCLOSE: Table is not open. Return code: 12.
1110
ISPF TBCLOSE: Table output library is not open. Return code: 16.
1111
ISPF TBCLOSE: Severe error. Return code: 20.
1112
ISPF TBCLOSE: Unexpected return code.
1113
Last use mode is undefined for hide.
1114
Unable to build DEVT table.
1115
Nonzero return code from DGTCDT01.
1200
Error acquiring volser.
1201
Error acquiring use attribute.
1202
Error acquiring device number.
1203
Error acquiring device type.
1204
Error acquiring cylinders per volume.
1205
Error acquiring free extents.
1206
Error acquiring free cylinders.
1207
Error acquiring additional free tracks.
1208
Error acquiring cylinders in largest free extent.
1209
Error acquiring additional tracks in largest free extent.
1210
Error acquiring format-0 DSCB count.
1211
Volume capacity cannot be calculated because needed data was not
acquired.
1212
Free space cannot be calculated because needed data was not acquired.
1213
Percent free space cannot be calculated because needed data was
not acquired.
1214
Percent free space cannot be calculated because needed data has
invalid value.
1215
Allocated space cannot be calculated because needed data was not
acquired.
1216
Largest extent cannot be calculated because needed data was not
acquired.
1217
Cannot determine if DASD is shared because needed data was not
acquired.
1218
LSPACE error.
1219
LSPACE cannot be invoked because UCB address was not acquired.
1220
Error acquiring tracks per cylinder.
1221
VTOC size cannot be acquired because needed data cannot be acquired.
1222
Not authorized to access locked catalog.
1223
Catalog temporarily unavailable.
1224
Unauthorized locked catalog was encountered during a search of
catalogs for data sets that meet the partially specified data set
name.
1225
Catalog temporarily unavailable while searching catalogs for data
sets that meet the partially specified data set name.
1226
Specified catalog does not exist.
1230
Invalid criteria name specified in IACL. See feedback for invalid
name.
1231
Device type verification: Invalid character found.
1232
Device type verification: Device type is blank.
1233
Device type verification: More than one asterisk was specified
in a partial specification.
1234
Device type verification: Partial specification was not requested,
but an asterisk was found in the input device name.
1235
Device type verification: Full specification was not requested,
but no asterisk was specified.
1236
Device type verification: Device type is a single asterisk.
1237
Device type verification: Device type is not a supported generic
name.
1238
TBMOD: Keys did not match, new row added to table. Return code:
12.
1239
TBMOD: Table is not open. Return code: 12.
1240
TBMOD: Numeric conversion error. Return code: 12.
1241
TBMOD: Severe error. Return code: 12.
1242
TBMOD: Invalid return code. Return code: 12.
1243
TBERASE: Table does not exist in the output library. Return code:
12.
1244
TBERASE: Table in use, ENQ failed. Return code: 12.
1245
TBERASE: Output library not allocated. Return code: 12.
1246
TBERASE: Severe error. Return code: 12.
1247
TBERASE: Invalid return code. Return code: 12.
1248
VIEW: View failed. Return code: 12.
1250
Save command error: Invalid list name. List name cannot begin
with 'ISR', 'ISP', or 'DGT' and it cannot be quoted.
1252
ALTER error: Data set ALTER against a non-SMS-managed data set
is not allowed.
1253
Data set is a VSAM alternate index.
1254
ALTER error: Nonzero return code from SVC 26 ALTER. See feedback
for return code and reason code.
1255
Data set has unexpected type of catalog entry.
1256
SUBMIT error: Invalid job submitted message from CLIST DGTQSF01.
1257
Caller requested an invalid execute statement panel.
1258
Storage group name longer than the 8-byte maximum.
1259
Error in CSI GETLIST.
1260
Error in AOMSERV.
1261
DEVINFO resume is not allowed.
1262
Invalid input parameters.
1263
SCRATCH error: No volumes containing any part of the data set
were mounted. The data set may be a VIO data set that was not allocated
during SCRATCH. Return code: 4.
1264
SCRATCH error: Unusual condition was encountered on one or more
volumes. Return code: 8.
OBTAIN error: For return code 04, volume was not mounted; for
return code 08, DSCB was not found; for return code 12, I/O error;
for return code 16, invalid pointer.
1269
Variable data set record format was specified; must be fixed format.
1270
Repeat line operator used without previous line operator.
1271
Error occurred during processing of user line operator or command.
1272
VREPLACE: Truncation occurred during data movement.
1273
VREPLACE: Severe error.
1274
VREPLACE: Invalid return code.
1275
Error occurred during creation of user command anchor block.
1276
Invalid application ID for this service.
1277
User command failed.
1278
Failure occurred during processing of a list.
1279
Error occurred during initialization of user command.
1280
Invalid return code for user command initialization.
1281
User command control variable could not be retrieved from shared
variable pool.
1282
Error occurred in DSERVXIT.
1283
Invalid area specified. Valid values are ALL, DATA, or BOTH.
1284
Invalid value was specified for FROM. Valid values are LAI or
SLAI.
1285
Format name in data set anchor block is invalid.
1286
DSERVXIT cannot be invoked because UCB address was not acquired.
1287
Could not position CRP to top of array.
1288
AOMSERV returned nonzero return/reason code.
1289
Invalid subroutine call to DGTFCBSB.
1290
Could not position to top of array.
1291
Error during LASB initialization.
1292
PDF LMINIT: Invalid parameter value. Return code: 12.
1293
PDF LMINIT: Truncation or translation error in accessing dialog
variables. Return code: 16.
1294
PDF LMINIT: Severe error. Return code: 20.
1295
PDF LMINIT: Invalid return code.
1296
PDF LMOPEN: Data set could not be opened. Return code: 8.
1297
PDF LMOPEN: No data set associated with the given data ID. Return
code: 10.
1298
PDF LMOPEN: Invalid parameter value; data set is already open;
cannot open concatenated data sets for output; cannot open a data
set allocated SHR for output; cannot open a data set allocated MOD
for input. Return code: 12.
1299
PDF LMOPEN: Truncation or translation error in accessing dialog
variables. Return code: 16.
1300
PDF LMOPEN: Severe error. Unable to continue. Return code: 20.
1301
PDF LMOPEN: Invalid return code.
1302
PDF LMCLOSE: Data set is not open. Return code: 8.
1303
PDF LMCLOSE: No ISPF library or data set is associated with the
given data ID. Return code: 10.
1304
PDF LMCLOSE: Severe error. Unable to continue. Return code: 20.
1305
PDF LMCLOSE: Invalid return code.
1306
PDF LMFREE: Free data set failed. Return code: 8.
1307
PDF LMFREE: No data set is associated with the given data ID.
Return code: 10.
1308
PDF LMFREE: Severe error. Unable to continue. Return code: 20.
1309
PDF LMFREE: Invalid return code.
1310
PDF LMGET: No ISPF library or data set is associated with the
given data ID. Return code: 10.
1311
PDF LMGET: Data set is not open or is not open for input; LMMFIND
not done for a partitioned data set; invalid parameter value. Return
code: 12.
1312
PDF LMGET: Truncation or translation error in accessing dialog
variables. Return code: 16.
1313
PDF LMGET: Severe error. Return code: 20.
1314
PDF LMGET: Invalid return code.
1315
Cannot process command against empty list.
1316
Convert utility: Invalid packed decimal field found while doing
a date conversion.
1317
Largest extent in the track-managed space cannot be calculated
because some needed data was not acquired.
1318
Error acquiring cylinders in the largest free extent in the track-managed
space.
1319
Error acquiring additional tracks in the largest free extent in
the track-managed space.
1320
Error acquiring free cylinders in the track-managed space.
1321
Error acquiring additional free tracks in the track-managed space.
1322
Allocated space in the track-managed space cannot be calculated
because some needed data was not acquired.
1323
Free space in the track-managed space cannot be calculated because
some needed data was not acquired.
1324
Volume capacity in the track-managed space cannot be calculated
because some needed data was not acquired.
1325
VTOCLIST line operator not allowed for migrated data set (DS in
the MIGRAT VOLSER).
1326
SMS GETMAIN failed.
1327
Storage group volumes copy - duplicate volume.
1328
VTOCLIST line operator is not allowed for the data set.
3000
ESTAE macro invocation failed with return code 4.
3001
ESTAE macro invocation failed with return code 8.
3002
ESTAE macro invocation failed with return code 12.
3003
ESTAE macro invocation failed with return code 16.
3004
ESTAE macro invocation failed with return code 20.
3005
ESTAE macro invocation failed with return code 24.
3006
ESTAE macro invocation failed with an unknown return code.
3007
ISPLINK (CONTROL) service failed with return code 20.