A fix is available
APAR status
Closed as program error.
Error description
APAR for CM z/OS 8.5.0 Library Server fix pack 6 roll-up PTF Additional Keywords: LS fp6 fixpak fixpack
Local fix
N/A
Problem summary
**************************************************************** * USERS AFFECTED: Users of IBM(R) Content Manager for z/OS(R) * * V8.5.0 library server * **************************************************************** * PROBLEM DESCRIPTION: This PTF is a roll-up of several * * IBM(R) Content Manager for z/OS V8.5.0 * * library server APARs that have been * * reported since the release of the * * Fix Pack 5 PTF for that product * * (UI32267). This roll-up PTF will be * * referenced in documentation as the * * "IBM(R) Content Manager for z/OS V8.5.0 * * library server Fix Pack 6 PTF". * * * * The included APARs are: * * * * APAR # Description * * ------- ------------------------------ * * PI60151 Library server monitor * * heart beat incorrectly * * marks resource manager * * as unavailable. * * PI64680 High volume batch utility * * is not processing all input * * when stopcount is used. * * PI67963 Importing itemtype definitions * * to create itemtypes is getting * * unexpected error with SQL * * error -519. * * * **************************************************************** * RECOMMENDATION: APPLY CORRECTIVE SERVICE * **************************************************************** This is a roll-up PTF. Refer to the Problem Description section for more detail.
Problem conclusion
This is a roll-up PTF. All APARs listed in the Problem Description are resolved in this PTF. HOLD (DOC) ---------------------------------------------------------------- Also see the "IBM Content Manager Version 8 Release 5 Modification 0 Fix Pack 6 readme" at http://www.ibm.com/support/knowledgecenter/SSRS7Z_8.5.0/--> -->readme/CM_8.5.0.6_fix_pack_readme.html for further information. HOLD (DOC) ---------------------------------------------------------------- Also see "System requirements: Hardware and software requirements for IBM Content Manager for z/OS Version 8.5.0 Fix Pack 6" at http://www.ibm.com/support/docview.wss?uid=swg27038463 for further information. HOLD (ACT) ---------------------------------------------------------------- You can use the IBM(R) Content Manager for z/OS Job Configuration tool to upgrade to V8.5.0 Fix Pack 6. If your product level, before upgrade, is at the V8.5.0 GA level, you must select the 'Fix pack upgrade only' panel (panel ID: ICMMFPLV) to customize your upgrade jobs. Enter 6 in the 'Fix pack number before the upgrade' field. If your product level, before upgrade, is not at the V8.5.0 GA level, you must select the 'Version, release, modification, and fix pack upgrade' panel (panel ID: ICMMUPLV) to customize your upgrade jobs. The tool will upgrade your system to the most current fix pack level of V8.5.0. The minimum product level is V8.4.3 or above for upgrading to V8.5.0 Fix Pack 6. You need to customize JCLs manually if they are not supported in the Job Configuration tool. HOLD (ACT) ---------------------------------------------------------------- Data provided in the SQL statements in the SYSIN in the ICMMLSLD and ICMMLSUP jobs contains national language character If the dollar sign has different code point in your DB2 subsystem code page, specify a DB2 plan for DSNTIAD which is bound with the ENCODING bind option ENCODEING(1047) so DB2 will convert the dollar sign properly. HOLD (ACT) ---------------------------------------------------------------- For newly-installed IBM(R) Content Manager for z/OS V8.5.0 library servers, customize and run the ICMMLSCR, ICMMLSLD, ICMMLSBD, ICMMLSGT, and ICMMCACL post-installation jobs at the latest level to create a library server database, as described in the Planning and Installing Your Content Management System for z/OS guide. After you run the jobs, your library server will be at the base level and will require an upgrade to Fix Pack 6. To upgrade an existing IBM(R) Content Manager for z/OS library server to the IBM(R) Content Manager for z/OS V8.5.0 Fix Pack 6 level, perform the following steps: 1. Run the applicable steps of the ICMMLSUP library server database upgrade job, as documented in the comments within ICMMLSUP. 2. Run the ICMMLSBD library server bind job again. The package version id FP6_850006 is used for supporting the package versioning. 3. Run the ICMMLSGT library server grant job again. 4. Start the work load manager where the IBM(R) Content Manager for z/OS V8.5.0 Fix Pack 6 resides. 5. Skip this step if ICMMLSU2 job was run during the IBM(R) Content Manager for z/OS V8.5.0 Fix Pack 1 migration. Otherwise, run ICMMLSU2 job to convert RMPASSWORD to RMPASSWORD2 in the ICMSTResourceMgr table. 6. From a command prompt on the computer from which you run the Content Manager system administration client, run cmcfglsi -t comptypes again. (Note - if you have already installed Content Manager for z/OS V8.4.3 Toolkit Fix Pack 2 or later, you may run the command from a Unix System Services shell under z/OS instead.) To revert back to Content Manager for z/OS library V8.5 GA or V8.4.3, you must run the ICMMLSU3 job. But if you created any new sub component type view after you install V8.5.0 Fix Pack 6 then you need to drop these sub view(s) before you run the ICMMLSU3 job. The V8.5.0 Fix Pack 6 library server must be active in order for the ICMMLSU3 job to run successfully. You must also replace RELNAME1, RELNAME2 and RELNAME3 in ICMMLSU3 before you submit the job. Refer to http://www-01.ibm.com/support/docview.wss?uid=swg21672831 for related information. HOLD (ACT) ---------------------------------------------------------------- The following customizable JCL and data members are modified by this PTF. If you have modified the originals, you might want to compare them to the new versions: ICMMLSLD - Set current version to Fix Pack 6 ICMMLSUP - Set current version to Fix Pack 6 and update comments HOLD (ACT) ---------------------------------------------------------------- The program ICMPBL02 to generate batch load program source code is changed. If you use high volume batch load utility, you must regenerate the batch load program for any item types with a child component.
Temporary fix
Comments
APAR Information
APAR number
PI68382
Reported component name
CM390 LIB SER R
Reported component ID
5697H6000
Reported release
850
Status
CLOSED PER
PE
NoPE
HIPER
NoHIPER
Special Attention
NoSpecatt / Xsystem
Submitted date
2016-08-31
Closed date
2016-11-28
Last modified date
2017-01-03
APAR is sysrouted FROM one or more of the following:
APAR is sysrouted TO one or more of the following:
UI42944
Modules/Macros
ICMFLS1 ICMFRM ICMMLSAP ICMMLSLD ICMMLSUP ICMPBL01 ICMPBL02 ICMPBL05 ICMPCOF3 ICMPCOSK ICMPDREP ICMPDRGW ICMPDRIT ICMPDRSP ICMPDRUP ICMPIID2 ICMPLSAD ICMPLSAP ICMPLSBO ICMPLSBV ICMPLSCE ICMPLSCI ICMPLSCO ICMPLSCP ICMPLSCV ICMPLSC1 ICMPLSC2 ICMPLSDD ICMPLSDI ICMPLSEI ICMPLSGI ICMPLSIT ICMPLSIV ICMPLSI2 ICMPLSKM ICMPLSLF ICMPLSLG ICMPLSLI ICMPLSP1 ICMPLSP2 ICMPLSP3 ICMPLSP4 ICMPLSP5 ICMPLSRC ICMPLSRI ICMPLSSC ICMPLSS2 ICMPLSTE ICMPLSTT ICMPLSUC ICMPLSUO ICMPLSUR ICMPLSU1 ICMPLSU2 ICMPRMRC ICMPRMUO
Fix information
Fixed component name
CM390 LIB SER R
Fixed component ID
5697H6000
Applicable component levels
R850 PSY UI42944
UP16/12/12 P F612
Fix is available
Select the PTF appropriate for your component level. You will be required to sign in. Distribution on physical media is not available in all countries.
[{"Business Unit":{"code":"BU053","label":"Cloud & Data Platform"},"Product":{"code":"SSLQWS","label":"Content Manager for z\/OS"},"Component":"","ARM Category":[],"Platform":[{"code":"PF025","label":"Platform Independent"}],"Version":"8.5","Edition":"","Line of Business":{"code":"LOB45","label":"Automation"}},{"Business Unit":{"code":"BU054","label":"Systems w\/TPS"},"Product":{"code":"SG19M","label":"APARs - z\/OS environment"},"Component":"","ARM Category":[],"Platform":[{"code":"PF025","label":"Platform Independent"}],"Version":"8.5","Edition":"","Line of Business":{"code":"","label":""}}]
Document Information
Modified date:
03 January 2017