I get around the CCDoctor problems with this reg file entries that I run
before I install ClearCase.
Sheldon L. Buford
Configuration Management Engineer
MORGAN STANLEY Online
301 Howard Street, 4th floor
San Francisco, CA 94105
<mailto:sheldon.buford@morganstandley.com>
Tel: 415 344-9038
**********************************************************************
[HKEY_LOCAL_MACHINE\SOFTWARE\Atria\ClearCase\CurrentVersion\CCDoctor\Ignored
Problems]
"5-8"="DHCP Client Services Enabled"
"0-4"="CLEARCASE_PRIMARY_GROUP is a System Environment Variable"
"3-1"="Should Not Be in 'ClearCase' Group"
"3-3"="Potential Problem with IDE Source Control Refresh Rate"
"2-9"="Installed ClearQuest Release Not Supported By This ClearCase Release"
**********************************************************************
-----Original Message-----
From: Reedick, Andrew [mailto:JAReedick@Z-TEL.com
Sent: Monday, July 23, 2001 11:33 AM
To: 'Matt Weiss'; Reedick, Andrew; 'Lukasz Jakubowski'; cciug@rational.com
Subject: RE: [cciug] Unattended NT installation - how?
We use DHCP, so the CCDoctor dialog always shows up. =)
-----Original Message-----
From: Matt Weiss [mailto:Matt.Weiss@apropos.com
Sent: Monday, July 23, 2001 2:19 PM
To: Reedick, Andrew; 'Lukasz Jakubowski'; cciug@rational.com
Subject: RE: [cciug] Unattended NT installation - how?
One potential problem is with the Dialog that has the CCDoctor output
embedded in it. If the machine you record the response file on displays the
dialog, InstallShield will expect the dialog to appear in all dialogs.
Machines that do not display this dialog will fail under silent install.
The reverse is also true. The error code will be -12 in the setup.log file
(dialog out of order).
Matt.
-----Original Message-----
From: Reedick, Andrew [mailto:JAReedick@Z-TEL.com
Sent: Monday, July 23, 2001 12:38 PM
To: 'Lukasz Jakubowski'; cciug@rational.com
Subject: RE: [cciug] Unattended NT installation - how?
InstallShield programs give you an options to create an answer file which
will be used in the silent install. To create this file you run your
setup.exe with the -r (record) option. This creates a setup.iss file in
your windir directory. This is usually the c:\winnt on a NT system. Next
you copy the file to the same directory as the setup.exe file and run the
setup program with the -s option (silent). The setup.exe program will read
the setup.iss program. It is possible to create multiple setup.iss file and
specify which one to use by placing -f1 option.
References:
http://support.installshield.com
Knowledgebase Articles
* Q101901 - Creating a Silent Installation
* Q102392 - Setup.exe and Command Line Parameters
-----Original Message-----
From: Lukasz Jakubowski [mailto:lukaszj@s3group.com.pl
Sent: Monday, July 23, 2001 5:34 AM
To: cciug@rational.com
Subject: [cciug] Unattended NT installation - how?
Hello!
How to perform unattended NT installation? Installing form release area
still requires confirming directory and use of default options...
TIA
Regards,
Lukasz
-- *---------------------------------------------------- Lukasz Jakubowski Silicon & Software Systems Poland, Information Office +48 71 33-48-132, lukasz.jakubowski@s3group.com-----* - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
This archive was generated by hypermail 2b29 : Tue Jul 31 2001 - 22:04:00 EDT