Setting up a multicluster environment using General Parallel File System

Document options Document options requiring JavaScript are not displayed Rate this page Help us improve this content

Level: Advanced

Asim Kadav (asim.kadav@in.ibm.com), System Software Engineer, IBM
Mehul Joshi (mehjoshi@in.ibm.com), Staff Software Engineer, IBM

11 May 2007

Learn how to construct and deconstruct a simple multicluster of System x™ and System p™ computers using the General Parallel File System (GPFS). You can remotely add an existing GPFS cluster to another cluster. See how to mount a file system from the remote cluster using the GPFS secure communication protocol.

Introduction

General Parallel File System (GPFS) (see Resources for more information) is the parallel file system from IBM for AIX® 5L and Linux® clusters made up of System x and System p computers. GPFS is often used to create high-performance storage clusters that serve terabytes of data. You might want to mount file systems across these clusters over a wide area network. This article illustrates the steps to create a multicluster setup containing the GPFS file system. This article assumes you have basic familiarity with the terminology and concepts of GPFS.

Creating a multicluster setup

Follow these steps to create the multicluster:

1. Create two separate GPFS clusters using the techniques shown in Listing 1. Also, create NSD disks and file systems that should be mounted across clusters. A simple and concise method to create a GPFS cluster and an example file system is described in the developerWorks article Install and configure General Parallel File System (GPFS) on xSeries™ . Secure shell (ssh) access between clusters is not required. All intercluster communication is handled by the GPFS daemon, which internally uses Secure Socket Layer (SSL).
   
   Listing 1. Mounting the filesystem from the first cluster onto the second
   

   [root@gpfs-lin1 gpfs]# mmlscluster GPFS cluster information ======================== GPFS cluster name: gpfs-lin1.in.ibm.com GPFS cluster id: 699960274622719275 GPFS UID domain: gpfs-lin1.in.ibm.com Remote shell command: /usr/bin/ssh Remote file copy command: /usr/bin/scp GPFS cluster configuration servers: ----------------------------------- Primary server: gpfs-lin1.in.ibm.com Secondary server: (none) Node Daemon node name IP address Admin node name Designation ------------------------------------------------------------------------------------------ 1 gpfs-lin1.in.ibm.com 9.182.194.41 gpfs-lin1.in.ibm.com quorum-manager [root@gpfs-lin2 ~]# mmlscluster GPFS cluster information ======================== GPFS cluster name: gpfs-lin2.in.ibm.com GPFS cluster id: 699960278913802376 GPFS UID domain: gpfs-lin2.in.ibm.com Remote shell command: /usr/bin/ssh Remote file copy command: /usr/bin/scp GPFS cluster configuration servers: ----------------------------------- Primary server: gpfs-lin2.in.ibm.com Secondary server: (none) Node Daemon node name IP address Admin node name Designation ------------------------------------------------------------------------------------------ 1 gpfs-lin2.in.ibm.com 9.182.194.42 gpfs-lin2.in.ibm.com quorum-manager

   
   
   
2. Shut down GPFS (daemon) at both clusters using the command mmshutdown -a. The two clusters authenticate each other using SSL.
   
   
3. Generate a key for secure communication between the two clusters. Do this by issuing the command mmauth genkey new at Cluster 1. mmauth is a command used to manage secure access to GPFS file systems, as shown in Listing 2.
   
   Listing 2. Using mmauth to generate keys required for secure communication between clusters
   

   [root@gpfs-lin1 gpfs]# mmauth genkey new Generating RSA private key, 512 bit long modulus .........++++++++++++ .........++++++++++++ e is 65537 (0x10001) writing RSA key mmauth: Command successfully completed

   
   
4. Add security to the GPFS communication network by issuing the command mmchconfig cipherList=AUTHONLY at Cluster 1. If cipherList is not specified, or if the value DEFAULT is specified, GPFS does not authenticate or check authorization for network connections. If the value AUTHONLY is specified, GPFS does authenticate and check authorization for network connections, but data sent over the connection is not protected. Before setting cipherList for the first time, establish a public or private key pair for the cluster by using the mmauth genkey new command, as shown in Listing 3.
   
   Listing 3. Enforcing authentication using the mmchconfig command
   

   [root@gpfs-lin1 gpfs]# mmchconfig cipherList=AUTHONLY mmchconfig: Command successfully completed

   
   
5. Copy the key generated (at Cluster 1) to the remote site (Cluster 2) at any suitable location. Use the scp command or manually copy the contents of the key file. If you make a manual copy, ensure the integrity of the key file. In the example in this article, this key is cluster1.key, which is later used in our example.
   
   
6. Repeat steps 4, 5, and 6 on Cluster 2. Now both clusters have a key file from the other cluster. In the example, the second key generated is cluster2.key.
   
   
7. Start GPFS on both the clusters using the command mmsstartup -a.
   
   
8. Prepare Cluster 1 to grant secure access to the file systems it owns from Cluster 2. Issue the command mmauth add cluster2 -k /tmp/cluster2.key at Cluster 1, as shown in Listing 4.
   
   Listing 4. Adding key information about second cluster to the first.
   

   [root@gpfs-lin1 gpfs]# mmauth add gpfs-lin2.in.ibm.com -k /tmp/cluster2.key mmauth: Command successfully completed

   
   
9. Add the remote Cluster 1 to the set of remote clusters known to Cluster 2. Use the command mmremotecluster add cluster1 -k /tmp/cluster1.key -n cluster1-node, as shown in Listing 5.
   
   Listing 5. Adding the remote cluster to the secondary
   

   [root@gpfs-lin2 ~]# mmremotecluster add gpfs-lin1.in.ibm.com -k /tmp/cluster1.key -n gpfs-lin1.in.ibm.com mmremotecluster: Command successfully completed mmremotecluster: Propagating the cluster configuration data to all affected nodes. This is an asynchronous process.

   
   
10. Register the file systems from Cluster 1 that you want to access from Cluster 2 using the command mmremotefs add mygpfs -f cluster1-FS-gpfs0 -C cluster-1 -T /mygpfs, as shown in Listing 6.
    
    Listing 6. Adding the remote file system from the first cluster to the secondary
    

    [root@gpfs-lin2 ~]# mmremotefs add mygpfs -f /dev/gpfs -C gpfs-lin1.in.ibm.com -T /mygpfs mmremotefs: Propagating the cluster configuration data to all affected nodes. This is an asynchronous process.

    
    
11. Grant access to the file systems that Cluster 2 will access remotely. You can do this on each cluster one at a time using the command mmauth grant cluster2 -f cluster1.fs. If you do not want to give access to each file system separately to each cluster, use the command mmauth grant all -f all, as shown in Listing 7.
    
    Listing 7. Granting file system access to the second cluster.
    

    [root@gpfs-lin2 gpfs]# mmauth grant gpfs-lin2.in.ibm.com -f /dev/gpfs mmauth: Granting cluster gpfs-lin2.in.ibm.com access to file system gpfs: access type rw; root credentials will not be remapped. mmauth: Command successfully completed

    
    
12. Mount the file system from Cluster 2 using the mount /mygpfs command.
    
    
13. Verify your remote cluster using the commands shown in Listing 8.
    
    Listing 8. Checking successful addition of remote file systems across clusters
    

    [root@gpfs-lin2 ~]# mmremotecluster show all Cluster name: gpfs-lin1.in.ibm.com Contact nodes: gpfs-lin1.in.ibm.com SHA digest: 1a30629010ba607ed59dd011d30261482b0957c5 File systems: mygpfs (gpfs9) [root@gpfs-lin1 gpfs]# mmremotefs show all Local Name Remote Name Cluster name Mount Point Mount Options Automount mygpfs gpfs gpfs-lin1.in.ibm.com /mygpfs rw no

    
    

Back to top

Deconstructing a multicluster setup

What if you would now like to deconstruct the same multicluster? Follow these steps:

1. Unmount any individual file system and delete the file system from the remote location using mmremotefs delete remote-fsname. To remove all remote file systems at once, use mmremotefs delete all. Note that this does not delete file systems from the source cluster; it only removes them from the remote cluster. Use this command at Cluster 2, that is, where the primary cluster file system is remotely mounted, as shown in Listing 9.
   
   Listing 9. Deleting the remote file system information.
   

   [root@gpfs-lin2 gpfs]# mmremotefs delete /dev/mygpfs mmremotefs: Propagating the cluster configuration data to all affected nodes. This is an asynchronous process.

   
   
2. Delete the primary cluster configuration data from the secondary cluster with the command mmremotecluster delete cluster-name, or use mmremotecluster delete all to delete all cluster information, as shown in Listing 10.
   
   Listing 10. Deleting the remote cluster information.
   

   [root@gpfs-lin2 gpfs]# mmremotecluster delete gpfs-lin1.in.ibm.com mmremotecluster: Command successfully completed mmremotecluster: Propagating the cluster configuration data to all affected nodes. This is an asynchronous process.

   
   
3. From the primary cluster, remove the authentication information with the command mmauth delete secondary-cluster-name, as shown in Listing 11.
   
   Listing 11. Deleting the authentication information
   

   [root@gpfs-lin1 gpfs]# mmauth delete gpfs-lin2.in.ibm.com mmauth: Command successfully completed

   
   

You finished deconstructing the file system, the multicluster, and the authentication information shared between the clusters.

Share this... Digg this story Post to del.icio.us Slashdot it!

Resources

• Find more information at General Parallel File System (GPFS).
  
  
• See Install and configure General Parallel File System (GPFS) on xSeries (developerWorks, March 2006) for a step-by-step guide to installing GPFS on a single cluster.
  
  
• Refer to UID Mapping for GPFS in a Multi-cluster Environment, for a solution to the problem of handling user and group IDs in GPFS in a multicluster environment.
  
  
• Set up disaster recovery with General Parallel File System.
  
  
• Tune General Parallel File System with this sizing and tuning guide in the IBM Redbooks™ series.
  
  
• Want more? The developerWorks IBM Systems zone hosts hundreds of informative articles and introductory, intermediate, and advanced tutorials.
  
  
• Stay current with developerWorks technical events and webcasts.
  
  

• Download corrective service packages for General Parallel File Systems (GPFS) clustering software at Support for UNIX® servers and AMD and Intel® based servers.
  
  
• Build your next development project with IBM trial software for download directly from developerWorks.
  
  

• Exchange information with other developers on the IBM Systems forums and developerWorks blogs.

About the authors

		Asim is a system software engineer and a member of the General Parallel File System development team within IBM Systems and Technology Labs in Pune, India. He is currently involved in developing the file system for the Solaris platform. He holds a Bachelors degree in Computer Science from National Institute of Technology, Nagpur.

		Mehul is a staff software engineer with the IBM Systems and Technology Labs in Pune, India. He has been working for IBM since March 2004. He currently works as a General Parallel File System developer. He has previously worked on the IBM Storage Area Network file system and SPKM.

Rate this page

Please take a moment to complete this form to help us better serve you. Did the information help you to achieve your goal? Yes No Don't know   Please provide us with comments to help improve this page:   How useful is the information? 1 2 3 4 5 Not useful Extremely useful

Back to top