Explanation
Where
text is:
ID STATE ID STATE ID STATE ID STATE
xxxx state xxxx state xxxx state xxxx state
ID=xxxx [,IDGROUP=opt], type, state, [DEBUG]
ACTION=opt, SET BY id-orig
[,RBLEVEL=opt]
[COMP=opt]
[JOBNAME=opt]
[JSPGM=opt]
[JOBLIST=opt]
{PVTMOD=opt|PVTEP=opt|LPAMOD=opt|LPAEP=opt|NVCMOD=opt
|NVCEP=opt|ADDRESS=opt}
[RANGE=opt]
[EVALUATED RANGE=opt]
[PRCNTLIM=opt,p]
[,MATCHLIM=opt,m]
[REASON=opt]
[ASID=opt]
[ERRTYP=opt]
[MODE=opt]
[SDATA=opt]
[ASIDLST=opt] [DSPNAME=opt] [DATA={u|(u,tx)},opt]
[SUMLIST=opt] [LIST=opt]
[TRDATA=opt] [ASIDSA=opt] [DSSA=opt]
[PSWASC=opt] [REMOTE=opt] [STRLIST=opt]
[TARGETID=opt] [REFBEFOR=opt] [REFAFTER=opt]
[TXIGD=opt]
A DISPLAY SLIP command requested the display of
SLIP trap information. The system issues this message in response
to that command. For DISPLAY SLIP, DISPLAY SLIP=xxxx
(where xxxx has a wildcard character *), DISPLAY SLIP,PER and DISPLAY
SLIP,ENIPT only the ID/STATE column header and values are displayed.
For DISPLAY SLIP=xxxx (where xxxx has no wildcard character *), all
lines except the ID/STATE column header and values may be displayed.
In
the first line of the message text:
- hh.mm.ss
- The time, in hours (00 through 23), in minutes (00 through 59),
and in seconds (00 through 59). If hh.mm.ss is
00.00.00, then the TOD clock was not working when SLIP displayed the
information.
- idr
- A 3-digit decimal identifier used with the CONTROL C,D command
to cancel status displays either:
- Written on typewriter or printer consoles
- Displayed in-line (not in a display area) on display (CRT) consoles
This identifier does not appear when the display is presented
in a display area on a display console.
The second and third lines of the message
appear when a DISPLAY SLIP command is entered without a SLIP trap
identifier.
In the second and third lines of the message text:
- ID
- xxxx
- The SLIP trap identifier specified on the SLIP command.
- STATE
- state
- The state of the SLIP trap: ENABLED,ENAB/I,DISABLED.
For
DISPLAY SLIP, the possible STATE values are ENABLED and DISABLED.
For
DIPLAY SLIP,PER, the STATE value will be one of:
- ENABLED - The trap is ENABLED and is not ACTION=IGNORE.
- ENAB/I - The trap is ENABLED and is ACTION=IGNORE.
- DISABLED - The trap is DISABLED.
For DISPLAY SLIP,ENIPT the STATE will be ENABLED.
The remaining lines appear when a DISPLAY
SLIP=xxxx command is entered. The type of SLIP trap and the options
chosen when the trap was defined determine which fields appear, as
follows:
- ID=xxxx
- The SLIP trap identifier entered in the DISPLAY command.
- type
- The type of SLIP trap:
- NONPER
- Not a program event recording (PER) trap.
- PER-IF
- PER instruction fetch trap.
- PER-SA
- PER storage alteration trap.
- PER-SB
- PER successful branch trap.
- PER-SB1
- PER 1 successful branch trap.
- PER-SBT
- PER 1 successful branch into (SBT) trap.
- PER-SAS
- PER storage alteration by STORA (SAS) trap.
- PER-ZAD
- PER zero address detection trap.
- state
- The state of the SLIP trap:
- ENABLED(ACTIVE)
- The system found the private module specified in the PVTMOD or
PVTEP parameter, as by a LOAD, and has activated the enabled trap.
- ENABLED(INACTIVE)
- One of the following:
- The system did not find the private module specified in the PVTMOD
or PVTEP parameter.
- The system deactivated the enabled trap, as by a DELETE.
- ENABLED
- The system enabled the trap.
- DISABLED
- The system disabled the trap.
- ACTION=opt
- The option specified in the ACTION parameter.
- SET BY id-orig
- id-orig identifies the originator of this SLIP
trap, which is one of the following:
- TSO userid
- The Time Sharing Option Extensions (TSO/E) user, if the SLIP trap
was defined through a TSO/E terminal.
- CONS consname
- The console name, if the SLIP trap was defined through a console.
- opt
- The option or options specified directly or by default in the
SLIP command that defined this SLIP trap.
- PRCNTLIM=opt,p
- p is the actual percentage of system processing
time used to process PER interruptions, beginning with the first PER
interruption processed for this SLIP trap. If the percentage cannot
be calculated, p is one of the following:
- NA
- The calculation is not applicable. Either the trap is disabled
or PRCNTLIM=99 was specified for the trap definition.
- LT
- Less than 33 seconds has elapsed since SLIP processed the first
PER interruption for this trap.
- CK
- The time-of-day clock is in error.
- BC
- The system contains an incorrect value for the number of in-line
processors.
- MATCHLIM=opt,m
- m is the number of times that the conditions
for this SLIP trap were met since the last time the trap was enabled.
- DATA={u|(u,tx)},opt
- u is the number of times that the SLIP processor
could not access the data in a target location because the data was
unavailable. This failure can occur if either the data itself or an
indirect pointer to the data was paged out when SLIP processing attempted
to access the data.
tx is the number of times
that the DATA keyword did not match when the event occurred in transactional
execution mode. The maximum value is 255. If the value is 255, there
could have been more than 255 mismatches.
- TXIGD=opt
- opt is whether or not TXIGD has been requested
on the SLIP command.
- PER
- The STATE will be one of the following:
- ENABLED
- The trap is ENABLED and is not ACTION=IGNORE.
- ENAB/I
- The trap is ENABLED and is ACTION=IGNORE.
- DISABLED
- The trap is DISABLED.
- ENIPT
- The STATE will be ENABLED (the trap being shown is not ACTION=IGNORE
and is not DISABLED).
System action
The system continues processing.
Source
Recovery termination manager (RTM)
Module
Routing code
Descriptor code